ASTM A182 F5 F9 F11 F12 F22 F91 Flanges A182 F9 Steel Slip On Flanges

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Alloy steel flanges have corrosion oxidation stress corrosion cracking and crevice corrosion resistance.

At elevated temperatures, conventional steels, unlike ASTM A 335 P91 pipes, begin to lose their microstructural form, leading to failure. A burst or crack in the pipe is a visible fault. But since SA 335 P91 chrome-plated welded pipe is well suited to sustain itself at high temperatures, failure rates are extremely low.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

For the F5 flange, the creep strength of the chromium-molybdenum low alloy mainly comes from two sources: the solid solution strengthening of the matrix ferrite by carbon, molybdenum and chromium and the precipitation hardening of the carbides.

Alloy Steel F11 Flanges specifications are also mentioned and the face type starts from flat face, raised face, ring type joint and many more.

Low alloy steels contain trace amounts of alloying agents such as niobium, nitrogen, vanadium, copper, nickel, chromium, titanium, calcium, molybdenum, rare earth elements or zirconium.

Monel 400? can be used in temperatures up to 1000 oF. Monel K-500 is basically a better version of 400 and has higher strength and hardness.

The alloy must be cooled for heat treatment prior to AISI AS F11 Hex Bar. All parameters of the heat treatment procedure are set by the specification, including the type of heat treatment, austenitization/solution temperature, and alloy steel F11 A182 bars.

Alloy pipe is a higher percentage of tubular alloying elements such as molybdenum (Mo), chromium (Cr), nickel, etc. than standard carbon steel pipe. In fact, ASTM A335 covers “low alloy” steel pipes, that is, having less than 5% total alloying elements. The addition of higher percentages of alloying elements such as nickel and chromium converts the steel into higher alloys such as stainless steel, duplex stainless steel, up to superalloyed materials such as Inconel, Hastelloy, Monel, etc.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P100

There are different schedules for P91 metal piping materials, corresponding to different pressure classes. sa335 P91 seamless pipe can withstand high pressure and high temperature and can also be welded to other pipes and fittings.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.27

ASME SA 335 P91 Alloy Steel Pipe also has some other great features like low maintenance, efficient work, high demands, etc. We offer a range of ASTM A335 P91 alloy steel pipes for a wide range of applications in various industries.

Unlike the bends, the elbows can reduce the pressure applied on the walls when turning the fluid flow direction.Fittings made from WPHY 52 material are known to have a long work life, durable, tough and hard. The WPHY 52 properties make these fittings a perfect cost saving solution for a variety of industries.

A182 alloy flange has good dimensional accuracy.

Imperative for the uniqueness of Alloy Steel F9 Socket Weld Flanges is the allotropy of iron-that is, its existence in two crystalline structures. Alloy Steel(AS) F9 Long Weld Neck Flanges can be carbide of an alloying element such as titanium.

The high lead content in STM A320 grade L7M AS bolts results in relatively low ductility and plasticity.

Chromium-molybdenum alloy flanges connect pipes, valves, pumps and other equipment to form a piping system. They are ideal for applications that convey corrosive or high temperature fluids or gases.

Forged Pipe Fittings (Socket Weld and Threaded) are made in
accordance to ASME B16.11, MSS-SP-79/ 83/ 95/ 97 and BS3799
standards, and are used to connect nominal bore schedule pipes
and pipelines.

The ASTM A320 Grade L7 specification covers stainless steel bolting materials for low temperature service. This standard cover rolled, forged, or strains hardened bars, bolts, screws, studs, and stud bolts used for pressure vessels, valves, flanges, and fittings.

HastelloyC-276 (Hastelloy) is a tungsten-nickel-chromium-molybdenum alloy with extremely low silicon-carbon content and is considered to be an all-around corrosion-resistant aluminum alloy. The key moisture-resistant chlorine, various air-oxidizing fluorides, isopropyl titanate solutions, hydrochloric acid and air-oxidizing salts, have good corrosion resistance in ultra-low temperature and standing temperature sulfuric acid. Therefore, in the past 30 years, it has been widely used in extremely corrosive natural environments such as chemical plants, petrochemicals, flue gas desulfurization, pulp and paper industry, and environmental protection.

Corrosion resistance

The aluminum alloy has the following characteristics: 1. It has good corrosion resistance to most corrosive substances under the two conditions of air oxidation and repair. ¢ÚIt has good resistance to pitting corrosion, void corrosion and intergranular corrosion. The higher content of Mo and Cr makes the aluminum alloy resistant to corrosion by chloride ion content, and the W element further improves the corrosion resistance. At the same time, Hastelloy C-276 aluminum alloy is one of the only types of raw materials that are resistant to wet chlorine, hypochlorite and chlorine dioxide saturated solutions. Ester solution has obvious corrosion resistance. It is one of the very few raw materials that can be used as a hot sulfuric acid saturated solution.

ASTM A335 P11 pipe (ASME SA335 P11) is a chromium-molybdenum alloy seamless pipe for high temperature service. P11 grade pipe has a chromium content of 1.00% to 1.50%, a molybdenum content of 0.44% to 0.65%, and a minimum tensile strength of 415MPa. Minimum yield strength 205Mpa.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P131

When connecting these parts, put gasket in the middle of two flanges, then tightening the flange screws, so the two will be connected together tightly.

The plates are annealed in different condition which offers them strength. Since these plates are to be worked at high temperatures and pressure environment therefore the elements included in it matters a lot. What elements are added in the manufacturing add different properties for example, high level of chromium adds excellent corrosion resistance. It also offers excellent oxidation resistance. Resistant to oxygen is important in petrochemical and gas industries and therefore these plates are used.

ASTM A193 Grade B7 is the standard material specification for chromium-molybdenum alloy steel fasteners for high-strength, high-temperature, and special-purpose applications. Grade B7 is a heat treated chromium molybdenum alloy steel with a minimum tensile requirement of 100 ksi, a yield strength of 75 ksi and a maximum hardness of 35 HRC. The ASTM A193 specification covers requirements for chemical composition, mechanical properties, hardness, heat treatment, and recommended nut washers for Class B7 fasteners. ASTM A193 Grade B7 is the broadest specification for fasteners, commonly found in bolts or pipes, pressure vessels, valves, flanges and fittings.

A182 pipe flanges tend to have fairly high electrical conductivity among other wrought alloy steels in their class. It has a higher base cost and higher embodied energy.

ASTM A182 is the Standard Specification for Forged Stainless Steel Pipe Flanges and Stainless Steel Forged Fittings.

These pipes are highly resistant to high temperature and corrosive environments. The absolute roughness of astm a335 gr P9 seamless pipe is small, so the size is very accurate.

Alloy steel grade 2H gaskets are further cut, hydrotested, annealed, straightened and pickled. The manufacturing process of our Alloy Steel Grade 2H Split Gaskets is carried out in a state-of-the-art production facility under the proper supervision of industry experts.

Our ASTM A182 F5 alloy steel blind flanges are used in auxiliary industrial high pressure services such as heat exchangers, condensers, evaporators, boilers, etc.

To be sure, huge numbers of the reactions of Alloy Steel F9 Slip On Flanges meddle with each other, requiring the utilization of process models to help in analysing alternatives, improving contending reactions, outlining productive commercial practices. The specification is for high temperature pressure services. The SA 182 Gr F9 Steel Pipe Flanges come in the size range of ? inches to 48 inches with dimensions varying according to the ASTM, ASME and other international standards.

ASME SA 335 P11 pipe is a pipe made of chrome molybdenum alloy. It is used for high temperature service. It is corrosion resistant, strong and malleable.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.53

The most common application for A182 F2 round bars is shafts. It has various alloying elements that enhance its mechanical properties.