ASTM A182 F5 F9 F11 F12 F22 F91 Flanges Chromium AS Pipe Flanges

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

The high chromium content gives these alloy steel socket weld flanges very good resistance to moisture erosion, which also contributes to their high temperature strength and resistance to scaling at high temperatures.

HastelloyC-276 (Hastelloy) is a tungsten-nickel-chromium-molybdenum alloy with extremely low silicon-carbon content and is considered to be an all-around corrosion-resistant aluminum alloy. The key moisture-resistant chlorine, various air-oxidizing fluorides, isopropyl titanate solutions, hydrochloric acid and air-oxidizing salts, have good corrosion resistance in ultra-low temperature and standing temperature sulfuric acid. Therefore, in the past 30 years, it has been widely used in extremely corrosive natural environments such as chemical plants, petrochemicals, flue gas desulfurization, pulp and paper industry, and environmental protection.

Corrosion resistance

The aluminum alloy has the following characteristics: 1. It has good corrosion resistance to most corrosive substances under the two conditions of air oxidation and repair. ¢ÚIt has good resistance to pitting corrosion, void corrosion and intergranular corrosion. The higher content of Mo and Cr makes the aluminum alloy resistant to corrosion by chloride ion content, and the W element further improves the corrosion resistance. At the same time, Hastelloy C-276 aluminum alloy is one of the only types of raw materials that are resistant to wet chlorine, hypochlorite and chlorine dioxide saturated solutions. Ester solution has obvious corrosion resistance. It is one of the very few raw materials that can be used as a hot sulfuric acid saturated solution.

Chromium-molybdenum alloy steel has strong crack resistance under high temperature and high pressure. Chromium molybdenum is also resistant to hydrogen attack and hot sulfide corrosion cracking.

The composition of A335 P91 material contains carbon, manganese, phosphorus, sulfur, silicon, chromium, molybdenum, vanadium, nitrogen, nickel, aluminum, niobium, titanium and zirconium. There are two kinds of seamless pipes and welded pipes. Seamless pipe is drawn from a single raw material billet, while ASTM A335 Gr P91 Welded Pipe is welded from strip or sheet. Welding can be helical or longitudinal from one end to the other to produce the tube. The minimum yield strength of the pipe is 415MPa and the minimum tensile strength is 585MPa.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.60

Since these are heavy duty tension nuts, they are used in high vibration and high stress applications such as aircraft engine parts and automotive engine parts. ASTM A194 Class 2h material consists of all classes of carbon, manganese, phosphorus, sulfur and silicon.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Due to its ease of welding, ASTM A335 Grade P91 Welded Pipe can be welded well into piping systems. Pipes have different tolerance classes and test standards depending on the application requirements, grade, schedule and pressure rating of the pipe material.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.28

A182 threaded flanges are primarily used for utility services such as air and water. It is similar to a Slip-On flange, but the holes are threaded.

ASTM A335 P91 Seamless Pipe is one of the seamless pipes that standardize A335 in various industries. ASME SA 335 Grade P91 Alloy Steel Pipe is made of chrome molybdenum alloy. These pipes contain 1% molybdenum, 9% chromium and nickel, manganese, silicon and carbon. ASTM A335 P91 pipe has very high tensile strength, yield strength, impact cracking resistance, corrosion cracking resistance and oxidation resistance.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.23

This is useful for selecting bolts with different strength levels for different high pressure and high temperature applications. ASTM A193 grade b7 hex bolts and other types have a minimum tensile strength of up to 125ksi.

It exhibits exceptional corrosion resistance in chemical environments containing phosphoric acid, nitric acid, chlorides and sulfuric acid. It also has good mechanical properties at both ambient and elevated temperatures.

Grade P11 is known as chrome molybdenum alloy steel. Compared to carbon steel, the properties of this alloy steel are much higher. Typically, alloy steels such as ASTM A335 P11 pipe tend to have much higher element percentages than conventional steels. So take their efficiency to the next level. The alloy composition of the P11 grade consists of chromium and molybdenum, with a chromium percentage of approximately 1.25. The content of molybdenum in the alloy steel P11 seamless pipe is about 0.5%.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P124

A320 Gr L7 studs are subject to certain mandatory mechanical tests, namely: tensile test, impact test and hardness test.

WPHY 52 Fittings are recommended be heat treated by one or more of the following procedures: annealing (stress relieving), normalizing, normalizing and tempering, quenching and tempering.Made utilizing high-grade crude materials, these ASTM A860 WPHY Pipe Fittings are anti-corrosive and strong.

We are a manufacturer, supplier and exporter of Plate Flanges, which are accepted by major industries as a cost-efficient alternative to other types of flanges whose cost increases due to its expensive production pattern.

Chrome moly alloy flanges connect pipes, valves, pumps and other equipment, forming a piping system.

While chromium is an important alloying agent in a335 P91 piping, it is known to prevent corrosion and has a high resistance to oxidation at high temperatures. Since these pipes are surface treated or coated, they are also protected against corrosion. Surface coating can be accomplished by various techniques such as passivation, phosphating, oil immersion, varnishing and shot peening.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P150

Alloy 20 (Alloy 20) is an iron-based austenitic alloy developed to resist sulfuric acid corrosion. It has excellent resistance to sulfuric acid corrosion; it has strong resistance to phosphoric acid, nitric acid and chloride environments, chloride stress corrosion, pitting corrosion and crack corrosion. Therefore, alloy 20 has the name of anti-corrosion alloy; it has a wide range of applications: such as: chemical, food, medicine, power production and plastics industries will use it. For resistance to pitting corrosion and chloride corrosion, stress corrosion cracking problems, etc., alloy 20 is often used.

This specification covers forged low alloy flanges for use in pressure systems manufactured to specified dimensions or industry standard dimensional specifications.

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

A weld neck flange, also called a tapered hub flange or high-hub flange, is a kind of flange that can relocate stress to the pipes, ensuring a decrease in high-stress concentration at the bottom of the flange.

The range of pipe diameters of A335 that can be tested by each method should be limited by the respective scope of practice. The different mechanical testing requirements for pipes, i.e. transverse or longitudinal tensile tests, flattening tests, hardness or bending tests, are presented.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.22

Adding nickel adds toughness to the alloy. Similarly adding chromium to chrome moly flanges aids in enhancing other mechanical properties such as temperature strength, hardness, as well as corrosion resistance.

Alloy steel hollow bars offer excellent corrosion resistance and dimensional accuracy with tight tolerances.

Its tensile strength is 380 Mpa, while its yield strength is 585 Mpa at 0.2% Offset. The elongation of astm a182 gr f9 is 20 %.

Low alloy steels contain trace amounts of alloying agents such as niobium, nitrogen, vanadium, copper, nickel, chromium, titanium, calcium, molybdenum, rare earth elements or zirconium.

The Chromium content in the alloy aids in improving its anti-oxidization and anti-corrosion properties. This steel is usually supplied by the alloy steel flanges manufacturers in India in an annealed or normalized and tempered condition.

ASTM A193 Grade B7 bolts and studs are made from chrome molybdenum steel and are quenched and tempered (heat treated) to achieve the desired mechanical properties (strength). Grade B7 is the most commonly used A193 bolt grade in construction.

The chromium content in the A335 p9 pipe makes it highly resistant to corrosion. Therefore, A335 p9 has excellent high temperature oxidation resistance. In addition to chrome, Astm A335 p9 alloy steel pipe coated with black paint or anti-corrosion oil shows good corrosion resistance. It can also be galvanized with zinc. Galvanizing increases its resistance to atmospheric corrosion.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P147

A335 grade P9 alloy steel round pipe is your best choice. It surrounds pipes made of alloy steel. It’s graded very well, making it unique. It has excellent properties such as toughness, durability, weldability, and low electrical conductivity.