ASTM A193 B7 B8C B8CA alloy steel hex bolt full half thread

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

The Alloy Steel F12 Flanges are also very strong due to the annealing of them. Grade F12 Flanges can be supplied in either normalized or quenched and tempered conditions. Alloy Steel F12 Weld Neck Flanges is appropriate to various applications where its different remarkable characteristics are sought-after but a brushed/polished finish is not necessary.

The Chromium content in the alloy aids in improving its anti-oxidization and anti-corrosion properties. This steel is usually supplied by the alloy steel flanges manufacturers in India in an annealed or normalized and tempered condition.

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

The addition of molybdenum strengthens the elastic limit of the A335 p11 welded pipe and increases its temperature strength. In addition to these properties, there is a reduction in brittleness and an improvement in the weldability and hardenability of the pipe.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.48

Please make sure to contact us for more information on the pipe fitting products such as the ASTM A860 MSS SP 75 WPHY 52 Pipe Fittings and their pricing.

ASTM A194 2h nuts are available in nominal sizes ranging from ?” to 4″. These products are made with heavy duty hex nuts with different proof load stresses for regular nuts and zinc plated nuts. A194 2h coupling nut with 175ksi plain nut and 150ksi zinc plated nut. Fasteners of this grade of material also have high hardness.

A weld neck flange, also called a tapered hub flange or high-hub flange, is a kind of flange that can relocate stress to the pipes, ensuring a decrease in high-stress concentration at the bottom of the flange.

Alloy steel is divided into two categories: high-alloy steel and low-alloy steel. Low alloy steel flanges, on the other hand, contain about 0.05 ¨C 0.25% carbon and up to 2.0% manganese.

ASTM A182 Grade F5 Flanges are suitable for connecting pipes of small bore size and without the requirement of welding. ASTM A182 GR F5 Flange belongs to the ASTM A182 specification. The dimensions of the flanges vary according to the ANSI, ASME and DIN standards. The flange sizes range from ? inches to 36 inches in nominal bore sizes. Navstar Steel is a leading supplier and manufacturer of these flanges in various sizes and types.

This is the widely used product in many other industries and is thus manufactured with utmost care and the packaging of this is also done with great care and is then dispatched to various other applications.

ASTM A182 F11 Alloy Steel Flanges are used in manufacturing of flanges and fittings and are used in industries where cold temperature is observed and corrosion resistance doesn¡¯t matter much.

Alloy steel F12 square bars can withstand very high temperatures with minimal product aging even after thousands of operating hours,

The flange connection type usually comes with double units, with a gasket and some bolts & nuts to connect each other. (Firstly pipes are welded on the flanges, then valves and other equipment could be installed on flanges.)

When moving high-temperature or corrosive media through Chrome Alloy Pipe from one process to the next, flanges capable of withstanding harsh environments are critical

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

The ANSI B16.5 Alloy Steel Slip On Flange is a flange type that allows the pipes to slip onto the flange and makes the connection in a precise locations.

Cold drawn and cold rolled tube types are available. There are seamless tubes, welded tubes, ERW tubes and fabricated tubes. Seamless pipe is made from a single piece of material, whereas ASTM A333 Grade 6 Welded Pipe Specification requires it to be welded from strip or sheet of the same material grade.

L7 threaded studs and short head bolts are readily available in the market.

Flange is usually used for connecting pipes or valves, so it can solve the above problems easily.

Alloy Steel F5 Flanges are square-shaped and are instrumental in interfacing pipes of nominal bore size without welding and are reasonable for high pressure hydraulic frameworks. ASTM A182 F5 Lap Joint Flanges go by a range of names, including back up flange, loose hubbed flange, loose ring flange and van stone flange. ASTM A182 Gr F5 Blind Flanges are commonly used in petrochemical, pipe engineering, public services and water works.

High alloy steel is defined by a high percentage of alloying elements.

When connecting these parts, put gasket in the middle of two flanges, then tightening the flange screws, so the two will be connected together tightly.

In applications where higher working pressures are a prerequisite, the use of seamless pipes is justified. Although stronger than welded pipe, the cost is much higher. In addition, in welded products, there is a greater risk of intergranular corrosion in the heat-affected weld zone. The obvious difference between alloy steel welded pipe and seamless product is the transverse seam along the length of the pipe
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P128

The connection between two pipes can be directly welded together, but it is difficult to connect together without welding. When the connection part have problems, it will be hard to repair. The same problem also happened between pipe and valve connection.

Monel 400? sheet is available in thicknesses ranging from .018 to .140″.Butt-weld and forged fittings are available or can be manufactured with short lead times.

ASTM A320 L7 washers are specially engineered for LOW temperature performance. These fasteners are commonly used for valves, flanges, fittings, and pressure vessels.

Chromium increases the tensile, yield and hardness of steel at room temperature. This is why ASTM A335 chrome-molybdenum alloy seamless steel pipes are mainly used in power plants, refineries, chemical plants and oilfield platforms where fluids and gases are transported under extremely high temperatures and pressures.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P97

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

Our products are a symbol of constant innovation and superior quality.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.