astm a333 grade 6

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

A335 P22 Chromium Pipe contains chromium in its composition to provide high corrosion resistance. There are other elements in the material composition of P22 steel pipe. Molybdenum is a common addition in all A335 grades. Manganese, phosphorus, silicon and carbon are added according to different grades.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.43

The range of pipe diameters of A335 that can be tested by each method should be limited by the respective scope of practice. The different mechanical testing requirements for pipes, i.e. transverse or longitudinal tensile tests, flattening tests, hardness or bending tests, are presented.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.22

SA 182 Gr F1 Slip on Flanges also known as SO flanges. This is a flange that slides over the pipe and has an internal design that is slightly larger than the pipe.

Alloy Steel F12 slip on Flanges are made up of chromium molybdenum steel alloy and therefore have a high rupture resistance. They are also preferred due to their light weight because of the low carbon and high alloy nature.Alloy Steel ASTM A182 flanges are very simple to install and have a low center because the pipe occasionally trips into the flanges after welding.

The high chromium content gives these alloy steel socket weld flanges very good resistance to moisture erosion, which also contributes to their high temperature strength and resistance to scaling at high temperatures.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

ASTM 182 is use in pressure systems, Included are flanges, fittings and similar parts to specified dimensions or to dimensional standards, such as the ASME specifications. 182 F5 Cl2 Alloy Steel Flanges are well suited to not only high temperature but also high pressure or a combination of both these applications.

Alloy A182 flange also has durability and longevity.

Hastelloy C276 ASTM Standard B575 Plate is a nickel-molybdenum-chromium superalloy with an enhancement of tungsten made to have superb deterioration resistance in a wide variety of extreme atmospheres.

High alloyed types of steel are favored in the plumbing industry for use in extreme conditions, be it hot or cold, or subjected to rough service. This is because a combination of chemistry and proper heat treatment can result in a strong and flexible pipe that can withstand blows. Alloy pipes are often favored by the oil and gas and power generation industries due to their toughness.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.43

A182 pipe flanges tend to have fairly high electrical conductivity among other wrought alloy steels in their class. It has a higher base cost and higher embodied energy.

It is a standard specification defining typical chemical composition, mechanical properties, hardness requirement, preferential heat treatment, product marking, certification and other requirements, suitable for bolting used in pressure vessel service, valves, flanges and fittings. ASTM A193 defines both SI (Metric) and inch-pound units.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

ASTM A 182 Alloy Steel GR F11 Round bars are generally considered less robust than stainless steel alloys, and their price plays an important role in the purchase.

The A182 F9 Alloy Steel Blind Flanges are used to close a connection opposed to all other flanges which extend the pipeline. Alloy Steel ASTM A182 F9 Flanges is connected to the pipe by welding the pipe to the neck of the pipe flange. However, the inside diameter of ASTM A182 F9 Alloy Steel Flanges is being designed to match the inner diameter of the pipe.

When the F11 flange is heat treated, the alloy steel F22 flange is formed. These flanges have a tensile strength of 655 MPa and a yield strength of 517 MPa.

Nuts with a nominal size over 1 inch shall be a UNC Series Class 2B fit or an 8 UN Series Class 2B fit. High strength ASTM A194 grade 2H nuts are common in the market and are often replaced by ASTM A563 grade DH nuts due to the limited availability of DH nuts in certain diameters and finishes.

Alloy steel is divided into two categories: high-alloy steel and low-alloy steel. Low alloy steel flanges, on the other hand, contain about 0.05 ¨C 0.25% carbon and up to 2.0% manganese.

Chromium-molybdenum alloy steel has strong crack resistance under high temperature and high pressure. Chromium molybdenum is also resistant to hydrogen attack and hot sulfide corrosion cracking.

ASTM A193 B7 bolts are manufactured to meet numerous specifications and material design properties. More specifically, B7 alloy steel is a high temperature grade of A-193. B7 steel is also a chromium molybdenum steel with a minimum tensile strength of 125ksi.

The material has high creep resistance and corrosion resistance. The molybdenum content provides creep resistance and pitting resistance to the pipe. ASTM A335 P22 pipe is suitable for high temperature service. The ability to use at high temperatures comes from the ingredients. The composition of ASTM A335 P22 welded pipe contains carbon, manganese, phosphorus, sulfur, silicon, chromium and molybdenum.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.56

ALLOYS STEEL SA 182 F9 BAR is a ferritic alloy steel bar, other contents are also considered. These bars are steel forged bars held at high temperature and pressure.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

ASTM A335 P5 pipe can be fully annealed or isothermally annealed, normalized and tempered as heat treatments to increase hardness. This grade is available in welded and seamless pipe, A335 P5 welded pipe is available in different wall thicknesses and diameters.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P121

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Flanges are usually welded or threaded. Flange joints are made by bolting two flanges together with a gasket between them to provide a seal.

The alloy content of pipes that make up low alloy steel is less than 5%. High alloy steels, on the other hand, have an alloy content ranging from 5% to about 50%. Similar to most alloys, the working pressure capacity of alloy steel seamless pipe is about 20% higher than that of welded pipe.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P127

Monel 400? can be used in temperatures up to 1000 oF. Monel K-500 is basically a better version of 400 and has higher strength and hardness.

Alloy steel DIN 1.7335 round bars also offer some other outstanding properties such as perfect finish, dimensional stability, light weight, high load-carrying capacity, longer life, fine dimensions and more.

Inconel600 is suitable for welding with the same material or other metals by any traditional welding process, such as tungsten electrode inert gas welding, plasma arc welding, manual sub-arc welding, metal inert gas shielded welding, molten arc inert gas shielded welding, and pulsed arc welding. Welding is the preferred solution. When using manual arc welding, it is recommended to use a shielding gas mixed with various components (Ar+He+H2+CO2).
Welding of Incoloy 825 must be carried out in the annealed condition and cleaned with a stainless steel wire brush to remove stains, dust and various markings. When welding the root of the weld, extreme care must be taken (Argon 99.99) to obtain the best quality of the root weld so that the weld does not produce oxides after the root has been welded. Color from the weld heat-affected zone should be removed with a stainless steel brush while the weld area is not cool.