astm a335 grp22 large diameter alloy pipe

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Our Alloy Steel ASTM A182 F5 Weld-neck Flanges are supplied to aid industrial, high pressure services like condensers, boilers, evaporators, heat exchangers, etc. Alloy steel F5 A182 flanges is also available in the form of lap joint flanges, plate flanges, threaded flanges, reducing flanges and many more. These flanges are widely used in power generation industry, gas processing industry, pharmaceutical industry, heat exchangers industry, sea water equipment industry, oil drilling companies and many more.

SA 182 Gr F1 Slip on Flanges also known as SO flanges. This is a flange that slides over the pipe and has an internal design that is slightly larger than the pipe.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

ASTM A320 bolts are suitable for low temperature service down to -150¡ãF and have a minimum Charpy impact value of 20-ft-lbf at this temperature. ASTM A320 Hex Bolts must obtain the durability and service of high temperature or high pressure and corrosion resistant steel. ASTM A320 Stud Bolts are available in different sizes and patterns, our premium ASTM A320 Grade L7 AS Bolts are in high demand in the market due to their speculative properties and specifications.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Grades 7, 7M, 8 and 8M have 8-10% nickel added. Grade 8 material lacks molybdenum, but Grade 8M ASTM A194 2h material contains all the elements mentioned in the composition, making it the strongest and most expensive class of materials in this grade.

Producing Standard
ASME B18.2.2
DIN 934 

The alloy steel of ASTM A182 F11 flanges is called chrome-moly flanges. These are flanges that contain chromium and molybdenum, these are the ingredients that make them resistant to corrosion, which also adds to its toughness.

A193 B7 Cadmium Plated stud bolts are made of alloy steel for high temperature environments. ASTM standards cover alloy steel and stainless steel bolting materials; this specification covers fasteners for pressure vessels, valves, flanges, and fittings.

A194 2H Heavy Duty Hex bolts are designed for high strength, high temperature or high pressure applications and are usually available in a plain finish.

To be sure, huge numbers of the reactions of Alloy Steel F9 Slip On Flanges meddle with each other, requiring the utilization of process models to help in analysing alternatives, improving contending reactions, outlining productive commercial practices. The specification is for high temperature pressure services. The SA 182 Gr F9 Steel Pipe Flanges come in the size range of ? inches to 48 inches with dimensions varying according to the ASTM, ASME and other international standards.

The corrosion resistance of SA 335 P91 seamless pipe is much higher than that of carbon steel. Grade P91 is a reference for the chemical composition of alloy steels. A chromium-molybdenum steel, the chemical composition of ASTM A335 P91 alloy steel pipe consists of 9% chromium and 1% molybdenum and vanadium.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.22

A182 threaded flanges are primarily used for utility services such as air and water. It is similar to a Slip-On flange, but the holes are threaded.

ASTM A182 lap flanges are known by a variety of names, including support flanges, loose flanges, loose ring flanges, and van stone flanges.

Weld Neck Flange is expensive because of its long neck and cost of people for contact WN flange with pipeline or fitting but is preferred for high-stress applications. The necks, or hubs, transmits stresses to the pipeline.

ASTM A182 Alloy Steel Blind Flanges is a solid disk used to block off a pipeline or to create a stop. It has mounting holes around the perimeter and the gasket sealing rings are machined into the mating surface.

The alloy steel slides on these flanges can be machined and polished in a stress-relieved condition.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

The product portfolio is designed to be durable plumbing components, a sustainable alternative with premium quality that aids business growth.

Alloy steel pipes are used in applications requiring moderate corrosion resistance, good durability, and economical cost. Simply put, alloy pipes are preferred in those areas where carbon steel pipes can fail. There are two types of alloy steel – high alloy steel and low alloy steel.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P126

ASTM A320 L7M Grade AS Fasteners are commonly used in oil and gas exploration and processing equipment – piping, piping and heat exchangers.

A182-F11 is an American standard pearlitic structure heat-resistant steel forgings, the execution standard: ASTM-A182/A182M-2017.

We can supply chrome molybdenum alloy flanges sorted by alloy grade, size and pressure.

INCONEL? alloy 718 (UNS N07718/W.Nr. 2.4668) is a high-strength, corrosion-resistant nickel chromium material used at -423¡ã to 1300¡ãF. Inconel alloys are resistant to oxidation and have the ability to maintain its structural integrity in high temperature atmospheres.

There are different schedules for P91 metal piping materials, corresponding to different pressure classes. sa335 P91 seamless pipe can withstand high pressure and high temperature and can also be welded to other pipes and fittings.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.27

The range of pipe diameters of A335 that can be tested by each method should be limited by the respective scope of practice. The different mechanical testing requirements for pipes, i.e. transverse or longitudinal tensile tests, flattening tests, hardness or bending tests, are presented.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.22

ASTM A182 Gr F11 class 2 pipe flange has low thermal conductivity and moderately low tensile strength and also has many other properties like great quality, toughness and many other points.

Alloy steel pipe is made of iron base. It has a complete austenite structure and has good corrosion resistance to various corrosive media. These pipes and tubes are the most cost-effective option for long-lasting applications.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.32

Unlike the bends, the elbows can reduce the pressure applied on the walls when turning the fluid flow direction.Fittings made from WPHY 52 material are known to have a long work life, durable, tough and hard. The WPHY 52 properties make these fittings a perfect cost saving solution for a variety of industries.

Whether manufactured to ANSI, ASME or custom standards, flanges are critical to manufacturing, utility and industrial applications around the world.