astm a335 p5 alloy

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

ASTM 182 is used for pressure systems, including fittings, flanges,and similar parts that conform to specified dimensions or dimensional standards such as ASME codes.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Alloy steel pipe is an economical section steel. Widely used in the manufacture of structural and mechanical parts, such as oil drill pipes, automobile drive shafts, bicycle frames and steel scaffolding for construction. Making ring parts with alloy steel pipes can improve material utilization, simplify the manufacturing process, save materials and processing time, such as: filling bearing rings, jack sleeves, etc. At present, steel pipes have been widely used in manufacturing.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.25

These are also added with limited amounts of elements like sulphur, silicon, manganese and phosphorous that helps in increasing ¨C Hardness, Strength, Chemical resistance, and more.

Grade P11 is known as chrome molybdenum alloy steel. Compared to carbon steel, the properties of this alloy steel are much higher. Typically, alloy steels such as ASTM A335 P11 pipe tend to have much higher element percentages than conventional steels. So take their efficiency to the next level. The alloy composition of the P11 grade consists of chromium and molybdenum, with a chromium percentage of approximately 1.25. The content of molybdenum in the alloy steel P11 seamless pipe is about 0.5%.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P124

Chrome moly flanges provide improved levels of chromium and molybdenum. The addition of chromium helps to increase itshardenability and corrosion resistance,

ASTM A194 2h nuts are available in nominal sizes ranging from ?” to 4″. These products are made with heavy duty hex nuts with different proof load stresses for regular nuts and zinc plated nuts. A194 2h coupling nut with 175ksi plain nut and 150ksi zinc plated nut. Fasteners of this grade of material also have high hardness.

There are different types and grades of the blind flanges as well. There are other different types of ASME SA 182 AS Pipe Flanges such as the weld neck flanges and socket weld flanges each specified for a particular role

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

The plates are annealed in different condition which offers them strength. Since these plates are to be worked at high temperatures and pressure environment therefore the elements included in it matters a lot. What elements are added in the manufacturing add different properties for example, high level of chromium adds excellent corrosion resistance. It also offers excellent oxidation resistance. Resistant to oxygen is important in petrochemical and gas industries and therefore these plates are used.

A335 has improved wear resistance at higher temperatures. It has good formability and machinability without deformation and deformation. It has good thermal stability in pressurized environments.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.35

Alloy Steel F11 Flanges specifications are also mentioned and the face type starts from flat face, raised face, ring type joint and many more.

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

ASTM A182 Alloy Steel Blind Flanges is a solid disk used to block off a pipeline or to create a stop. It has mounting holes around the perimeter and the gasket sealing rings are machined into the mating surface.

Compared to other manufacturing process, ASTM A182 F22 Metal forging is mainly focused on producing some of the strongest manufactured parts. It¡¯s not just limited to iron and steel forging but as well as other metals also.

These pipes are highly resistant to high temperature and corrosive environments. The absolute roughness of astm a335 gr P9 seamless pipe is small, so the size is very accurate.

The carbon content of 4140 alloy steel pipe is 0.38-0.43%, the manganese content is 0.75-1.00%, the phosphorus content is 0.04%, the sulfur content is 0.04%, the silicon content is 0.15-0.35%, the chromium content is 0.8-1.10%, and the molybdenum content is 0.8-1.10%. is 0.15-0.25 % maximum in its composition. The material can be heat treated to anneal and normalize in air, or quench and temper in polymer or oil.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P138

Alloying steels have added alloying elements such as manganese and nickel. These elements increase the strength, hardness and toughness of metals. Added elements make alloy steels ideal for demanding industrial applications.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.24

Weld Neck Flange is flanges that designed to be joined to a piping system by butt welding. This kind of flange include lots of specification.

A182 F2 round bar has high strength, formability and hardenability.

ASTM A860 MSS SP 75 WPHY 52 Fittings are generally used at High Pressure requirements.Our wide range of Grade WPHY 52 Pipe Fittings includes: WPHY Gr 52 Bend, Elbow WPHY 52 in 45/90 degree, WPHY Grade 52 Tees, Carbon Steel WPHY 52 U Bend, MSS SP75 WPHY Gr 52 Stubends & ASTM A860 WPHY Grade 52 Pipe Nipple.

A335 P9 seamless pipe is a type of chrome molybdenum pipe listed in ASTM A335 (ASME S/A335, Chrome-Moly), which has become the standard in the power generation industry and petrochemical industry, not only because of its tensile strength, corrosion resistance resistance and high temperature strength, but also because of its cost-effectiveness. Chromium molybdenum tubes are popular in P grades P5, P9, P11, P22, P91 and P92. The P11, P22 and P91 grades are most commonly used in the powder industry and petrochemical plants, while the P5 and P9 grades are often used in oil refineries.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.66

For the F5 flange, the creep strength of the chromium-molybdenum low alloy mainly comes from two sources: the solid solution strengthening of the matrix ferrite by carbon, molybdenum and chromium and the precipitation hardening of the carbides.

Our alloy steel ASTM A182 F5 butt weld flanges can be used in auxiliary industrial high pressure services such as condensers, boilers, evaporators, heat exchangers and more.

Our ASTM A182 F5 alloy steel blind flanges are used in auxiliary industrial high pressure services such as heat exchangers, condensers, evaporators, boilers, etc.

A182 threaded flanges are primarily used for utility services such as air and water. It is similar to a Slip-On flange, but the holes are threaded.

We offer ASME SA335 Grade P22 Welded Pipe, ASTM A335 P22 Pipe is manufactured according to ASTM standards. Alloy steel A335 P22 ERW tube, Astm A335 P22 temperature extreme cold formed, made from steel strip drawn through a series of rolls.

ASTM A193 Grade B7 bolts are considered for applications up to 450¡ãC due to heat treated chrome molybdenum steel. B7 stud bolts are bolts with male threads and a hex head designed to be actuated by a wrench. It can be fully threaded or partially threaded and is supplied with a hex cap.

We also provide various alloy steel ASTM A182 F5 flanges, such as ASTM A182 F5 slip-on flanges, alloy steel F5 butt weld flanges, F5 alloy steel socket weld flanges, A182 F5 alloy steel blind flanges, alloy steel F5 Orifice Flange, A182 Alloy Steel F5 Blind Flange, A182 F5 Threaded/Threaded Flange, Alloy Steel F5 Reducing Flange, ASTM A182 F5 Alloy Steel Ring Type Joint Flange (RTJ) etc.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.