ASTM A403 WP304H pipe fittings elbows

Sanitary Weld Elbows are perfect for permanent assembly on processing systems that require a change of fluid direction. These fittings require robust welding for installation that offers high integrity and durability in applications that require longevity and cleaning in place (CIP).

Monel 400 is a Nickel-Copper alloy, resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.

Hastelloy C-276 alloy excellent resistance to a wide variety of chemical process environments such as chlorine, formic and acetic acids, acetic anhydride, and seawater and brine solutions.

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.?Butt-weld and forged fittings are available.Excellent corrosion resistance in many acidic and alkaline environments Especially suitable for reducing conditions. Good ductility and thermal conductivity Ideal for seawater applications.

Super Duplex 2507 Equal tees are the most common fittings.

Alloy 800HT / Incoloy 800HT is a controlled composition derivative of INCOLOY alloy 800H (UNS N08810) and is used for the same creep resistant applications, however the combined effects of mechanical and thermal processing of the alloy permit higher design stresses to be incorporated than are permitted for the conventional alloy.

It is not useful in oxidizing acids, such as nitric acid and nitrous.

ASTM B366 UNS N08800 Butt Welded Pipe Fittings belong to a small class of superalloyed austenitic stainless steel components. These fittings are designed with nickel, iron and chromium compositions and play an important role in influencing the flow characteristics in the system. These modules can be used to redirect, split or connect different components in a piping system.

Alloys 800, 800H and 800HT are nickel-iron-chromium alloys with good strength and excellent resistance to oxidation and carburization at high temperature exposure.

Stainless steel tees are used to connect 3 pipes and join them into 1 to mix fluids. Whereas steel reducers are used to reduce the diameter of pipes. Stainless steel welded pipe fittings have a melting point of 1400 degrees Celsius and an operating temperature of 870 degrees Celsius.

Duplex Steel S31803 Reducer Fittings are resistant to chloride environments and sulfide stress corrosion. Our WNR 1.4462 Duplex Steel S31803 Pipe Couplings withstand sulphur-induced stress corrosion cracking, accommodate high steam pressures and provide extended service life, economical and reliable.

Nickel 800H reducing butt welded pipe fittings are also used in heat exchangers, dampers, pressure vessels, etc. Our Alloy 800HT Elbow Butt Weld Fittings can also be used in industrial furnaces and heat treating equipment.

Grade 430 is a ferritic, straight chromium, non-hardenable grade, combining good corrosion resistance and formability characteristics with useful mechanical properties. Its ability to resist nitric acid attack permits its use in specific chemical applications but automotive trim and appliance components represents its largest fields of application.

Sanitary pipe fittings AISI304, AISI304L, AISI316, AISI316L, its standard is DIN/SMS/3A/ISO/IDF, pipeline flow control: DN10-DN200&1 /4″”-8″, it is used in stainless steel pipe system, its working principle It can be welded on the pipeline to adjust the flow in the pipeline. Its medium includes beer, dairy products, beverages and pharmaceuticals.

Inconel 600 alloy is arguably a standard engineering material used in a variety of applications requiring high temperature and corrosion resistance. Inconel 600 fittings have some excellent mechanical properties and are popular for their enhanced strength and high workability. Due to its chemical composition, the material possesses all these excellent properties. It contains high concentrations of various important elements such as chromium, molybdenum and nickel. It also shows good antioxidant properties.

Inconel600 is suitable for welding with the same material or other metals by any traditional welding process, such as tungsten electrode inert gas welding, plasma arc welding, manual sub-arc welding, metal inert gas shielded welding, molten arc inert gas shielded welding, and pulsed arc welding. Welding is the preferred solution. When using manual arc welding, it is recommended to use a shielding gas mixed with various components (Ar+He+H2+CO2).
Welding of Incoloy 825 must be carried out in the annealed condition and cleaned with a stainless steel wire brush to remove stains, dust and various markings. When welding the root of the weld, extreme care must be taken (Argon 99.99) to obtain the best quality of the root weld so that the weld does not produce oxides after the root has been welded. Color from the weld heat-affected zone should be removed with a stainless steel brush while the weld area is not cool.

Inconel 601 (UNS N06601 ) nickel-based alloy density: 8.42 g/cm3 (grams/cubic centimeter).

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.?Butt-weld and forged fittings are available.Excellent corrosion resistance in many acidic and alkaline environments Especially suitable for reducing conditions. Good ductility and thermal conductivity Ideal for seawater applications.

We are a manufacturer, trader, stocker, supplier and exporter of alloy 20 pipe fittings made from niobium stabilized austenitic pipe fittings that minimize carbon induced carbide precipitation during welding.

Monel 400 works in a range of acidic and alkaline environments and features excellent ductility and thermal conductivity.

Hastelloy’s resistance to sulfuric acid makes it a common choice for protection from hydrogen sulfide (H2S), more commonly known as?sour gas.

As a butt weld fitting, it works with lap flanges. The use of stainless steel short pipe ends and lap flanges can effectively reduce pipeline maintenance costs. In stainless steel piping systems or advanced systems, we can choose low-grade lap flanges with stainless steel short pipe ends as an alternative to flanged connections instead of butt-welded flanges, effectively reducing manufacturing costs.

Butt weld tee dimensions shall be specified in pipe NPS (DN) and thickness in schedule, where socket weld tee or threaded tee thickness specified in pressure class ratings.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

ASTM A234 WPB Pipe Fittings belong to a group of pipes and fittings that are intended for moderate to high temperature services with pressure piping. The A234 is the specification for the moderate to high temperature services where the WPB stands for grade B pressure and weldable pipes.

We are a manufacturer, trader, stocker, supplier and exporter of a full range of Duplex Steel S31803, S32205 Pipe Fittings made of 50-50 Austenitic-Ferritic microstructure with excellent impact toughness and higher resistance to general corrosion.

These Duplex Steel UNS S31803 Butt Weld Fittings are manufactured by maintaining quality. Our experts first select raw materials using the latest tools and services, then manufacture. We always follow national and international standards and codes to maintain the quality standards of these duplex steel fittings.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

ASTM A403 WP317 Pipe Fittings?could be a altered adaptation of?Stainless Steel 317L Pipe Fittings.

Duplex 2507 possesses excellent mechanical properties. Often a light gauge of 2507 material can be used to achieve the same design strength of a thicker nickel alloy. The resulting savings in weight can dramatically reduce the overall cost of fabrication.