ASTM B164 UNS N04400 monel400 1.4301 round bar

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.

ANSI B 16.47 Monel DIN 2.4375 Threaded Flanges are welded to a pipe or fitting with a single full penetration. ASTM B 564 Monel K500 Lap Joint Flanges may be used at all pressures and are available in a full- size range. They can be salvaged for use in systems that erode or corrode quickly. We keep a tab on market trends and demands, to invent new, sustainable and economical products capable of undergoing customization. Our products are fully certified and 100% durable.

Monel 400 is a nickel-copper alloy of about 67% Ni and 23% Cu.

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with excellent corrosion resistance in a wide range of marine and chemical environments and has freedom from chloride induced stress-corrosion cracking.

The superposition of residual stress caused by cold working and aging thermal stress, as well as the preferential embrittlement of the surface layer at the initial stage of aging, are the main reasons for aging cracking of Monel K500 alloy.

Monel 400 flanges are a nickel-copper alloy (approximately 67% Ni ¨C 23% Cu) resistant to seawater and steam at high temperatures, as well as salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold work. This nickel alloy has good corrosion resistance, good weldability and high strength.

Stronger than 400, alloy K500 washer even retains this strength in corrosive. conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas.

Monel 400 and K500 flanges also exhibit excellent corrosion resistance in marine applications and have reasonable corrosion resistance to sulfuric and hydrochloric acids under reducing conditions.

A nut is a fastener that runs through its inner radius. Nuts are used in combination with bolts to hold a virtually unlimited number of parts, objects and accessories for many types of applications. When Monel 400 alloy is used as a material for making nuts, benefits can be seen in the short and long term. Monel Nickel Copper 400 Nuts provide strength and corrosion resistance in both acidic and alkaline environments. Monel NiCu 400 nuts are also known for their favorable dimensional accuracy and non-corrosion in salt water and hydrofluoric acid.

The Asme B16.5 Inconel 600 Flange exhibits good resistance across a broad range of corrosive mediums. The chromium content in the Alloy 600 Flanges gives them better resistance as compared to both Alloy 200 as well as alloy 201 under oxidizing conditions. Also, These Monel K500 Flanges are technologically advanced under the direction of skilled specialists by making use of the premium quality of materials.

These pipes are difficult to machine because they harden from machining. Alloy 400 welded pipe can be processed using conventional techniques.

The alloy is slightly magnetic at room temperature. Monel 400 is widely used in the chemical, oil and marine industries.

The Monel 400 alloy is also known as super alloy monel. This alloy is available in some standard shapes such as hexagon, round, tube, pipe, plate, strip, sheet and wire.

Spring washers are locking washers that are used when there is a need to prevent a fastener from loosening as a result of vibration. They are also often called split lock or split ring washers.

Alloy K500 has approximately three (3) times the yield strength and double the tensile strength when compared with 400. MONEL K500 can be further strengthened by cold working before the precipitation hardening.

While it is a very useful metal, it is cost prohibitive in most applications. Monel 400 costs 5 to 10 times as much as regular nickel or copper.

Monel nickel-copper alloy K-500 pipe bend and elbow combine the excellent corrosion resistance characteristic of Monel alloy 400 with the added advantages of greater strength and hardness.

A high nickel alloy with the addition of substantial amounts of copper to give the alloy excellent resistance to sodium chloride solutions, including brine and seawater. Therefore, UNS N04400 Alloy 400 Forged Fittings and Socket Weld Elbows can be used as part of an offshore piping system that may require a change of direction.

In fact, in comparison to nickel, the corrosion resistance properties of UNS N04400 Orifice Flange tend to be much higher than nickel itself.

Monel 400 also resistant to corrosion of neutral solution, water, sea water, atmosphere and organic compounds.

ASTM B564 UNS N04400 Pipe Flang Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

The Curie temperature of this alloy lies within the ambient temperature range and is affected by changes in the alloy’s chemical composition. Caution is recommended in applications requiring strong non-magnetic properties.

UNS N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

ASTM B564 Monel K500 Flanges, ANSI B16.5 Monel DIN 2.4360 Socket weld Flanges, ASTM B564 Monel 400 Threaded Flange, Monel 400 Weld Neck Flanges Supplier, ASME SB564 Monel DIN 2.4375 RTJ Flanges, Monel UNS N04400 Orifice Flanges, K500 Alloy Forged Flanges Exporter, Monel 400 Lap Joint Flanges Distributor

The high-temperature plasticity of the experimental alloy added with trace amounts of Mg, Cr and Co is obviously improved, and it exhibits certain superplasticity. At 1010¡æ, the strain rate sensitivity index m is 0.32, and the maximum elongation is 240%.

Monel K500 bolts and nuts are used in a variety of industries due to their high temperature resistance, high corrosion resistance and durability. It is a nickel-copper alloy with a composition of 63% nickel and 27% copper, among other elements. HT PIPE is a leading manufacturer of Monel K500 Bolts and Nuts of all types and sizes. Fastener applications include the offshore petroleum industry, power plant applications, petrochemicals, gas handling units, specialty chemicals, pharmaceuticals, equipment, seawater applications, heat exchangers, condensers, and the pulp and paper industry.

Alloy 400 Pipe Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

MONEL? alloy K-500 (UNS N05500 / W.Nr. 2.4375) is a nickel-copper alloy which combines the excellent corrosion resistance of MONEL alloy 400 with the added advantages of greater strength and hardness. The increased properties are obtained by adding aluminum and titanium to the nickel-copper base.

Alloy 400 Seamless Tubing has good ductility which helps to shape and form easily & are available in flat oval, elliptical, round, rectangular & square shapes with 0.030 in. to 1.250 in. OD, 0.008 in. ID & 0.003 in. to 0.280 in. wall thickness.

Monel 400 and K500 nuts also exhibit excellent corrosion resistance in marine applications and have reasonable corrosion resistance to sulfuric and hydrochloric acids under reducing conditions. A standout feature of monel nuts is their excellent resistance to hydrofluoric acid, a particularly difficult acid to handle, at all concentrations up to the boiling point. For hydrofluoric acid applications, Monel nuts are probably the most corrosion resistant of all commonly used specialty alloys.