ASTM B366 N04400 Concentric Reducer Fittings

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

But since the chief alloyant in the ASTM B564 UNS N04400 SORF Flange is nickel, the resistance to these particular reductive solutions is strong.

It is resistant to most alkalis, salts, waters, food products, organic substances and atmospheric conditions at normal and elevated temperatures.

A finished hex nut, also known as a standard hex nut, has a smaller width across the flats and corners compared to a heavy hex nut. Heavy hex nuts are thicker and heavier in weight. The proof load strength is higher than a standard hex nut. Heavy hex nuts provide increased bearing surface area over finished nuts.

One of the most important characteristics of Monel 400 is that stress corrosion cracks do not occur in general, and the cutting performance is good. The structure of Monel 400 is single phase solid solution with high strength.

Alloy 400 Blind Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Also known as alloy K500, Monel K500 bolts are comprised of a nickel alloy that combines the outstanding corrosion resistance of Monel 400 with increased strength and hardness.

We offers the complete range of Monel Flanges including Slip on, socket weld, blind, lapped, screwed, weld neck, reducing etc.

NAS625 (NCF625, UNS N06625) is a nickel-chromium-molybdenum alloy with an additional of niobium. Matrix stiffening provided by molybdenum and niobium results in high strength. The alloy resists a wide range of severe corrosion environments. It also offers resistance to high temperatures. It also demonstrates remarkable protection against corrosion and oxidation. Its ability to withstand high stress and a wide range of temperatures, both in and out of water, as well as being able to resist corrosion while being exposed to highly acidic environments makes it a fitting choice for nuclear and marine applications.

The Monel K500 flanges available in our company are customized in designs, sizes and shapes. The specification of these flanges is ASTM B564. These flanges range in size from 1/8 inches to 48 inches.

MONEL K500 is a nickel-copper alloy, precipitation hardenable through additions of aluminum and titanium.

The high-temperature plasticity of the experimental alloy added with trace amounts of Mg, Cr and Co is obviously improved, and it exhibits certain superplasticity. At 1010¡æ, the strain rate sensitivity index m is 0.32, and the maximum elongation is 240%.

ASTM B564 UNS N04400 Pipe Flang Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

Monel 400 is a popular nickel-copper alloy commonly used in high performance applications. The alloy has high resistance to acidic and alkaline environments, high strength, good ductility and thermal conductivity. Monel 400® is suitable for use in the subzero to 1,000°F (538°C) temperature range and can only be hardened by cold work.

The Alloy 400 Orifice Flange is a special type that is used to fit pipes together with an orifice. The minimum yield strength of the material is at 195MPa and the minimum tensile strength is 480MPa.

The classes define the pressure capacities. The monel 400 flanges have 63% nickel and 28% copper in the composition which makes them stronger.

MONEL K500 is non-magnetic. MONEL K500 should be annealed when welded and the weldment then stress relieved before aging.

Monel K500 fasteners also have some excellent seawater resistance for marine applications. Monel fasteners also have some high-strength metals that have good toughness at high temperatures.

Nimonic 80 a (Alloy 80A) is one of the most popular superalloys specified for gas turbines. Nimonic 80A fasteners are often specified because of their ability to withstand very high temperatures. This makes Nimonic bolts and nuts ideal for use in aircraft parts and custom-designed gas turbine components, from turbine blade mounting to exhaust nozzles on jet engines, where Nimonic fasteners are exposed to very high levels of pressure and heat.

Monel 400 flanges are a nickel-copper alloy (approximately 67% Ni ¨C 23% Cu) resistant to seawater and steam at high temperatures, as well as salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold work. This nickel alloy has good corrosion resistance, good weldability and high strength.

MONEL K500 conserva las excelentes propiedades de resistencia a la corrosion de 400, con mayor resistencia y dureza despues del endurecimiento por precipitacion en comparacion con 400.

Monel400 alloy is a versatile material that can be used in many industrial applications

This nickel alloy is particularly resistant to hydrochloric and hydrofluoric acids when they are de-aerated. As would be expected from its high copper content, alloy 400 is rapidly attacked by nitric acid and ammonia systems.

We are a maker, broker, stockist, provider and exporter of ASME SB564 Monel K500 Flanges which are precipitation solidified, high in quality ribs, yielding a rigidity of 115 ksi for a power pressed execution. Monel K500 fasteners and flanges offer a unique combination of high strength with similar corrosion resistance to Monel 400 and improved resistance to a sour-gas environments.

Generally, its corrosion resistance is very good in reducing environments, but poor in oxidizing conditions.

Monel 400 is a popular, high performance nickel-copper alloy commonly used in critical and high performance applications.

ASME SB564 Monel UNS N04400 Weld Neck Flanges are utilised in pharmaceutical equipment, heat exchangers, condensers, power generation, etc. ANSI B 16.47 Monel DIN 2.4375 Threaded Flanges are welded to a pipe or fitting with a single full penetration. HT PIPE takes ultimate pride in offering the above mentioned range of products that fall under the Monel Flanges product type that come in two grades, 400 and K500. Also We offer wide range of Monel ASTM B564 400 Flanges such as Monel 400 Slip On Flanges, Monel K500 Weld Neck Flanges.

There are different standards to cover the different nominal bore sizes of the flanges. The ANSI B16.5 Monel DIN 2.4360 Blind Flange that has diameters ranging from ? inches to 48 inches in this standard.

From a human health perspective, the Nickel 400 Spectacle Blind Flange, which is used to clean, inspect or modify piping systems is effective in completely blocking or sealing off pressure vessels that could contain hydrofluoric acid, which again, is a contact poison.

Alloy K500 is refined by Electroslag Refining (ESR), ensuring the cleanest and highest quality material. This increased alloy purity limits the potential for hard non-metallic inclusions that can increase machining difficulty, machining time and ultimately lead to part failure. It also has low permeability and is non-magnetic at temperatures as low as -150¡ãF (-101¡ãC).

We manufacture Monel K500 flanges from nickel and copper alloys. The material has excellent resistance to aggressive materials and solutions such as oxidizing salts, acids, nitrates and other oxidizing agents.