ASTM B366 UNS N10276 UNS N10665 UNS N10675 90 deg ELBOW ASME B16.9 pipe fitting butt weld elbows

Another key feature of duplex stainless steel is its enhanced corrosion resistance. Due to its higher strength, longer component life cycle and lower alloy composition, duplex stainless steels can be a very cost-effective solution to engineering problems.

Monel K500 has about three times the yield strength and twice the tensile strength of Monel 400, and higher mechanical properties can be obtained by cold working or age hardening. Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.

2205 is the most widely used duplex (ferritic/austenitic) stainless steel pipe fittings. It is used due to its excellent corrosion resistance and high strength. Duplex S31803 fittings offer a better guarantee of corrosion resistance, but most duplex S31803 currently produced also complies with duplex S31803. 1.4462 belongs to the DUPLEX steel series. This steel has higher corrosion resistance than eg austenitic 1.4404. Therefore, the tensile yield point is about 150% higher.

Applications in the chemical process industry involving sulfuric, phosphoric, hydrochloric and acetic acid.

We offer a wide range of stainless steel 904l buttweld fittings such as ANSI B16.9 Stainless Steel 904L Buttweld Elbow, 904L Stainless Steel Buttweld Reducer, Stainless Steel UNS N08904 Buttweld Fittings, Stainless Steel 904L Buttweld Tees, B366 Stainless Steel 904L Long Radius Bend Pipe Fittings, 904L Stainless Steel Buttweld 90 deg Elbow, Stainless Steel DIN 1.4539 Pipe Fittings, 904L Stainless Steel Buttweld End Pipe Cap. etc. These stainless steel 904l buttweld fittings are available in various sizes, shapes as per the requirements of our clients.

The increased properties are obtained by adding aluminum and titanimum to the nickel-copper base, and by heating under controlled conditions so that submicroscopic particles of Ni3 (Ti, Al) are precipitated thoughout the matrix.

These pipe fittings include Tee, Concentric reducer, eccentric Reducer, 5D/6D bend, elbow, unions, plugs, cross tee, pipe cap and nipple, ect for use in pressure piping and in pressure vessel fabrication for service at moderate and elevated temperatures.

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.?Butt-weld and forged fittings are available.Excellent corrosion resistance in many acidic and alkaline environments Especially suitable for reducing conditions. Good ductility and thermal conductivity Ideal for seawater applications.

Duplex 2205 fittings have higher tensile strength than standard austenitic stainless grades. This means buyers can choose the Duplex SS 2205 butt joint with a thinner cross-section and lighter weight. 2205 Duplex Fitting is a two-phase ferritic, 3% molybdenum, austenitic 22% chromium, 5% to 6% nickel alloy stainless steel. It is primarily used in duplex grades, which are characterized by a high yield strength that is twice that of standard austenitic grades. Both nickel and molybdenum are low in SA815 material.

Duplex S31803 Disc Lid Fittings are almost never used above 300 degrees Celsius. Duplex steel S31803 bent butt welded pipe fittings generally perform well in environments that cause premature failure of austenitic grades. Although duplex steel S31803 short end butt welded pipe fittings have good high temperature oxidation resistance, this grade – like other duplex stainless steels – can embrittle even for short periods of time if held at temperatures above 300 degrees Celsius. If embrittled, duplex S31803 end caps can only be corrected by full solution annealing. Duplex S31803 Disc Lid Fittings are almost never used above 300 degrees Celsius.

Alloy 20 is also known as UNS N08020 which is a stainless steel grade containing high alloy with excellent resistance to stress corrosion and sulfuric acid. This alloy grade contains various elements like copper, nickel; chromium and molybdenum that together help in offering crevice corrosion, resistance to corrosion and pitting.

Our SS 310S pipe fittings are made of low carbon austenitic steel known for its ability to resist corrosion, especially water corrosion and sulfidation in chemical and ore processing units.

All ASTM A234 Elbow & Elbow A234 Wpc are manufactured from plate, pressed in two halves with two weld seams. We offer 100% radiography on all welds as standard.

Hastelloy C-276 pipe fittings refer to factory-made wrought nickel alloy fittings manufactured to ASTM B366 UNS N10276. It can be designated as CRHC276(corrosion resistant fittings) or WPHC276(ASME pressure fittings). The fittings can be manufactured from pipe or tube of ASTM B619, B622, B626 UNS N10276, plate, sheet or strip of ASTM B575 UNS N10276, forging or bar of ASTM B564, B462, B472, B574 Gr. N10276. The Hastelloy C-276 fittings are mainly furnished in 3 connection types: butt welding, threaded, socket welding, covering a variety of standard specifications.

Being a two ¨C phase material (austenitic ¨C ferritic) stainless Steel BW Pipe Fittings will present a different tool wear profile from that of single ¨C phase steels of type 304L.

Duplex UNS S31803 Tee Fittings have high general corrosion resistance. Duplex UNS S31803 Cross Fittings provide good weldability in thick plates. Duplex UNS S31803 Reducer Fitting is a duplex stainless steel with a 50/50 austenitic, ferritic microstructure.

Stainless Steel Pipe Bends are resistant to atmospheric corrosion and prevent the internal fluid from getting contaminated.

254 SMO is a high-alloy austenitic stainless steel developed for use in seawater and other corrosive chlorine-containing media. The steel has the following characteristics: excellent resistance to pitting and crevice corrosion, high resistance to general corrosion, high resistance to stress corrosion cracking, higher strength than conventional austenitic stainless steels, and good weldability.

Fittings such as ASTM A815 UNS S32205 Long Radius Elbows are used in seawater, marine and highly corrosive applications such as the oil, oil and gas, and offshore oil drilling industries because the duplex material is strong and resistant to corrosion by acid and chloride ions.

Duplex steels are stainless steels, also known as duplex steels due to the presence of two phases in their metallurgical structure. This duplex steel is designed to provide better corrosion resistance and higher strength than other aesthetic stainless steels.

A pipe tee is a sort of pipe connection that is T-shaped and has two outputs that are 90¡ã to the mainline connection. It’s a small section of pipe having a side exit. Pipe Tees are being used to join pipes by forming a 90-degree location also with streams.

SA234 WPB Elbow is made up of carbon steel or alloy steel.

Pipe Tee is a type of pipe fitting which is T-shaped having two outlets, at 90¡ã to the connection to the main line. It is a short piece of pipe with a lateral outlet. Pipe Tee is used to connect pipelines with a pipe at a right angle with the line. Pipe Tees are widely used as pipe fittings.

In fact, the above properties of 317L fittings are considered to be much better than traditionally used stainless grades such as 304, 304L, 316 and 316L. The alloys used for stainless steel 317L are known to provide better resistance than 316L, especially in highly corrosive environments, which may contain chemicals such as sulfur-containing media, chlorides and other halides.

Stainless Steel 904L Buttweld and Forged Fitting have exceptional quality completing and coercion for long life, high weight. Stainless Steel 904L Buttweld and Forged Fitting are fabricated to support high weight and item guarantee. Stainless Steel 904L Buttweld and Forged Fitting in the type of Bend, Elbow, Tee, Reducer, Cap, Stubend, Nipple, Union, Cross, Coupling, Socket, Plug, Sockolet, Weldolet, Threadolet, Elbolet, Nipolet Etc.

The 304 elbow is a stainless steel threaded pipe fitting that changes the direction of the pipeline in the pipeline system. According to the angle, there are 45 ¡ã and 90 ¡ã. In addition, according to engineering needs, it also includes other abnormal angles such as 60 ¡ã. The material of our threaded elbows is 304 stainless steel.

These Duplex Steel UNS S31803 Butt Weld Fittings are manufactured by maintaining quality. Our experts first select raw materials using the latest tools and services, then manufacture. We always follow national and international standards and codes to maintain the quality standards of these duplex steel fittings.

Type 317L is a molybdenum-containing austenitic stainless steel intended to provide improved corrosion resistance relative to Type 316L in highly corrosive process environments, particularly those containing chlorides or other halides. The low carbon permits Type 317L to be welded without sensitization to intergranular corrosion resulting from chromium carbide precipitation in the grain boundaries. Type 317L is non-magnetic in the annealed condition but may become slightly magnetic as a result of welding.

Super Duplex 2507 (F53 / 1.4410 / UNS S32750) has excellent corrosion resistance to a variety of media, and has excellent resistance to pitting and crevice corrosion in seawater and other chloride-containing environments, with a critical pitting temperature exceeding 50¡ãC.

Stainless steel such as 304 and 316L casting of pipe fittings requires low maintenance and does not need an additional coating, in both indoor and outdoor applications. The expected lifetime of a stainless steel pipe fitting is more than 50 years, reducing system down time, replacement and maintenance costs over the life of the installation.