ASTM B366 WPHC22 nickel alloy pipe fittings

Hex bolts are used to fasten two or more parts together to form an assembly either because it cannot be manufactured as a single part or to allow for maintenance and repair disassembly. By definition “A Bolt is a headed and externally threaded mechanical device designed for insertion through holes in assembled parts to mate with a nut and is normally intended to be tightened or released by turning that nut.” When used with a preformed internally threaded (tapped) hole, the hex bolt’s head is turned to tighten, which technically makes it a screw (see our Tech Data section for a discussion regarding the differences between bolts and screws). Hex bolts are also known as: hex head bolts, cap screws, hex cap screws, hex head cap screws, machine bolts, hex machine bolts, hex head machine bolts and, if fully threaded, tap bolts, hex tap bolts and hex head tap bolts. A hex bolt is often differentiated from a hex cap screw by its underhead bearing surface: if it has a circular boss, called a washer face, it’s a hex cap screw¡ªif it doesn’t then it’s a hex bolt.

The dual-phase steel S31803/S32205 reducer suppresses deformation and cracking at high temperature, which is superior to ordinary steel parts in the chemical industry that are sensitive to chloride stress corrosion cracking.

Hastelloy C-276 pipe fittings refer to factory-made wrought nickel alloy fittings manufactured to ASTM B366 UNS N10276. It can be designated as CRHC276(corrosion resistant fittings) or WPHC276(ASME pressure fittings). The fittings can be manufactured from pipe or tube of ASTM B619, B622, B626 UNS N10276, plate, sheet or strip of ASTM B575 UNS N10276, forging or bar of ASTM B564, B462, B472, B574 Gr. N10276. The Hastelloy C-276 fittings are mainly furnished in 3 connection types: butt welding, threaded, socket welding, covering a variety of standard specifications.
Since Alloy C-276 contains a high amount of nickel in its chemical composition, the metal is very ductile. Therefore forming it into various shaped Hastelloy C276 Pipe Fittings becomes very simple. Yet, this is not the only benefit offered by this alloy. Like many nickel containing alloys, the strength and corrosion resistance properties of this alloy make it one of the most sought after ones by Hastelloy Fittings Suppliers. The metal is capable of exhibiting superior resistance to pitting. Unlike highly ductile materials that tend to exhibit failure against stress corrosion cracking, on the application of a tensile load, the Alloy C276 Pipe Fittings are able to withstand such levels of stress.

Butt weld elbows in the Incoloy 825 series are one of the strongest and most versatile elbows types. These fittings can be easily attached to pipe because they have beveled ends that meet ASME B16.25. These elbows allow the module to create full penetration welds without any additional penetration or preparation. The fittings are welded according to the butt welding procedure, placing them on the assembly and welding in place. Welded connections in this range provide a strong and high-strength connection. These fittings are available in larger and stronger sizes compared to other grades of fittings.

Monelk500, also known as UNS N05500, has the same corrosion resistance as monel400, but has higher mechanical strength and hardness. It has good corrosion resistance and long-term organizational stability.

Available in a variety of thread types and sizes, head types and lengths, our SS UNS S31600 Pipe Elbow is used to shield all types of pipe from dirt and moisture penetrating the interior of the pipe. Stainless steel 316 butt welded pipe fittings are highly resistant to corrosive activity and carbide precipitation, primarily due to the addition of molybdenum.

Monel K500 pipe bend and elbow are resistant to a sour-gas environment

ASTM A860 WPHY 46 are Wrought High Yield fittings and are generally used at High-pressure requirements. A860 refers to the high strength of the fittings. ASTM A860 WPHY 46 Pipe Fittings are known for high tensile strength and corrosion resistance. Available in numerous specifications, these ASTM A860 Fittings are manufactured with high-grade steel & tested by a quality expertise team.

Stainless steel 347 reducer has tensile strength and minimum yield strength. Stainless Steel 347 Stub End Fittings are a non-magnetic grade that cannot be hardened by heat treatment, are typically used in the annealed condition, and are known for their ease of fabrication and formability.

Two criteria for evaluating oxidation resistance are weight change and depth of corrosion penetration. HASTELLOY X pipe bend excels in both respects due to the formation of a protective, tenacious oxide film.

It is even resistant to strong liquids such as sulfuric acid, wet chlorine gas, chloride solutions, hydrochloric acid and most organic acids. However, it can burn in air and is the only element that will burn in the presence of nitrogen.

ASTM A420 WPL6 Pipe Fittings such as WPL6 Caps, A420 WPL6 Weld Fittings, and SA 420 WPL6 Elbow. Our stock of low temperature steel fittings includes A420 Grade WPL6 fittings in a complete range of sizes and thicknesses.

Traditionally, duplex steels have a chromium content of about 22% by weight. Likewise, stainless grade 2205 is a duplex stainless steel with 22% chromium in the alloy. The higher chromium content in Duplex 2205 fittings provides several benefits, including higher yield strength, better mechanical properties, and excellent corrosion resistance.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Stainless steel 304 pipe fittings contain both chromium 18% – 20% and nickel 8% – 10.5%. It is an austenitic stainless steel and is less electrically and thermally conductive than carbon steel. It is a component that helps in change the direction of the flow such as tees and pipe bends.

Werkstoff No.1.4436 316 stainless steel fittings are resistant to atmospheric corrosion, as well as moderately oxidizing and reducing environments. Corrosion resistant in polluted marine atmospheres. It has excellent resistance to intergranular corrosion.

The austenitic structure of 316 stainless steel provides excellent toughness even at low temperatures.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

A860 WPHY 42 Pipe Fittings are a pre-requisite for the conveyance of gas and oil in the high-pressure gas and oil transportation systems.

Alloy X pipe bend is one of the most widely used nickel base superalloys for gas turbine engine components.

Duplex Steel 2101 Butt Weld Pipe Fittings, which is the most widely used duplex (ferritic & austenitic) stainless steel grade made at par with the international quality standards making use of high-grade steel.?Duplex?Steel 2101 Pipe Fittings?are extremely corrosion resistant and work hardenable alloys.?Duplex Steel 2101 Buttweld Fitting?are almost never used above 300 Degree C.

HT PIPE is the government certified and doing business in steel industry for long years and are manufacturing S32750 Duplex buttweld fittings at affordable rates.

UNS S31803 offers class-leading excellence, durability, excess energy and corrosion resistance. Our clean production process, absolute green factory, excellent metal raw materials and professional panels, provide a wide range of high-quality solid accessories.

It is used in flue gas desulfurizations systems because of its excellent resistance to sulfur compounds and chloride ions encountered in most scrubbers. C-276 alloy has excellent resistance to pitting and to stress- corrosion cracking.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

304 stainless steel is the most common stainless steel. The steel contains both chromium (between 18% and 20%) and nickel (between 8% and 10.5%)[1] metals as the main non-iron constituents. It is an austenitic stainless steel.When it comes to uses, SS304 can be found in kitchen sinks and other appliances such as toasters and microwave ovens. SS304 is also used to make pressure vessels, wheel covers as well as for building facades.

Fittings are used to change the direction of the pipe. The easiest way is to bend the pipe. However, it stretches and thins the outer wall of the pipe. It also thickens the inner walls of the pipe. 2205 duplex stainless steel fittings are known for their austenitic and ferritic microstructures. They show the properties of both classes. ASME SA815 Duplex Steel Butt Welded Pipe Fittings show improved localized corrosion resistance compared to Grades 316 and 317.

The higher strength results from deliberate control of the carbon, aluminum, and titanium contents in conjunction with a high-temperature anneal.

Our high quality standard grade 150 lb 304 316 stainless steel threaded fittings are manufactured to the highest standards. All stainless steel pipe fittings are monitored by quality control personnel for strict adherence to applicable standards and codes. These stainless steel fittings are ideal for applications involving potentially corrosive chemicals or liquids. In addition to being resistant to corrosion, stainless steel pipe fittings also prevent contamination, making them useful for many professionals.

Stainless steel pipe fittings are used to connect 2 pipes as they have a pipe fitting at one or both ends. The stainless steel reducing tee has a tensile strength of 515 MPa and a yield strength of 205 MPa.