ASTM B564 Hastelloy Alloy X Flange Manufacturer and supplier in China

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

Hastelloy C2000 lap joint flanges are used for heat treatment applications. They have very little carbon content and high nickel content, which makes them much stronger than any other flanges.

Hastelloy C276 has a low carbon content to minimize grain boundary carbide precipitation during welding to maintain corrosion resistance in the heat affected zone of the welded joint

These also enhances good resistance to pitting and crevice corrosion in tough climatic circumstances. These alloys of flanges also possess superior thermal conductivity and electrical resistivity.

HASTELLOY X pipe bend is recommended especially for use in furnace applications because it has unusual resistance to oxidizing, reducing, and neutral atmospheres.

The pipes are having good stress corrosion cracking and pitting resistance ability.

Hastelloy fasteners such as bolts, screws, nuts and threaded rods are ideal for use in a variety of moderately to severely corrosive acid environments. The most common grade of Hastelloy fasteners is Hastelloy C276 (2.4819), which is one of the most versatile corrosion-resistant nickel alloys, surpassing Inconel or Monel. There are also other special grades of Hastelloy fasteners that can address more niche corrosion problems.

This alloy is exhibiting good corrosion resistance at aggressive reducing media like hydrochloric acid that range of concentrations and temperatures and in medium-concentrated sulphuric acid and with limited chloride contamination.

Nickel alloys are some of the most useful materials for manufacturing technically superior pipes and tubes for industrial applications.Nickel Pipe is a metal pipe that is made up of an alloy that has primarily nickel and other elements in its composition.

Alloy N10675 is a high corrosion resistant nickel molybdenum Alloy. This alloy is characterized by a high resistance against hydrochloric acid and other reducing media in a wide range of temperature and concentration.

Hastelloy C22 fasteners are a general-purpose grade composed of chromium, nickel, molybdenum and tungsten alloys. These designs are designed to increase resistance to pitting, stress corrosion cracking (SSC) and crevice corrosion cracking. It has high chromium content and good resistance to oxidizing media. The presence of molybdenum and tungsten provides good resistance to reducing media. Its nickel content provides admirable resistance to oxidizing aqueous media.

Other corrosives Hastelloy C-22 has resistance to are oxidizing acid chlorides, wet chlorine, formic and acetic acids, ferric and cupric chlorides, sea water, brine and many mixed or contaminated chemical solutions, both organic and inorganic.

It is used in flue gas desulfurization systems because of its excellent resistance to sulfur compounds and chloride ions encounted in most scrubbers. C 276 alloy has excellent resistance to pitting and to stress corrosion cracking. It is also one of the few materials that withstands the corrosive effects of wet chlorine gas, hypochlorite, and chlorine dioxide.

Hastelloy C276 alloy has excellent resistance to a variety of chemical process environments, including strong oxidizing agents (such as ferric chloride and cupric chloride), hot fouling media (organic and inorganic), chlorine, formic and acetic acid, acetic anhydride, and seawater and saline solution. In fact, these Hastelloy c276 fasteners can be used in oxidizing atmospheres up to 1900¡ãF. Additionally, Hastelloy c276 hex bolts tend to perform extremely well in high pressure environments. For example, ASTM B574 bolts perform well at pressures around 5400 kPa during acid leaching.

Hastelloy C276 Sheets is a solid-solution-strengthened, nickel-molybdenum-chromium alloy with a small amount of tungsten, which exhibits excellent corrosion resistance in an assortment of harsh environments.

C276 is forged between 2250/1750oF (1230/955oC) and then soaked at the forging temperature for 30 minutes per inch of billet or ingot section thickness. Forging should begin immediately, the billet is removed from the reheat furnace, a 25/40% reduction helps retain as much internal heat as possible. For optimum corrosion resistance, forged parts should be subsequently annealed. See Heat Treatment.

Steel Plate are often used for structural and construction applications, pressure vessels, marine and offshord equipment, and military applications. The grade, elements and parameters of a steel plate are also important in how it is used.
Steel plates are classified by thickness: thin plate, medium plate, thick plate and extra-thick plate.
Thin steel plates are steel plates with a thickness between 0.2-4mm produced by hot rolling or cold rolling, and thick steel plates are those with a thickness of more than 4mm
The general name of the good board.
Thin steel plate refers to a steel plate with a thickness of not more than 3 mm. The commonly used thin steel plate thickness is 0.5-2MM, which is divided into sheet and coil supply. Thin
The steel plates are generally B-type steels, cold-rolled or hot-rolled steel plates with steel grades B0-B3. Requirements for thin steel plates: smooth, smooth surface, thick
The degree of uniformity, allowing a tight iron oxide film, must not have cracks, scarring and other defects. The process is divided into hot rolled sheet steel and cold rolled sheet
plate. Mainly used in Changlin Dongfeng fans, automobiles, electrical equipment, vehicles, agricultural machinery, containers, steel furniture, etc.
Thick steel plates refer to steel plates with a thickness greater than millimeters. Thick steel plate is divided into extra-thick steel plate and medium-thick steel plate.
Medium and heavy steel plates refer to steel plates with a thickness greater than 3 mm and less than 50 mm. Medium and thick steel plates are mainly used in shipbuilding, boilers, bridges
Armor and high-pressure vessel shells, etc.
Extra-thick steel plate refers to a steel plate with a thickness of not less than 50 mm. Extra-thick steel plates are mainly used in shipbuilding, boilers, bridges and high-pressure vessel shells
blog.

B3 Hastelloy Flanges has special chemistry designed to achieve high thermals stability than the Alloy B 2, performing in easier fabrication.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

UNS N10276 Sheets has excellent resistance to pitting corrosion, pressure corrosion cracking and a far higher resistance to crevice corrosion than steels of alloy.

Nickel alloys are alloys with nickel as principal element. Complete solid solubility exists between nickel and copper. Wide solubility ranges between iron, chromium, and nickel make possible many alloy combinations.Steel plates are often used for structural and construcation applications, pressure vessels, marine and off shore equipment, and military applications. The grade, elements and parameters of a steel plate are also improtant in how it is used.

These Hastelloy B2 Weld Neck Flanges should not be used in oxidizing media or where oxidizing contaminants are available in reducing media.

As most bent pipes do not alter the ends of the piping, pipe bends are often easy to implement within a processing system using standard welding processes, flanges, or other connection methods.

Hastelloy C276 is resistant to localized corrosion such as pitting and stress corrosion cracking.

Prefabrication can be of many different types and undertaken at many different scales, from fabrication of small components and sub-assemblies through to large welded and bolted assemblies requiring significant logistical challenge to transport to site

The Hastelloy stainless steel plates are having low-carbon they can also withstand to the corrosive effect of the wet chlorine gas, hypochlorite and chlorine dioxide.

This nickel alloy also offers optimum resistance to environments where reducing and oxidizing conditions are encountered in process streams. This is beneficial in multi- purpose plants where such ¡°upset¡± conditions occur frequently.

Hastelloy C276 Flanges Hastelloy C276 Flanges are made up of the nickel chromium molybdenum alloy that is called hastelloy. The composition includes 50.99% nickel, 14.5% chromium, 15% molybdenum and carbon, manganese, silicon, sulfur, cobalt, iron and phosphorus in it. The Hastelloy C276 Flanges have high melting point of 1370 degrees Celsius. This high melting point allows for higher operating temperatures of the flanges. The material also has 790MPa minimum tensile strength and 355MPa minimum yield strength.

The basic composition of Hastelloy C276 round bar alloy is chemically composed of three elements, which are nickel, molybdenum and chromium.

These salts may develop when hydrochloric acid comes in contact with iron and copper. Therefore, if this alloy is used in conjunction with iron or copper piping in a system containing hydrochloric acid, the presence of these salts could cause the alloy to fail prematurely.

Hastelloy B2 Flanges come under the ASTM B564 specification with sizes ranging from ? inches to 60 inches under different standards.