ASTM B564 MONEL K500 FLANGES SPECIFICATION

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Monel 400 (UNS N04400) is a nickel-copper alloy with optimum high strength and corrosion resistance. It is widely used in a variety of severe acidic and alkaline environments. Monel is also used in pipes.

We offers the complete range of Monel Flanges including Slip on, socket weld, blind, lapped, screwed, weld neck, reducing etc.

Monel K500 fasteners and flanges are virtually non-magnetic and spark resistant, even at temperatures down to -200¡ãF. At temperatures that could rise up to 550C in these mediums, the N06600 Raised Face Weld Neck Flange Ansi B16.5 has been shown to be one of the most resistant out of the other conventional alloys.

900# Steel Flanges Nickel Alloy Monel 400 Flange Bleed Ring the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

ASTM B564 UNS N04400 Slip on Flange A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

A standout feature of Monel flanges is their excellent resistance to hydrofluoric acid, a particularly difficult acid to handle, at all concentrations up to the boiling point.

Alloy 400 exhibits corrosion resistance to many reducing media.

Monel K500 Bolts, also known as Alloy K500, are composed of a nickel alloy that combines the excellent corrosion resistance of Monel 400 with increased strength and hardness. These additional properties of Monel K500 bolts are the result of an age hardening process in which aluminum and titanium are added to a nickel-copper matrix, which is then precipitated throughout. Compared to 400, this process increases the yield strength of K500 by a factor of approximately 3 (110ksi vs. 45ksi) and doubles the tensile strength (160ksi vs. 83ksi). Monel K500 bolts will maintain their strength down to 1200¡ãF and even maintain their ductility down to -400¡ãF.

MONEL K500 is non-magnetic. MONEL K500 should be annealed when welded and the weldment then stress relieved before aging.

The chemical composition of Monel K500 Nippo Flanges provides great resistance to a lot of corrosive environments, such as pitting, crevice corrosion, inter ¨C granular corrosion, and stress ¨C corrosion cracking. Monel K500 Spacer Flanges has useful resistance to boiling sulfuric acid up to 40 % concentration, to 60 % concentration at 176 Degree F and in all concentrations to 150 Degree F.

MONEL 400 solid solution alloy can be hardened by cold work, but can be hot worked or cold worked, then annealed into complex structures and welded using an appropriate welding process.

Monel K500 Spacer Flanges has useful resistance to boiling sulfuric acid up to 40 % concentration, to 60 % concentration at 176 Degree F and in all concentrations to 150 Degree F. Stronger than 400, alloy K500 even retains this strength in corrosive conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas. The exception being that Monel K500 fasteners can be more prone to stress-corrosion cracking in some environments than Monel 400.

Alloy 400 is a solid solution of gold that can only be hardened by cold work. The nickel alloy has good corrosion resistance, good weldability and high strength

MONEL K500 is a age-hardenable Nickel-Copper alloy which combines the corrosion resistance of Alloy 400 with high strength corrosion fatigue and erosion resistance.

Monel 400 has high strength and toughness over a wide temperature range and excellent resistance to many corrosive environments. The composition is shown in the Table below.

Monel K500 Washers have the same basic iron and carbon composition, but steel also contains a healthy dose of chromium that gives its famous corrosion resistance.

We offer W.Nr 2.4360 Monel 400 Male & Female Flanges to the oilfield fabrication, offshore and to petrochemical industries; our flanges are age hardened and are resistant to caustic solutions, seawater, and to chloride solutions and nitric acids, under oxidising and reducing temperatures. HT PIPE takes ultimate pride in offering the above mentioned range of products that fall under the Monel Flanges product type that come in two grades, 400 and K500. Also We offer wide range of Monel ASTM B564 400 Flanges such as Monel 400 Slip On Flanges, Monel K500 Weld Neck Flanges, Monel K500 Socket Weld Flanges, 400 Monel Alloy Blind Flanges, Alloy K500 Orifice Flanges, Monel 400 Spectacle Blind Flanges, Alloy K500 Screwed / Threaded Flanges, Monel Alloy 400 Reducing Flanges, Alloy K500 Ring Type Joint Flanges (RTJ) etc.

It is not useful in oxidizing acids, such as nitric acid and nitrous.

Monel 400 Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Monel K500, UNS N05500 (QQ-N-286), is a precipitation hardenable nickel-copper alloy that combines the corrosion resistance of Monel Alloy 400 with higher strength (more than 2x stronger) and hardness.

Monel 400 contains the same levels of nickel and copper as the natural nickel ore found.

Monel 400 Socket Weld Flanges have good weldability and moderate resistance to corrosive environments. Nickel 400 glasses blind flanges for terminating pipes or pipes are resistant to seawater and steam at high temperatures.

La aleacion K500 tiene aproximadamente tres (3) veces el limite elastico y el doble de la resistencia a la traccion de 400 en comparacion con 400. MONEL K500 se puede fortalecer aun mas mediante el trabajo en frio antes del endurecimiento por precipitacion.

The strength of Monel400 Cu-Ni alloy is low in the annealed state, so it exhibits a higher degree of strength in the rolled state.

The Stud Bolt is a threaded rod with 2 heavy hexagon nuts, while the Hex Bolt has a head with one nut. Nuts and head are both six sided. Bolts threading are defined in ASME B1.1 Unified Inch Screw Threads, (UN and UNR Thread Form). The most common thread is a symmetrical form with a V-profile. The included angle is 60¡ã. This form is widely used in the Unified thread (UN, UNC, UNF, UNRC, UNRF) form as the ISO / metric threads.

Monel K-500 (N05500) Bolts are manufactured by the cold heading and hot forming technologies in nominal diameters ranging from 1/8¡±- 3¡± (M3 ¨C M80). It can be in both USCS/Imperial and metric sizes.

Monel K500 steel bars are particularly suitable for centrifugal pumps in the marine industry. This is due to the properties of Monel N05500 hot rolled bar, namely high tensile strength and low corrosion rate in high velocity seawater.

Monel K500 pipe bend and elbow are exceptionally good dimensional stability.

This alloy is most commonly used in a range of environments from mildly oxidizing to neutral and moderately reducing conditions. Other areas of application for this material are marine environments and other non-oxidizing chloride solutions.

These flanges are designed to comply with International standards and specifications. Monel R405 offers about the same corrosion resistance as nickel but with higher maximum working pressures and temperatures and at a lower cost due to its superior ability to be machined.