ASTM B564 UNS N04400 Monel 400 nickel alloy flange Manufacturer of WNR 2.4360 Flange

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Alloy 400 Pipe Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Monel K500 Bolts, also known as Alloy K500, are composed of a nickel alloy that combines the excellent corrosion resistance of Monel 400 with increased strength and hardness. These additional properties of Monel K500 bolts are the result of an age hardening process in which aluminum and titanium are added to a nickel-copper matrix, which is then precipitated throughout. Compared to 400, this process increases the yield strength of K500 by a factor of approximately 3 (110ksi vs. 45ksi) and doubles the tensile strength (160ksi vs. 83ksi). Monel K500 bolts will maintain their strength down to 1200¡ãF and even maintain their ductility down to -400¡ãF.

It has good mechanical properties from subzero temperatures up to about 480C.

It exhibits excellent weldability and can withstand very large amounts of pressure and weight.

Alloy 400 Blind Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Monel K500 Flanges is further virtually nonmagnetic, even at quite low temperatures. This UNS N05500 Monel are available in various evaluations and sizes, shapes. We offer Monel K500 Blind Flanges that is a unique combination of high strength with similar corrosion resistance to Monel 400 and improved resistance to a sour-gas environments.

Inconel alloy is a family of nickel-chromium superalloys and a trademark of Special Metals Corporation. Inconel 601 is resistant to high-temperature oxidation. The alloy also has good resistance to aqueous corrosion, has high mechanical strength, and is readily formed, machined, and welded.

Monel K500 Fasteners are precipitation hardenable nickel and copper base alloy fasteners. These fasteners are developed for the excellent corrosion resistance adding with benefits of great hardness and strength.

MONEL K500 retains the excellent corrosion resistant characteristics of 400 and has enhanced strength and hardness after precipitation hardening when compared with 400.

Monel 400 is a flexible nickel (63% minimum) – copper (34% maximum) alloy retaining strength and toughness at low temperatures while still being effective at temperatures around 1000 degrees F.

Monel 400 has high strength and toughness over a wide temperature range and excellent resistance to many corrosive environments. The composition is shown in the Table below.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Nickel alloys are some of the most useful materials for manufacturing technically superior pipes and tubes for industrial applications. Their inherent properties make them viable for a wide range of uses. Nickel alloys are exceptionally corrosion resistant and can be used in high-temperature environments.

Monel 400 Socket Weld Flanges have good weldability and moderate resistance to corrosive environments. Nickel 400 glasses blind flanges for terminating pipes or pipes are resistant to seawater and steam at high temperatures.

The combination of very low corrosion rates in high-velocity sea water and high strength make alloy K-500 pipe bend and elbow particularly suitable for shafts of centrifugal pumps in marine service.

Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.

Also known as alloy K500, Monel K500 bolts are comprised of a nickel alloy that combines the outstanding corrosion resistance of Monel 400 with increased strength and hardness.

Monel 400 Bolt is a nickel-copper alloy, a solid solution nickel alloy that can only be hardened by cold work. Known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher than copper alloys in oxidizing environments. Monel 400 bolts, also known as Alloy 400, are also used in high temperature, caustic and salt solution applications.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Monel 400 products on a project basis is one of our strongest capabilities and is unmatched in our industry.

Monel 400 Bolts and Nuts are made from a nickel-copper alloy for extreme corrosion resistance, especially in sour conditions. The material is also strong and rigid and can be used to produce bolts and nuts for high temperature service. HT PIPE is a leading manufacturer and supplier of Monel 400 Bolts and Nuts of all sizes and types. Among the ingredients are carbon, aluminum, manganese, silicon, iron, sulfur and 63% nickel and 28% copper. This composition gives the material a high melting point.

In addition to high ductility, the material shares several other characteristics with nickel. For example, ASTM B164 Monel 400 round bar is well suited to work in moderately reducing applications because nickel works very well in reducing environments.

Monel 400 also resistant to corrosion of neutral solution, water, sea water, atmosphere and organic compounds.

Monelk500, also known as UNS N05500, has the same corrosion resistance as monel400, but has higher mechanical strength and hardness. It has good corrosion resistance and long-term organizational stability.

Monel gaskets, such as Monel 400 and K500, are made of nickel-copper alloys that exhibit high strength, toughness and good corrosion resistance over a wide temperature range. A standout feature of Monel gaskets is their excellent resistance to hydrofluoric acid, a particularly difficult acid to handle, at all concentrations up to the boiling point. For hydrofluoric acid applications, Monel gaskets are probably the most corrosion resistant of all commonly used specialty alloys.

Monel nickel copper k500 hex bolts are often used for standard and advanced applications where a combination of strength and corrosion resistance is a necessity. Monel UNS N05500¡¯s advanced quality corrosion resistance and usability in extreme conditions makes it the perfect choice for a wide range of industrial applications. Some of which, include:

Chemical processing equipment
Marine applications
Petroleum tills & gasoline tanks
Heat exchangers
Valves & pumps
Propeller shafts
Process vessels
And more

It has excellent solderability and can withstand very high pressure and weight. The alloy has excellent mechanical properties at sub-zero temperatures, with a melting point of 2370¡ã – 2460¡ã F, and the product can be used at temperatures up to 1000¡ã C.

The seamless pipes can easily slip onto the flange and reach the precise connection location. The ASTM B564 Monel 400 Lap Joint Flanges and other flanges can also come as threaded, forged, screwed or plate flange types. We could do solution treatment and ageing treatment for Monel K-500 forging flanges as per the clients. Monel is based on nickel (65-70%) and copper (20-29%) and also contains iron and manganese (5%) and other compounds.

Monel 400 Butt Weld Reducers are resistant to aggressive solvents, acids and bases, and seawater, are highly robust at high temperatures, and are also operable for use in many marine engineering applications.

Monel 400 is resistant to a variety of corrosive conditions. For example, acidic applications involving hydrofluoric acid, brine, sulfuric acid and bases. Alloy 400 can only be hardened by cold work. Monel 400 is used in many industries for its excellent corrosion resistance, especially marine and chemical processing.