ASTM B564 UNS N04400 Pipe Flange

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

In fact, in comparison to nickel, the corrosion resistance properties of UNS N04400 Orifice Flange tend to be much higher than nickel itself.

Monel K500 pipe bend and elbow are virtually nonmagnetic, even at quite low temperatures

These Monel 400 pipes have high strength and toughness over a wide temperature range and have excellent resistance to many corrosive environments.

Typical applications for alloy K-500 pipe bend and elbow are pump shafts and impellers; doctor blades and scrapers; oil-well drill collars and instruments; electronic components; springs; and valve trim.

Nickel 400 Annealed Pipe, which is also referred to as a superalloy can be annealed at a temperature of 926¡ãC.

It has high strength and excellent corrosion resistance in various acidic and alkaline environments, especially suitable for reducing conditions. It also has good ductility and thermal conductivity.

Monel K500 has about three times the yield strength and twice the tensile strength of Monel 400, and higher mechanical properties can be obtained by cold working or age hardening. Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.

Alloy 400 is low in strength in the annealed condition so, a variety of tempers may be used to increase the strength.

Monel 400 Flanges are made up of a nickel copper super alloy that is corrosion resistant and strong. The material could be welded easily and formed well.

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with good mechanical properties from sub-zero temperatures up to about 550 ¡ãC (1020 ¡ãF) and is approved for pressure vessels with wall temperatures from -10 to 425 ¡ãC (14 to 800 ¡ãF) according to VdTUV-Wbl. 263 and up to 900 ¡ãF (480 ¡ãC) according to ASME Boiler and Pressure Vessel Code.

Common trade names include alloy 400, UNS N04400, Monel alloy. Monel? is a registered tradename of Special Metals Corporation.

These products are manufactured with the latest technologies using high grade raw materials. We are manufacturer in national & international standards.

The high-temperature plasticity of the experimental alloy added with trace amounts of Mg, Cr and Co is obviously improved, and it exhibits certain superplasticity. At 1010¡æ, the strain rate sensitivity index m is 0.32, and the maximum elongation is 240%.

Monel400 is a single-phase solid solution Ni-Cu corrosion-resistant alloy.

A standout feature of Monel flanges is their excellent resistance to hydrofluoric acid, a particularly difficult acid to handle, at all concentrations up to the boiling point.

Alloy 400/Monel 400 comes directly from refined ore bodies in Canada, and with a copper content of approximately 30 wt%, it provides a lower cost alternative to commercially pure nickel, but still retains a very similar characteristics.

Essentially, Monel 500 is an age-hardened version of Monel 400. This means that Monel 500 is harder and more resistant to corrosion than Monel 400. This material can be used in sour gas applications. Monel K500 Studs maintain corrosion resistance even in high velocity seawater. Hence, these applications are in seawater and marine engineering applications as well as in shipbuilding applications.

MONEL Alloy K-500 (UNS N05500 / W.Nr. 2.4375) is a nickel-copper alloy that combines the excellent corrosion resistance of MONEL Alloy 400 with the added benefits of higher strength and hardness.

Monel K500 fasteners are cold worked prior to precipitation hardening. The strength of the fasteners is stable to 1200 degrees Fahrenheit. Here, at this temperature, it becomes more ductile, reaching toughness around 400 degrees Fahrenheit. Higher strength and hardness after precipitation hardening compared to 400. Due to its numerous advantages, Monel K500 ASTM fasteners are used in a wide range of industries.

The high pressure rating of Monel flanges means they can be used in high pressure environments.

ASME SB564 Monel UNS N04400 Weld Neck Flanges are utilised in pharmaceutical equipment, heat exchangers, condensers, power generation, etc. ANSI B 16.47 Monel DIN 2.4375 Threaded Flanges are welded to a pipe or fitting with a single full penetration. HT PIPE takes ultimate pride in offering the above mentioned range of products that fall under the Monel Flanges product type that come in two grades, 400 and K500. Also We offer wide range of Monel ASTM B564 400 Flanges such as Monel 400 Slip On Flanges, Monel K500 Weld Neck Flanges.

Monel 400 Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

The combination of very low corrosion rates in high-velocity sea water and high strength make alloy K-500 pipe bend and elbow particularly suitable for shafts of centrifugal pumps in marine service.

The levels of molybdenum and copper enable Monel K500 Ring Joint Type Flanges to resist reducing agents and acids. Our wide array of UNS N05500 | Monel K500 Threaded Flanges is utilize in rough oil stills, gas and new water tanks, marine installations and clasp, and concoction preparing gear.

The Alloy 400 Orifice Flange is a special type that is used to fit pipes together with an orifice. The minimum yield strength of the material is at 195MPa and the minimum tensile strength is 480MPa.

We are a maker, broker, stockist, provider and exporter of ASME SB564 Monel K500 Flanges which are precipitation solidified, high in quality ribs, yielding a rigidity of 115 ksi for a power pressed execution. Monel K500 fasteners and flanges offer a unique combination of high strength with similar corrosion resistance to Monel 400 and improved resistance to a sour-gas environments.

Typical applications are valves and pumps; pump and propeller shafts; marine fixtures and fasteners.

Alloy K500 is refined by Electroslag Refining (ESR), ensuring the cleanest and highest quality material. This increased alloy purity limits the potential for hard non-metallic inclusions that can increase machining difficulty, machining time and ultimately lead to part failure. It also has low permeability and is non-magnetic at temperatures as low as -150¡ãF (-101¡ãC).

ASTM B564 UNS N04400 Slip on Flange A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

Monel k500 round bar is an age hardening nickel base alloy. This nickel-based Monel UNS No5500 triangular bar also contains some elemental copper added to its alloy. Copper is known to have good corrosion resistance when added to Monel UNS 5500 spring steel bar, similar to alloy grade 400.