ASTM B564 UNS N04400 Pipe Flange

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

We are Manufacturers, Supplier and Exporters of Monel K500 Flanges. These Monel R405 flanges are used with stub end or daft which is butt welded to the pipe with the flange loose behind it.

Alloy 400 is a solid solution of gold that can only be hardened by cold work.

There are different standards to cover the different nominal bore sizes of the flanges. The ANSI B16.5 Monel DIN 2.4360 Blind Flange that has diameters ranging from ? inches to 48 inches in this standard.

These Monel 400 pipes have high strength and toughness over a wide temperature range and have excellent resistance to many corrosive environments.

Alloys like Monel 400 flanges perform well in marine environments due to their chemical composition. The copper content is between 28% and 34% and is known as a superalloy due to its good corrosion resistance.

Monel 400 flanges are also available for higher temperatures in reduction environments. While Monel 400 flanges are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 flanges.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Typical applications for alloy K-500 pipe bend and elbow are pump shafts and impellers; doctor blades and scrapers; oil-well drill collars and instruments; electronic components; springs; and valve trim.

Generally, the corrosion resistance of Monel K500 in solid solution is basically the same as that of Monel 400 alloy, so the corrosion resistance data of Monel 400 can be applied to Monel K500 alloy. Due to its low corrosion rate and high strength in flowing seawater, the alloy is particularly suitable for manufacturing seawater corrosion-resistant centrifugal pump shafts.

Monel 400 is widely used in Feed water and steam generator tubing.

The corrosion resistance of Monel K-500 is basically the same as Alloy 400, except that in the age hardened condition, Alloy K-500 has a greater tendency to stress corrosion cracking in certain environments. Monel K-500 has been found to be resistant to sour gas environments.

Monel 400 is a copper-nickel corrosion resistant alloy, which is a kind of corrosion resistant alloy with the largest usage, the most extensive use and excellent comprehensive performance.

Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.

Alloy 400 is a solid solution alloy that can only be hardened by cold working.

ASTM B564 UNS N04400 Pipe Flang Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

Alloy K500 is refined by Electro Slag Refining (ESR), ensuring the cleanest and highest quality of material is supplied.

Although ASTM B165 UNS N04400 material has lower strength in the annealed condition, it exhibits excellent mechanical properties even at sub-zero temperatures. Monel tubes can be used up to 1000 degrees Fahrenheit. In order to improve the mechanical properties of Monel 400 welded pipe, it is possible to make finished products on it.

Alloy K500 has approximately three (3) times the yield strength and double the tensile strength when compared with 400. MONEL K500 can be further strengthened by cold working before the precipitation hardening.

Monel 400 is also often used for the high tolerance tubing. It exhibits excellent weldability, and it is often found in marine applications such as seawater valves and pump shafts. These tubes are also used in chemical plant equipment, boiler feeders, and heat exchangers. For applications that require a high melting point and toughness under the harshest conditions.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

Alloy 400 pipe bend and elbow have excellent corrosion resistance together with increased strength and hardness.

Spring washers are locking washers that are used when there is a need to prevent a fastener from loosening as a result of vibration. They are also often called split lock or split ring washers.

Valued for its high strength and corrosion-resistant properties, Monel 400 is available from Continental Steel in multiple forms for use in a variety of end uses.

Our UNS N05500 Flanges provides resistance to stress-corrosion cracking, crevice corrosion, and pitting. These are accessible to our valuable customers in a different range of diameters, wall thicknesses, and sizes at quite affordable rates.

Monel K500 nuts are a result of an age hardening process where aluminum and titanium are added to the nickel-copper base and then precipitated throughout the matrix.

A nut is a fastener that runs through its inner radius. Nuts are used in combination with bolts to hold a virtually unlimited number of parts, objects and accessories for many types of applications. When Monel 400 alloy is used as a material for making nuts, benefits can be seen in the short and long term. Monel Nickel Copper 400 Nuts provide strength and corrosion resistance in both acidic and alkaline environments. Monel NiCu 400 nuts are also known for their favorable dimensional accuracy and non-corrosion in salt water and hydrofluoric acid.

Monel K-500 combines the excellent corrosion resistance of Monel 400 with the added benefits of higher strength and hardness. Performance can be improved by adding aluminum and titanium to the nickel-copper matrix and by heating under controlled conditions to precipitate submicroscopic particles of Ni 3 (Ti, Al) throughout the matrix.

The strength of Monel400 Cu-Ni alloy is low in the annealed state, so it exhibits a higher degree of strength in the rolled state.

Alloy 400 (UNS N04400) is a nickel copper alloy with high strength (comparable to structural steel) and toughness. Alloy 400 also has excellent corrosion resistance in a range of media including seawater, hydrofluoric acid, sulphuric acid and alkalis.

When utilized at subzero temperatures, these fasteners actually increase their tensile and yield strengths, while ductility and toughness are virtually unchanged. In addition, the flange face differs as flat face, raised face and ring type joint face as well. The Monel Slip On Flange is most useful with seamless pipes. The seamless pipes can easily slip onto the flange and reach the precise connection location. The ASTM B564 Monel 400 Lap Joint Flanges and other flanges can also come as threaded, forged, screwed or plate flange types.

There are different pressure classes of these flanges ranging from Class 150 Monel UNS N04400 Flanges to class 2500, and PN6 to PN64.