ASTM SB 366 Alloy 400 Monel 400 UNS N04400 Tube bending with great mechanical properties at subzero temperatures

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with excellent corrosion resistance in a wide range of marine and chemical environments and has freedom from chloride induced stress-corrosion cracking.

ASTM B564 UNS N04400 Pipe Flang Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

Increased performance is obtained by adding aluminum and titanium to a nickel-copper matrix. Flanges are pipe fittings that connect pipes to each other and are used to connect pipe ends. In addition, Monel K-500 flanges can be perfectly matched with various Monel K-500 pipes to ensure the stability and firmness of the connection.

MONEL K500 is non-magnetic. MONEL K500 should be annealed when welded and the weldment then stress relieved before aging.

Monel gaskets, such as Monel 400 and K500, are made of nickel-copper alloys that exhibit high strength, toughness and good corrosion resistance over a wide temperature range. A standout feature of Monel gaskets is their excellent resistance to hydrofluoric acid, a particularly difficult acid to handle, at all concentrations up to the boiling point. For hydrofluoric acid applications, Monel gaskets are probably the most corrosion resistant of all commonly used specialty alloys.

Monel K500 Bolts, also known as Alloy K500, are composed of a nickel alloy that combines the excellent corrosion resistance of Monel 400 with increased strength and hardness. These additional properties of Monel K500 bolts are the result of an age hardening process in which aluminum and titanium are added to a nickel-copper matrix, which is then precipitated throughout. Compared to 400, this process increases the yield strength of K500 by a factor of approximately 3 (110ksi vs. 45ksi) and doubles the tensile strength (160ksi vs. 83ksi). Monel K500 bolts will maintain their strength down to 1200¡ãF and even maintain their ductility down to -400¡ãF.

Monel 400 Welded Pipe (NA13, N04400) offer hardness, strength and corrosion resistance with good fabrication capabilities. Monel 400 ERW Pipe can easily be welded by gas metal arc, gas-tungsten arc or shielded metal arc processes using appropriate filler metals.

Monel K500 Flat Washers feature aluminum and titanium elements for the excellent corrosion resistance of Alloy 400; improved strength, hardness, erosion resistance and oxidation fatigue resistance. We manufacture all types of Monel K500 machined washers in virtually all shapes and sizes.

Monel K500 nuts are a result of an age hardening process where aluminum and titanium are added to the nickel-copper base and then precipitated throughout the matrix.

It is suitable for temperatures up to 1000¡ãF (538¡ãC). Alloy 400 has excellent resistance to cavitation and erosion in fast-flowing brackish or seawater.

MonelK-500 alloy has a strong aging cracking tendency after large cold deformation. Cracks initiate on the surface and propagate towards the center. There are both transcrystalline and intercrystalline forms.

Unique among Monel alloys, ASTM B165 Monel Seamless and Welded Pipe is considered a Puritan alloy because it contains the same nickel and copper content as the natural nickel ore found in the Sudbury mine in Ontario, Canada.

Monel 400 es una de las pocas aleaciones que conserva la resistencia a temperaturas bajo cero, asi que utilicela en estas situaciones.

Monel K500 Flanges is further virtually nonmagnetic, even at quite low temperatures. This UNS N05500 Monel are available in various evaluations and sizes, shapes. We offer Monel K500 Blind Flanges that is a unique combination of high strength with similar corrosion resistance to Monel 400 and improved resistance to a sour-gas environments.

In fact, in comparison to nickel, the corrosion resistance properties of UNS N04400 Orifice Flange tend to be much higher than nickel itself.

Stronger than 400, alloy K500 washer even retains this strength in corrosive. conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas.

Monel K500 is a precipitation-hardenable nickel-copper alloy that combines the excellent corrosion resistance characteristic of Monel 400 with the added advantage of greater strength and hardness.

A threaded rod, also known as a stud, is a relatively long rod that is threaded on both ends; the thread may extend along the complete length of the rod. They are designed to be used in tension. Threaded rod in bar stock form is often called all-thread.

Monel K500 has about three times the yield strength and twice the tensile strength of Monel 400, and higher mechanical properties can be obtained by cold working or age hardening. Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.

Monel 400 bolts can also be used at higher temperatures. While Monel 400 bolts are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 bolts. Even when cooled to the temperature of liquid hydrogen, Monel 400 will not undergo the ductile to brittle transition that can lead to fracture. This is especially unique compared to most ferrous materials, which are generally stronger but very brittle at extreme low temperatures.

Monel 400 or also known as Nickel-Copper 400 is a solid solution alloy that is a high strength material that can be used over a wide temperature range. It also has excellent corrosion resistance and has applications in many areas in marine and chemical processing. It is used in applications such as valves, pumps, fresh water tanks and propeller shafts.

Monel K500 Fasteners are precipitation hardenable nickel and copper base alloy fasteners. These fasteners are developed for the excellent corrosion resistance adding with benefits of great hardness and strength.

Monel K500, UNS N05500 (QQ-N-286), is a precipitation-hardenable nickel-copper alloy that combines the corrosion resistance of Monel alloy 400 with greater strength (over 2x as strong) and hardness. It also has low permeability and is nonmagnetic to temperatures as low as -150¡ãF (-101¡ãC).

A nut is a threaded fastener that can be used with a bolt to secure a virtually unlimited number of parts, objects, and accessories for many types of applications. Monel 500 alloy provides short and long term benefits when used as a material for making nuts. Monel nickel copper k500 nuts provide strength and corrosion resistance in both acidic and alkaline environments. Monel nickel copper k500 nuts are also known for their favorable dimensional accuracy and non-corrosion in salt water and hydrofluoric acid.

Monel bolts, like Monel 400 and K500, are made from a nickel-copper alloy and exhibit high strength, toughness and good corrosion resistance over a wide temperature range.

Monel K500 is a nickel-copper alloy that combines the excellent corrosion resistance of Monel 400 (link) with the added benefits of higher strength and hardness. Performance can be improved by adding aluminum and titanium to the nickel-copper matrix and by heating under controlled conditions to precipitate submicroscopic particles of Ni3 (Ti, Al) throughout the matrix. This is commonly referred to as age hardening or aging.

Monel K500 Washers have the same basic iron and carbon composition, but steel also contains a healthy dose of chromium that gives its famous corrosion resistance.

Monel 400 is used in process vessels, heat exchanger piping, and gasoline and potable water storage tanks in the marine sector. The non-sparking properties of this alloy make it suitable for high-risk situations in the explosives industry, rockets and pulp and paper industries.

Monel K500 fasteners also have some excellent seawater resistance for marine applications. Monel fasteners also have some high-strength metals that have good toughness at high temperatures.

Alloy 400 is a solid solution of gold that can only be hardened by cold work.