ASTM SB366 WPC N04400 Nickel Alloy Reducing Tees

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Monel K500(alloy K500), UNS N05500 (QQ-N-286), is a precipitation-hardenable nickel-copper alloy that combines the corrosion resistance of Monel alloy 400 with greater strength (over 2x as strong) and hardness. It also has low permeability and is nonmagnetic to temperatures as low as -150¡ãF (-101¡ãC). This alloy shows the corrosion resistant characteristics of grades such as Alloy 400 but with enhanced strength and hardness after precipitation hardening. However, it can be further strengthened by cold working before the precipitation hardening.

ASTM B564 UNS N04400 Slip on Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Monel 400 has excellent corrosion resistance in hot concentrated alkaline solution.

The alloy is used in many fields, especially marine and chemical processing.

The Monel 400 alloy is also known as super alloy monel. This alloy is available in some standard shapes such as hexagon, round, tube, pipe, plate, strip, sheet and wire.

Monel k500 has good corrosion resistance and long-term organizational stability.

Stronger than 400, alloy K500 washer even retains this strength in corrosive. conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas.

The alloy can be machined at satisfactory speeds with machine tools commonly used in the industry. Generally, cold drawn or cold drawn stress relief materials are recommended for the best machinability and smoothest finish.

A high nickel alloy with the addition of substantial amounts of copper to give the alloy excellent resistance to sodium chloride solutions, including brine and seawater. Therefore, UNS N04400 Alloy 400 Forged Fittings and Socket Weld Elbows can be used as part of an offshore piping system that may require a change of direction.

Typical application for MONEL K500 which takes advantage of high strength and corrosion resistance are pump shafts, impellers, propeller shafts, valve components for ships and offshore drilling towers, bolting, oil well drill collars and instrumentation components for oil and gas production. It is particularly well suited for centrifugal pumps in the marine industry because of its high strength and low corrosion rates in high-velocity seawater.

The seamless pipes can easily slip onto the flange and reach the precise connection location. The ASTM B564 Monel 400 Lap Joint Flanges and other flanges can also come as threaded, forged, screwed or plate flange types. We could do solution treatment and ageing treatment for Monel K-500 forging flanges as per the clients. Monel is based on nickel (65-70%) and copper (20-29%) and also contains iron and manganese (5%) and other compounds.

Monel K500, UNS N05500 (QQ-N-286), is a precipitation hardenable nickel-copper alloy that combines the corrosion resistance of Monel Alloy 400 with higher strength (more than 2x stronger) and hardness.

When in the age-hardened condition, Monel K-500 has a greater tendency toward stress-corrosion cracking in some environments than Monel 400. Alloy K-500 has approximately three times the yield strength and double the tensile strength when compared with alloy 400.

Alloy 400/Monel 400 comes directly from refined ore bodies in Canada, and with a copper content of approximately 30 wt%, it provides a lower cost alternative to commercially pure nickel, but still retains a very similar characteristics.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Monel 400 is resistant to steam and sea water as well as highly corrosive solutions such as sulfuric, hydrochloric and hydrofluoric acids after degassing. It has excellent solderability and can withstand very high pressure and weight. The alloy has excellent mechanical properties at sub-zero temperatures, with a melting point of 2370¡ã – 2460¡ã F, and the product can be used at temperatures up to 1000¡ã C.

Alloys like Monel 400 flanges perform well in marine environments due to their chemical composition. The copper content is between 28% and 34% and is known as a superalloy due to its good corrosion resistance.

Nimonic 80 a (Alloy 80A) is one of the most popular superalloys specified for gas turbines. Nimonic 80A fasteners are often specified because of their ability to withstand very high temperatures. This makes Nimonic bolts and nuts ideal for use in aircraft parts and custom-designed gas turbine components, from turbine blade mounting to exhaust nozzles on jet engines, where Nimonic fasteners are exposed to very high levels of pressure and heat.

Alloy 400 is a solid solution alloy that can only be hardened by cold working.

MONEL 400 solid solution alloy can be hardened by cold work, but can be hot worked or cold worked, then annealed into complex structures and welded using an appropriate welding process.

We offer W.Nr 2.4360 Monel 400 Male & Female Flanges to the oilfield fabrication, offshore and to petrochemical industries; our flanges are age hardened and are resistant to caustic solutions, seawater, and to chloride solutions and nitric acids, under oxidising and reducing temperatures. HT PIPE takes ultimate pride in offering the above mentioned range of products that fall under the Monel Flanges product type that come in two grades, 400 and K500. Also We offer wide range of Monel ASTM B564 400 Flanges such as Monel 400 Slip On Flanges, Monel K500 Weld Neck Flanges, Monel K500 Socket Weld Flanges, 400 Monel Alloy Blind Flanges, Alloy K500 Orifice Flanges, Monel 400 Spectacle Blind Flanges, Alloy K500 Screwed / Threaded Flanges, Monel Alloy 400 Reducing Flanges, Alloy K500 Ring Type Joint Flanges (RTJ) etc.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Las aplicaciones tipicas de la alta resistencia y resistencia a la corrosion de MONEL K500 son ejes de bombas, impulsores, ejes de helices, componentes de valvulas para barcos y torres de perforacion en alta mar, pernos, collares de pozos de petroleo y componentes de instrumentacion para la produccion de petroleo y gas.

Although ASTM B165 UNS N04400 material has lower strength in the annealed condition, it exhibits excellent mechanical properties even at sub-zero temperatures. Monel tubes can be used up to 1000 degrees Fahrenheit. In order to improve the mechanical properties of Monel 400 welded pipe, it is possible to make finished products on it.

Preferred by many a Monel Flanges Manufacturer In India, this alloy exhibits high tensile strength making it a commercially viable option for marine engineering purposes. The Wnr 2.4360 Reducing Flange is resistant to chloride stress corrosion cracking, which is a common issue in marine environments.

This is a nickel-copper, solid-solution alloy that is hardenable only by cold working. It has high strength and toughness over a wide temperature range and is resistant to many corrosive environments.

Monel K500 fasteners are precipitation hardenable nickel and copper based alloy fasteners. These fasteners were developed for excellent corrosion resistance and have high hardness and strength. ALLOYK500 is a nickel-copper alloy that is age-hardened by the addition of aluminum and titanium alloys.

It is suitable for temperatures up to 1000¡ãF (538¡ãC). Alloy 400 has excellent resistance to cavitation and erosion in fast-flowing brackish or seawater.

It is not useful in oxidizing acids, such as nitric acid and nitrous.

We manufacture Monel K500 flanges from nickel and copper alloys. The material has excellent resistance to aggressive materials and solutions such as oxidizing salts, acids, nitrates and other oxidizing agents.