bright bar A182 F9 steel rod

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

ASTM A182 F22 Forging raw material used for the manufacturing process is well-tested and inspected by inspection agencies and quality experts.

At elevated temperatures, conventional steels, unlike ASTM A 335 P91 pipes, begin to lose their microstructural form, leading to failure. A burst or crack in the pipe is a visible fault. But since SA 335 P91 chrome-plated welded pipe is well suited to sustain itself at high temperatures, failure rates are extremely low.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

Alloy steel is a steel alloyed by adding a variety of elements with a total amount between 1.0% and 50% in order to improve its mechanical properties. Alloy steels are divided into two categories: low alloy steels and high alloy steels. The distinction between the two is debatable. Smith and Hashemi defined the difference as 4.0%, while Degarmo et al. defined the difference as 8.0%. Most commonly, the phrase “alloy steel” refers to low alloy steel.

ASTM A182 Gr F9 flanges are typically designed for applications with high temperature requirements. Alloys used to produce flanges according to this specification include wrought or rolled alloys and several stainless steel grades.

The low alloy steel pipe flanges also tend to provide better mechanical properties as opposed to many conventional, standard mild or carbon steels.

ASME SA 335 P11 pipe is a pipe made of chrome molybdenum alloy. It is used for high temperature service. It is corrosion resistant, strong and malleable.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.53

Shaped flanges made by die forging or precision (lost wax) casting, depending on the mechanical properties of the flange, die forged flanges have higher strength than cast flanges. Precision profiled flanges manufactured by forging or casting require a model (tool).

The weld neck flange comprises of a round fitting that extends beyond the rim of the circumference. These flanges, typically manufactured from forging, are actually welded to pipes.

A335 P9 seamless pipe is a type of chrome molybdenum pipe listed in ASTM A335 (ASME S/A335, Chrome-Moly), which has become the standard in the power generation industry and petrochemical industry, not only because of its tensile strength, corrosion resistance resistance and high temperature strength, but also because of its cost-effectiveness. Chromium molybdenum tubes are popular in P grades P5, P9, P11, P22, P91 and P92. The P11, P22 and P91 grades are most commonly used in the powder industry and petrochemical plants, while the P5 and P9 grades are often used in oil refineries.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.66

ASTM A193 Grade B8 Grade 1 Bolts and Studs Made of AISI 304 Stainless Steel. Type 304 is the most commonly used stainless steel grade in the fastener industry.

The specification for ASTM A320 Grade L7m materials covers alloy steel and stainless steel bolting materials for low temperature applications. ASTM A320 L7 Studs can also be used in applications with ambient temperatures up to -150oF. ASTM A320 grade L7m bolts and ASTM A320 bolts have a minimum Charpy impact value of 15 foot-pounds at this temperature.

The material contains carbon, manganese, phosphorus, sulfur, silicon, 8% chromium and molybdenum in a mixture. SA 335 grade P5 alloy steel pipe has similar strength to most austenitic stainless steel grades, with a minimum yield strength of 205MPa and a minimum tensile strength of 415MPa.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P120

Schedules vary based on nominal bore diameter in relation to wall thickness. Schedules range from sch20 to XXS. Pipe lengths up to 13500 mm. There are seamless pipes and fabricated pipes in this specification. ASTM A335 P5 pipe can be round, hydraulic, rectangular, square or hexagonal. The length of the pipe can also be cut to length size according to customer requirements.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P148

ASTM A193 Grade B7 bolts are made of chrome-molybdenum material with high tensile strength and good elongation properties.

A335 grade P5c pipe is a low alloy carbon steel (Cr-Mo) self-quenching in air where high hardness and residual stress are required for welding and it is not recommended for direct use in services requiring critical conditions. This situation requires the application of post weld heat treatment (PWHT). If you want to avoid PWHT then you can use preheat (120¡ãC) when soldering A335 grade P5c tubes. PWHT is required if the thickness of ASTM A335/ASME SA335 P5c alloy steel pipe is greater than 13 mm.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P149

A335/SA335 materials are used in a wide variety of plants and processes worldwide, including refineries, power plants, petrochemical plants, hydrocrackers, cokers, high temperature and ultra-high temperature lines, reheat lines, distillation, oil field service, and more.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P144

ASTM A193 Grade B7 is the standard material specification for chromium-molybdenum alloy steel fasteners for high-strength, high-temperature, and special-purpose applications. Grade B7 is a heat treated chromium molybdenum alloy steel with a minimum tensile requirement of 100 ksi, a yield strength of 75 ksi and a maximum hardness of 35 HRC. The ASTM A193 specification covers requirements for chemical composition, mechanical properties, hardness, heat treatment, and recommended nut washers for Class B7 fasteners. ASTM A193 Grade B7 is the broadest specification for fasteners, commonly found in bolts or pipes, pressure vessels, valves, flanges and fittings.

A182 F5 material is an excellent alloy that is hardened only by cold working. It is often used in nuclear energy, medical equipment, chemical energy, etc. These ASTM A182 Grade F5 Flanges gives extraordinary erosion resistance in, for instance, caustic and acidic applications which includes sulphuric and higher chloride environments.

C276 has good fabricability and impressive corrosion resistance in some of the most severe environments.

ASTM A193 Grade B7 is a standard material specification for chromium-molybdenum alloy steel fasteners for use in high tensile, high temperature and special purpose applications.

S32205 is a duplex stainless steel with twice the strength of austenitic stainless steel. Duplex stainless steel composed of 21% chromium, 2.5% molybdenum and 4.5% nickel-nitrogen alloy. It has high strength, good impact toughness and good overall and local stress corrosion resistance. The yield strength of duplex stainless steels is twice that of austenitic stainless steels, a feature that allows designers to reduce weight when designing products, making this alloy more affordable than 316, 317L. This alloy is particularly suitable for use in the -50¡ãF/+600¡ãF temperature range. For applications outside this temperature range, this alloy can also be considered, but there are some limitations, especially when applied to welded structures. Duplex stainless steel has twice the compressive strength compared to austenitic stainless steel, and designers can reduce its weight compared to 316L and 317L. Alloy 2205 is particularly suitable for use in the -50¡ãF/+600¡ãF temperature range, and can also be used at lower temperatures under severe restrictions (especially for welded structures).

ASTM A860 WPHY 60 Fittings are wrought carbon steel fittings that are either seamless or welded with high yield strength. The WPHY 60 indicates that the minimum yield strength of the ASTM A860 WPHY 60 Fittings is 60ksi.

ASME SA 335 P91 Alloy Steel Pipe also has some other great features like low maintenance, efficient work, high demands, etc. We offer a range of ASTM A335 P91 alloy steel pipes for a wide range of applications in various industries.

Alloy Steel AISI 4140 bar stock or forging stock to produce B7 headed and non-headed bolts. A193 Grade B7 is the most commonly used Bolt specification coupled with A194 Grade 2H Nuts for Bolting Carbon Steel pipeline. A193 B7 bolting is available in metric sizes from M6 to M180 and imperial sizes from 1/4 to 7 inches, in diameter.

Alloy steel sounds like: steel that contains a specific amount of alloying elements. Generally, alloying elements make steel stronger and more resistant to shock or stress. While the most common alloying elements include nickel, chromium, molybdenum, manganese, silicon and copper, many other alloying elements are also used in the production of steel.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.42

The A335 p12 material composition includes carbon up to 0.05 ¨C 0.15, manganese up to 0.30 ¨C 0.61, sulfur and phosphorus up to 0.025, silicon up to 0.5, chromium 0.80-1.25 and molybdenum up to 0.44-0.65. This steel shall meet the specified chemical composition, tensile properties and hardness requirements.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.66

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

The ASTM A/ASME SA 335 specification covers seamless ferritic alloy steel pipes for high temperature service. The pipe is mainly used for bending, vanstoning and similar forming operations, as well as for fusion welding.

Although the properties of the fitting depend on the alloy used to manufacture them. Another process that improves the mechanical properties of ASTM A182 F9 Alloy Steel Flanges is the forging process. These Grade F9 Weld Neck Flanges can also be reused and are meant for high pressure applications. This is the reason as per the specification they have to be rolled or forged.

ASTM A182 F11 Alloy Steel Flanges are used in manufacturing of flanges and fittings and are used in industries where cold temperature is observed and corrosion resistance doesn¡¯t matter much.