bs 4825 304l stainless steel pipe

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

316L 1.4401 S31603 Stainless Steel Pipe is a highly versatile and durable pipe option commonly used in a wide range of industrial and commercial applications. This SS UNS S31603 pipe is made from high quality 316L stainless steel with excellent resistance to corrosion, oxidation and staining, making it ideal for harsh environments or high stress applications.

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

ASME B36.19M is the standard specification for stainless steel pipes, which specifies the dimensions, tolerance, and manufacturing requirements for both welded and seamless pipes.

ASTM A312 TP316 is a standard specification for seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipes used in high-temperature and general corrosive service applications. The 316 Seamless Industrial Steel Pipe is made from a combination of chromium, nickel, and molybdenum, which gives SS 316 Seamless Tube excellent resistance to corrosion and rust.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

A tee has three openings, namely an inlet and two outlets; A chemical pipe fitting with two inlets and one outlet, either T-shaped or Y-shaped

ASTM A815 UNS S32205 Long Radius Elbow is used in turning pipe direction and is also resistant to chloride and sulfide environments. These ASME B16.9 Duplex Stainless Steel Seamless Fittings have a higher chromium content.

The 6mo Plate Flange displays outstanding resistance to crevice corrosion stress cracking, pitting, as well as corrosion fatigue uniform corrosion.

The flange connection type usually comes with a double unit, with washers and some bolts and nuts to connect to each other. (The pipe is welded on the flange first, and then the valve and other equipment are installed on the flange.) When connecting these parts, put the gasket between the two flanges, and then tighten the flange screws so that the two are tightly connected together. Flange connection is convenient, flexible and labor-saving. When the pipeline is repaired, the screws on the flange can be removed, and the corresponding pipeline or valve can be removed. Also replace with new pipes and valves.

Hastelloy C22 weld neck flanges have the best resistance to pitting and stress corrosion cracking.

ASTM A815 UNS S32760 fittings is the one where the strength is excellent and the corrosion resistance is excellent.The material for fittings shall consist of forgings, bars, plates, or seamless or welded tubular products.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

Stainless steel WNR 1.4550 washers have serrations that extend radially inward or outward to bite into the bearing surface. If a flat washer is required to span a large hole in the assembly, a nyloc nut (nylon insert) must be used. 347 stainless steel washers are austenitic stainless steel washers made from an alloy containing chromium, nickel, molybdenum and nitrogen with limited carbon content. Stainless steel 347 gaskets are used in corrosive environments.

The austenitic structure of 316L also gives these grades excellent toughness, even at low temperatures.

Stainless steel is an alloy of iron that is resistant to rusting. It contains at least 11% chromium and may contain elements such as carbon, other nonmetals and metals to obtain other desired properties. Stainless steel’s resistance to corrosion results from the chromium, which forms a passive film that can protect the material and self-heal in the presence of oxygen.
A stainless steel pipe system is the product of choice for carrying corrosive or sanitary fluids, slurries and gases, particularly where high pressures, high temperatures or corrosive environments are involved. As a result of the aesthetic properties of stainless steel, pipe is often use in architectural applications.

The pipes to the buyers are supplied at market leading rates.

Inconel 718 alloy is a precipitation hardenable nickel-based alloy. It has good ductility in the annealed condition and very high yield, tensile and creep rupture properties at temperatures up to 1300 degrees Fahrenheit.

Medium carbon steel bolts, anchor bolts, screws, studs, nuts and self-drilling screws contain between 0.25 – 0.60% carbon and 0.60 – 1.65% manganese by weight. The mechanical properties of these studs are improved by heat treatment.

The 800H modification was to control carbon (0.05 to 0.10%) and grain size to (>ASTM 5) to optimize stress rupture properties.

The low alloy steel pipe flanges also tend to provide better mechanical properties as opposed to many conventional, standard mild or carbon steels.

Alloy 400 is a solid solution of gold that can only be hardened by cold work.

We manufacture 309 Stainless Steel Carriage Bolts under strict supervision of our professional team which guarantees the highest quality.

Hastelloy C276 material is designed with good mechanical properties. They have a minimum tensile strength of 601Mpa and a minimum yield strength of 204Mpa. This material makes the alloy easy to machine and elongate.

The Inconel 600 Seamless Pipes have many features like good workability, durability, readily weldable, high strength and mechanical property as well. There are various types of Inconel 600 pipes are available such as welded, seamless, square, rectangular, thick wall, thin wall, electro polished, etc.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

Stainless steel flange not only saves space and weight, but also ensures that the joint will not leak and has good sealing performance. The compact flange size is reduced because the diameter of the seal is reduced, which will reduce the section of the sealing surface.

The addition of titanium stabilizes Alloy 825 against sensitization in the as-welded condition making the alloy resistant to intergranular attack after exposure to temperatures in a range that would sensitize un-stabilized stainless steels.

Additionally, the higher content of chromium used to alloy the stainless steel 304 seamless pipes are what provides resistance against oxidizing solutions up to a temperature of about 176¡ãF such as nitric acid, up to 55% weight.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

A335 has improved wear resistance at higher temperatures. It has good formability and machinability without deformation and deformation. It has good thermal stability in pressurized environments.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.35

Stainless steel is on average 2.5 times stronger than copper and performs far much better on the strain and stress tests. The relatively weaker structure for copper makes its piping vulnerable to external forces that may cause cracks and leaks.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Monel 400 bolts can also be used at higher temperatures. While Monel 400 bolts are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 bolts. Even when cooled to the temperature of liquid hydrogen, Monel 400 will not undergo the ductile to brittle transition that can lead to fracture. This is especially unique compared to most ferrous materials, which are generally stronger but very brittle at extreme low temperatures.

Industry users like the resistance to a wide range of organic acids and the resistance to chloride-induced stress-corrosion cracking.

Alloy 2205 UNS S32305/S31803 is a 22% chromium, 3% molybdenum, 5-6% nickel, nitrogen alloyed Duplex Stainless Steel Pipe with high general, localized, and stress corrosion resistance properties in addition to high strength and excellent impact toughness.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The corrosion resistance comes from the addition of alloying material, mostly the chromium content. The ASTM A790 Pipes are resistant to pitting corrosion and crevice corrosion. The pipes could also be electric fusion welded.

SB564 UNS N02200 Flange The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.