carbon steel 8.8 flat U-Bolt ASTM F436 price

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

Inconel 718 is a nickel-chromium-based alloy that is commonly used in high-temperature applications such as aerospace and gas turbines. One of the most important factors in the production of ASTM B670 Inconel 718 Sheet is the plate rolling process. There are two main types of Inconel 718 plates available on the market: hot rolled and cold rolled plates.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

Nickel 200 flanges The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

ASTM A312 TP316 is a standard specification for seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipes used in high-temperature and general corrosive service applications. The 316 Seamless Industrial Steel Pipe is made from a combination of chromium, nickel, and molybdenum, which gives SS 316 Seamless Tube excellent resistance to corrosion and rust.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

304 Piping Spools are made of 304 Stainless Steel, a common and popular material in many industrial applications that require resistance to corrosion and oxidation. These S30400 Piping Spools are prefabricated using specialized machinery and processes, which ensure that they are highly accurate and reliable.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

316L 1.4401 S31603 Stainless Steel Pipe is a highly versatile and durable pipe option commonly used in a wide range of industrial and commercial applications. This SS UNS S31603 pipe is made from high quality 316L stainless steel with excellent resistance to corrosion, oxidation and staining, making it ideal for harsh environments or high stress applications.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

ASME B36.19M is the standard specification for stainless steel pipes, which specifies the dimensions, tolerance, and manufacturing requirements for both welded and seamless pipes.

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Similar to other Inconel alloy grades, the base element of alloy Inconel 625 spring steel bars is nickel. UNS N06625 / W.Nr. 2.4856, also known as Nickel Alloy 625 Hot rolled bar is an alloy of nickel and chromium with the addition of molybdenum and niobium.

904L is the austenitic stainless steel material. The addition of molybdenum is providing it excellent resistance to the localized attacks such as crevice corrosion and pitting by chlorides.

AS1210 Prequalified Incoloy 800 can be used at 800¡ãC. ASME codes allow Incoloy 800 to 815¡ãC, and Incoloy 800H and 800HT to 982¡ãC.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Alloy 904L is a non-stabilized, high alloy austenitic stainless steel with low carbon content.

NAS NW276 is a Ni Cr Mo alloy with excellent corrosion resistance in both oxidizing and reducing atmospheres. In this alloy, carbide precipitation in the heat affected zone (HAZ) is suppressed and corrosion resistance is improved by reducing the contents of C and Si.

The alloy must be cooled for heat treatment prior to AISI AS F11 Hex Bar. All parameters of the heat treatment procedure are set by the specification, including the type of heat treatment, austenitization/solution temperature, and alloy steel F11 A182 bars.

ASTM A694 carbon steel is the most common grade of carbon steel used for round bar development. The increased carbon content of the alloy reduces ductility by increasing tensile strength.

Nickel 718 plate has higher strength than Inconel X-750 and better mechanical properties at lower temperatures than Nimonic 90 and Alloy X-750. Nickel 718 coils offer excellent solderability compared to aluminum and titanium hardened nickel-based superalloys.

F11 alloy steel pipe flange is the second most common connection method after welding. Use them when joints need to be disassembled. ASTM A182 Gr F11 flanges provide flexibility for maintenance. It connects pipes with various equipment and valves.

253 MA is a depleted austenitic heat-resistant alloy with high strength and excellent oxidation resistance. It provides excellent creep strength and resistance to oxidation, sulfidation and erosion at elevated temperatures in an alloy containing only 11% nickel. Stainless steel 235MA fasteners can be manufactured in a variety of sizes, sizes and grades to customer requirements. Since there are various types of machines, there are also different grades of fasteners.

All our stainless steel bolts and nuts have no minimum order quantities, you can order as little as one bolt or nut. If you still can’t find what you are looking for, please contact us.

ASTM A516 CS 70 grade flanges are used in a variety of applications such as bridges, buildings, auto and truck parts, rail vehicles, pressure vessels, boilers, valves, heat exchangers, cargo containers, suitcases, construction equipment, structural pipes and Power poles, etc.

S32760 has very good resistance to localized corrosion and stress corrosion cracking and high mechanical strength.

Knowing the finish of these steels can be helpful if your pipes are visible and appearance is on the list of considerations. Stainless steel is usually glossy and can retain that gloss if exposed to weather and other factors. Carbon steel, on the other hand, is darker in color and usually has a matte finish when painted. Unfortunately, it can also rust and look bad if left exposed. Galvanizing is also an option.

A flange is a ring of steel (forged, cut from plate, or rolled) designed to connect sections of pipe, or to join pipe to a pressure vessel, valve, pump or other integral flanged assembly. Flanges are joined to each other by bolts, and to the piping system by welding or threading (or loose when stub ends are used). Stainless steel flange simplified as SS flange, it refers to the flanges that made of stainless steel. Common material standards and Grades are ASTM A182 Grade F304/L and F316/L, with pressure ratings from Class 150, 300, 600 etc and to 2500. It used in more industries than carbon steel as stainless steel has better resistant performances on corrosion environment and always provides with a good appearance.

926 is an austenitic stainless steel alloy with a chemical composition similar to alloy 904L with 0.2% nitrogen and 6.5% molybdenum. Molybdenum and nitrogen contents significantly improve pitting and crevice corrosion resistance in halide media. At the same time, nickel and nitrogen not only ensure the stability of the metallographic phase, but also reduce the tendency of intergranular segregation during thermal process or welding process better than nitrogen content. Nickel alloy. 926 has exceptional corrosion resistance in chloride ion media due to its excellent localized corrosion resistance and 25% nickel alloy content.

ASTM A335 P11 is part of ASTM A335, Pipe shall be suitable for bending, flanging, and similar forming operations, as well as fusion welding. The steel shall meet the requirements of chemical composition, tensile properties and hardness. Each pipe shall be hydrostatically tested. In addition, each pipe shall be inspected in accordance with the practice required for non-destructive testing.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.45

Grade 316 is the standard austenitic grade that has molybdenum. The molybdenum gives 316 batter overall corrosion resistance properties than 304 grade particularly higher resistance to pitting (defect like indention) and crevice corrosion. 316 grades also give excellent toughness even through cryogenic temperatures.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The alloy has been used in a variety of applications. It has excellent resistance to rapidly flowing brackish water or seawater. It is particularly resistant to hydrochloric and hydrofluoric acids when they are de-aerated.

The most common reason for Inconel is because it is an alloy that, despite exposure to high temperatures, provides excellent performance when common alloys fail.

These SS 347 flat washers offer high strength, good corrosion resistance, good mechanical properties up to 600¡ãF (316¡ãC), and good toughness in the base metal and weld. Our stainless steel 347 lock washers are widely used in the aerospace, chemical, petrochemical, food processing, paper and general metalworking industries. At the same time, Din 1.4550 washers are slightly tougher than SS 304 and will produce equally tough sticky chips. Stainless Steel 347 Punch Washers have excellent resistance to intergranular corrosion when exposed to temperatures in the 800 ¨C 1500¡ãF (427 ¨C 816¡ãC) range for chromium carbide precipitation.

A weld neck flange, also called a tapered hub flange or high-hub flange, is a kind of flange that can relocate stress to the pipes, ensuring a decrease in high-stress concentration at the bottom of the flange.

Our Alloy Steel Seamless Pipes (IBR) are made of alloy steel with excellent properties. These were developed for energy-related applications involving oil and gas drilling and are therefore subject to the stress of machine parts. In addition, alloy steel pipes are used in domestic, professional or industrial fields.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P116

All in all, if you need superior corrosion resistance and your application contains water, then 316 steel is worth it. If not, 304 steel will suit your needs well.

The solution annealing treatment is required prior age hardening / precipitation hardening. The single phase microstructure created during solution annealing is required prior to age hardening, such that only the precipitates formed during age hardening will be present in the final product. The composition, size, and quantities of those precipitates formed during aging will determine the final product’s hardness, strength, and mechanical properties after aging. It is critical that the structure be properly solution treated prior to aging in order to meet all of these requirements.

At moderate temperatures, Werkstoff No 1.4301 SS 304 Flanges can also deliver a good performance in caustic solutions, especially those solutions that are free of chlorides or fluorides.

Duplex Steel S32205 Slip On Flange is placed over the pipe which extends from the end of the pipe and based on the inside diameter. The outer diameter is also welded on the back side of the flange.

Inconel 718 contains nickel, chromium and molybdenum alloys as well as aluminum, niobium and titanium elements and is suitable for flange manufacturing. Our premium flanges have excellent yield strength and tensile strength. Our premium flanges also offer excellent resistance to corrosion, crevice corrosion, pitting and oxidation in severely corrosive environments. Has excellent workability, weldability and machinability,

Titanium NCF Tube is a silvered colored metal with high strength and low density.