DIN931 ASTM A193 B7 partial thread Nature alloy steel din931-8.8 bolts alloy steel hex bolt

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

It is a standard specification defining typical chemical composition, mechanical properties, hardness requirement, preferential heat treatment, product marking, certification and other requirements, suitable for bolting used in pressure vessel service, valves, flanges and fittings. ASTM A193 defines both SI (Metric) and inch-pound units.

A182 F2 round bar has high strength, formability and hardenability.

B7 threaded studs and short head bolts are readily available in the market. B7 grade bolts are often used for pipe flange connections. These bolts are usually sold in a normal bare metal finish, but are usually hot-dip galvanized, galvanized, Xylan coated, PTFE coated, or otherwise treated with a corrosion resistant coating.

The size of these forgings range from ? NB to 250 NB and length of these forgings is 2mm to 40mm.

ASTM A182 Alloy Steel Forged Fittings are manufactured according to the ASTM A182 specification, which covers high pressure and high temperature service flanges covered by ASME B16.11, MSS-SP-79/ 83/ 95/ 97 and BS3799 standards.

The Chromium content in the alloy aids in improving its anti-oxidization and anti-corrosion properties. This steel is usually supplied by the alloy steel flanges manufacturers in India in an annealed or normalized and tempered condition.

The heat treatment could be heat treated according to any of the WPHY 52 specification by either tempering, normalizing, quenching or stress relieving.A860 refers to the high quality of the fittings.

We can supply chrome molybdenum alloy flanges sorted by alloy grade, size and pressure.

ASTM A182 is the Standard Specification for Forged or Rolled Alloy Steel Pipe ASTM A182 F11 Flanges, Forged Fittings, and Valves and Parts. These alloy steel A182 grade F11 WNRF flanges are designed for high temperature applications.

ASTM A320 L7M Grade AS Fasteners are commonly used in oil and gas exploration and processing equipment – piping, piping and heat exchangers.

Alloy Steel Threaded Flanges are widely demanded as pipe flanges i.e called as threaded flanges which is useful in different industrial applications. It is also known as screwed flange and it has a thread inside the flange bore which fits on the pipe with matching male thread on the pipe.

These industries are rely on MSS SP75 WPHY 52 Welded Pipe Fittings and MSS SP75 WPHY Grade 52 Seamless Pipe Fitting because these fittings can withstand severe corrosion problems in harsh conditions.ASTM A860 WPHY 52 are Created High Yield fittings and are by and large utilized at High-pressure prerequisites.

Alloy Steel AISI 4140 bar stock or forging stock to produce B7 headed and non-headed bolts. A193 Grade B7 is the most commonly used Bolt specification coupled with A194 Grade 2H Nuts for Bolting Carbon Steel pipeline. A193 B7 bolting is available in metric sizes from M6 to M180 and imperial sizes from 1/4 to 7 inches, in diameter.

L7 threaded studs and short head bolts are readily available in the market.

The alloy steel of ASTM A182 F11 flanges is called chrome-moly flanges. These are flanges that contain chromium and molybdenum, these are the ingredients that make them resistant to corrosion, which also adds to its toughness.

Chrome molybdenum grades P11, P22, P91 and P92 are used in the power industry. Chromium molybdenum grades P5 and P9 are used in petrochemical refining processes. Chrome molybdenum forged fittings and flanges are available in grades F5, F9, F11, F22, F91, F92. Chrome-molybdenum alloy butt welded pipe fittings are available in WP5, WP9, WP11, WP22, WP91, WP92 grades. F11 and F22 materials comply with NACE-MRO 175.

A335 P5, P9, P11, P12, P22, P91 grade alloy steel seamless pipes are individually sheathed in plastic bags, and the pieces are made of waterproof packaging material and tied with nylon ropes. There is a clear label on the outside of the package for easy identification of quantity and product ID with great care during handling and shipping.

Grade B7 is a heat-treated chromium-molybdenum alloy steel with minimum tensile requirement of 100 ksi, yield of 75 ksi and maximum hardness of 35 HRC.

The plates are annealed in different condition which offers them strength. Since these plates are to be worked at high temperatures and pressure environment therefore the elements included in it matters a lot. What elements are added in the manufacturing add different properties for example, high level of chromium adds excellent corrosion resistance. It also offers excellent oxidation resistance. Resistant to oxygen is important in petrochemical and gas industries and therefore these plates are used.

These flanges are available in different types such as slip flanges, blind flanges, butt weld flanges, socket weld flanges, orifice flanges, eyeglass blind flanges, threaded/threaded flanges, reducer flanges, ring flanges Type joint flange (RTJ), etc.

When moving high-temperature or corrosive media through Chrome Alloy Pipe from one process to the next, flanges capable of withstanding harsh environments are critical

N04400 is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Alloy N04400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acid-like substances), brine, hydrofluoric acid, and sulfuric acid. Other advantages of using this alloy are toughness and high strength over a wide temperature range; it can also be manipulated to be magnetic if desired.

Low alloy steel ASTM A182 F11 flanges typically have a total alloy content of 1.5% – 5%. Its common alloying elements are manganese, chromium, silicon, nickel, molybdenum and vanadium. It may contain up to four or five different quantities of these alloys. At the same time, the increased strength of the alloy steel F11 flange may require higher forming pressures. Annealing of SA 182 Gr F11 steel flanges is accomplished by water quenching by thorough immersion at 1725¡ãF – 1850¡ãF (941¡ãC – 1010¡ãC) and can only be hardened by cold work.

Alloy 20 (Alloy 20) is an iron-based austenitic alloy developed to resist sulfuric acid corrosion. It has excellent resistance to sulfuric acid corrosion; it has strong resistance to phosphoric acid, nitric acid and chloride environments, chloride stress corrosion, pitting corrosion and crack corrosion. Therefore, alloy 20 has the name of anti-corrosion alloy; it has a wide range of applications: such as: chemical, food, medicine, power production and plastics industries will use it. For resistance to pitting corrosion and chloride corrosion, stress corrosion cracking problems, etc., alloy 20 is often used.

Chromium and molybdenum are high in A335 pipes. While molybdenum improves overall strength, resistance, elasticity, hardenability and overall quality, molybdenum ensures that the material is more resistant to softening, inhibits grain growth and reduces the chance of embrittlement. It is the only additive that improves the high temperature resistance and also improves the corrosion resistance of the steel.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P105

Alloy steel F12 bar offers some great properties such as strong construction, all-around durability, a wide range of sizes to choose from, and more.

The material can be heat treated to anneal and normalize in air, or quench and temper in polymer or oil. Alloy 4130 has a lower carbon content of 0.28% – 0.33% and slightly higher amounts of other elements. And the material is easy to process. 4140 low alloy steel has a range of 2. 375″ to 12.750″ OD with wall thicknesses ranging from 0.375″ to 1.5″. Alloy 4145 has a slightly higher carbon content than 4140 and 4130 types of pipes.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P139

Alloy steel f9 flanges are thinner in size compared to other flanges. Therefore, astm a182 f9 blind flanges tend to be ideal for tight work spaces.

ASTM A182 F9 Flanges also have higher corrosion resistance levels. Alloy Steel F9 Threaded Flanges can be susceptible to sensitisation, the formation of grain boundary chromium carbides at temperatures between approximately 900 and 1500 Degree F (425 to 815 Degree C) which can result in intergranular corrosion.

Please make sure to contact us for more information on the pipe fitting products such as the ASTM A860 MSS SP 75 WPHY 52 Pipe Fittings and their pricing.