DIN933 ASTM A193 B7 full thread Nature alloy steel2.5 mm hex bolts ss316 hex bolt hex bolt

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

ASTM A182 Alloy Steel Forged Flanges are manufactured according to the ASTM A182 specification, which covers high pressure and high temperature service flanges covered by ASME B16.5, B16.47 and B16.48 standards.

The ease and economy with which INCONEL alloy 718
can be fabricated, combined with good tensile, fatigue,
creep, and rupture strength, have resulted in its use in a
wide range of applications.

A182 alloy flange has good dimensional accuracy.

These ASTM A182 Alloy Steel pipe fittings are manufactured from high quality raw materials, so the manufactured products are of high quality. Additionally, these ASTM A182 Alloy Steel pipe fittings are manufactured with the necessary standards, codes and guidelines in mind, resulting in a high quality product.

The A320 Gr L7 stud material will undergo the following parametric tests – Impact Test, Tensile Test and Hardness Test according to the mechanical specification of A320 Grade L7 Bolts. The specification of A320 Gr L7 Hdg covers several grades of stainless steel including austenitic and ferritic stainless steels.

Our products are a symbol of constant innovation and superior quality.

The skills of chromium alloy steel include higher oxidation corrosion rates. In addition to being resistant to oxidation, alloy steel P91 of A335 steel pipe is also able to withstand very high temperatures and can be used in applications involving boilers, heaters, power generation, and more. The above applications work based on elevated temperature, which is why many suppliers recommend alloy steel P91 pipe for the above applications.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.21

These continuous ¨C annealing furnaces in Alloy Steel Grade F12 RTJ Flanges are usually heated by gas ¨C fired radiation tubes in order to separate combustion gases from the inert atmosphere surrounding the strip. Alloy Steel F12 Flanges has applications in many industries such as petrochemical, oil and gas, bulk liquid transportation, pharmaceuticals, chemical, pulp and paper manufacturing, power generation, textiles and others.

We offer alloy steel grade 2H washers in various specifications and ranges according to the precise needs and selection of our customers. Alloy Steel Grade 2H Star Washers can be produced in standard sizes or custom made to your specific requirements. Customers can take advantage of what we offer alloy steel grade 2H spring washers at market leading prices.

Alloy pipe is defined according to the material used in production (ie material), as the name suggests, it is made of alloy pipe; seamless pipe is defined according to the production process (seamless), which is different from seamless pipe is seamless pipe, Including straight seam welded pipe and spiral pipe.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.27

ASTM A320 L7 Stud Bolts are designed for low temperature performance. These fasteners are commonly used in valves, flanges, fittings and pressure vessels. The ASTM specification recommends a minimum impact value of 20-ft-lbf -150F for ASTM A320 L7 studs.

The manufacturing process of A860 WPHY 52 includes heat treatment.

The material has high creep resistance and corrosion resistance. The molybdenum content provides creep resistance and pitting resistance to the pipe. ASTM A335 P22 pipe is suitable for high temperature service. The ability to use at high temperatures comes from the ingredients. The composition of ASTM A335 P22 welded pipe contains carbon, manganese, phosphorus, sulfur, silicon, chromium and molybdenum.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.56

INCONEL? alloy 718 (UNS N07718/W.Nr. 2.4668) is a high-strength, corrosion-resistant nickel chromium material used at -423¡ã to 1300¡ãF. Inconel alloys are resistant to oxidation and have the ability to maintain its structural integrity in high temperature atmospheres.

Commercially pure wrought Nickel with good mechanical properties over a wide range of temperature and excellent resistance to many corrosives, in particular hydroxides.

Good resistance to corrosion in acids and alkalis and is most useful under reducing conditions. Outstanding resistance to caustic alkalis up to and including the molten state. In acid, alkaline and neutral salt solutions the material shows good resistance, but in oxidizing salt solutions severe attack will occur. Resistant to all dry gases at room temperature and in dry chlorine and hydrogen chloride may be used in temperatures up to 550C. Resistance to mineral acids varies according to temperature and concentration and whether the solution is aerated or not. Corrosion resistance is better in de aerated acid.

ASTM A193 Grade B7 specification covers the requirements for high strength alloy steel bolting materials for high temperature or high pressure service and other special purpose applications. It is a standard specification that defines typical chemical composition, mechanical properties, hardness requirements, preferential heat treatment, product marking, certification, and other requirements for bolted connections used in pressure vessel service, valves, flanges, and fittings. ASTM A193 defines SI (metric) and inch-pound units.

Chrome moly alloy flanges connect pipes, valves, pumps and other equipment, forming a piping system.

This ASTM A182 alloy steel flange has a smaller thickness for easier placement of bolt holes. These ASTM A182 F12 alloy steel pipe flanges are suitable for high temperature and high pressure environments.

Blind flanges have the face thickness of a flange, a matching face type, and similar bolting pattern.

The material contains carbon, manganese, phosphorus, sulfur, silicon, 8% chromium and molybdenum in a mixture. SA 335 grade P5 alloy steel pipe has similar strength to most austenitic stainless steel grades, with a minimum yield strength of 205MPa and a minimum tensile strength of 415MPa.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P120

ASTM A193 Grade B7 is the standard material specification for chromium-molybdenum alloy steel fasteners for high-strength, high-temperature, and special-purpose applications. Grade B7 is a heat treated chromium molybdenum alloy steel with a minimum tensile requirement of 100 ksi, a yield strength of 75 ksi and a maximum hardness of 35 HRC. The ASTM A193 specification covers requirements for chemical composition, mechanical properties, hardness, heat treatment, and recommended nut washers for Class B7 fasteners. ASTM A193 Grade B7 is the broadest specification for fasteners, commonly found in bolts or pipes, pressure vessels, valves, flanges and fittings.

The product portfolio is designed to be durable plumbing components, a sustainable alternative with premium quality that aids business growth.

A182 Gr F1 threaded flange is widely requested, also known as threaded flange, it has a thread in the flange hole, it is installed on the pipe, it matches the external thread on the pipe.

ASTM A182 Grade F5 Flanges are suitable for connecting pipes of small bore size and without the requirement of welding. ASTM A182 GR F5 Flange belongs to the ASTM A182 specification. The dimensions of the flanges vary according to the ANSI, ASME and DIN standards. The flange sizes range from ? inches to 36 inches in nominal bore sizes. Navstar Steel is a leading supplier and manufacturer of these flanges in various sizes and types.

Compared to other manufacturing process, ASTM A182 F22 Metal forging is mainly focused on producing some of the strongest manufactured parts. It¡¯s not just limited to iron and steel forging but as well as other metals also.

Alloy steel F12 square bars can withstand very high temperatures with minimal product aging even after thousands of operating hours,

ASTM A335 P22 pipe specifications include seamless “chrome molybdenum” alloy steel pipe and alloy steel pipe. Chromium is an important compound in stainless steel. Any steel with 12% or more chromium is considered stainless steel. Unrivaled chromium resists oxidation at high temperatures.

ASTM A182 F11 flange has various dimensions and sizes such as 1/2″ to 36″. This is used in class like 150#, 300#, 600# and many more.

When the carbon content of the a333 gr 6 welded pipe chemistry is lower, the chance of cracking in the welded area is also lower. However, some manufacturers prefer seamless pipes over welded pipes. The reason behind this is that the performance of the a333 gr 6 seamless tube is almost 20% higher than the welded one in high pressure environments.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.57

The ANSI B16.5 Alloy Steel Slip On Flange is a flange type that allows the pipes to slip onto the flange and makes the connection in a precise locations.