dn350 alloy pipe fitting flange ring type joint flange A182 F11 plate flange

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

HastelloyC-276 (Hastelloy) is a tungsten-nickel-chromium-molybdenum alloy with extremely low silicon-carbon content and is considered to be an all-around corrosion-resistant aluminum alloy. The key moisture-resistant chlorine, various air-oxidizing fluorides, isopropyl titanate solutions, hydrochloric acid and air-oxidizing salts, have good corrosion resistance in ultra-low temperature and standing temperature sulfuric acid. Therefore, in the past 30 years, it has been widely used in extremely corrosive natural environments such as chemical plants, petrochemicals, flue gas desulfurization, pulp and paper industry, and environmental protection.

Corrosion resistance

The aluminum alloy has the following characteristics: 1. It has good corrosion resistance to most corrosive substances under the two conditions of air oxidation and repair. ¢ÚIt has good resistance to pitting corrosion, void corrosion and intergranular corrosion. The higher content of Mo and Cr makes the aluminum alloy resistant to corrosion by chloride ion content, and the W element further improves the corrosion resistance. At the same time, Hastelloy C-276 aluminum alloy is one of the only types of raw materials that are resistant to wet chlorine, hypochlorite and chlorine dioxide saturated solutions. Ester solution has obvious corrosion resistance. It is one of the very few raw materials that can be used as a hot sulfuric acid saturated solution.

It is available in materials of ASTM A 182, and ASTM A 105. The flanges are available in various grades like ASME B16 47 ¡®A¡¯ Series, and ¡®B¡¯ Series to suit the needs of the clients and the industry.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Chrome molybdenum flanges provide higher levels of chromium and molybdenum. The added chromium helps improve the hardenability and corrosion resistance of the steel, while the added molybdenum helps to enhance its toughness and corrosion resistance.

SA 182 Socket Weld Flanges are joined by inserting the pipe into the socket end and applying a fillet weld around the top. This allows for better flow of fluid or gas inside the pipe and smooth holes.

ASTM A182 is the Standard Specification for Forged or Rolled Alloy Steel Pipe ASTM A182 F11 Flanges, Forged Fittings, and Valves and Parts. These alloy steel A182 grade F11 WNRF flanges are designed for high temperature applications.

WPHY 52 chemical composition are known for accurate dimension, corrosion resistance and their durability.

ASTM A335 pipes (P5, P9, P11, P22, P91 pipes) are known as chrome molybdenum alloy pipes and have been widely used in high temperature and high pressure services in different industries. According to market data, it is one of the most consumed alloy pipes in the boiler industry, heat exchangers, power stations, high pressure and ultra-high pressure vessels.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P115

The alloy has great mechanical properties at subzero temperatures.For catering to the needs of our customers better, it is essential that we manufacture Monel Pipe Fittings in different types, with each one serving some specific purpose.

We are Leading Manufacturers of Alloy Steel ASTM A182 F22 Flange & have huge stock of Class 150, Class 300, Class 400, Class 600, Class 900, Class 1500# & Class 2500.

Despite adding these elements, low alloy steel flanges aren’t necessarily difficult to weld. The key to achieve a successful performance of the welding operation is by knowing exactly what type of low-alloy steel you have.

These fittings are available in different types such as elbows,couplings,tees crosses,plugs,pipe nipples etc.

B7 y B7M se trataran termicamente mediante enfriamiento rapido y revenido en un medio liquido. Para los sujetadores B7M, el tratamiento termico final, posiblemente una operacion de templado si se realiza a un minimo de 1150 ¡ãF [620 ¡ãC], debe realizarse despues de todas las operaciones de mecanizado y formacion, incluido el laminado de roscas y cualquier tipo de corte. Preparacion de la superficie que permite realizar pruebas de dureza, evaluacion no destructiva o tension ultrasonica de pernos.

Chromium Molybdenum Alloy Steel or Chromium Molybdenum, CrMo is an alloy steel used for high temperature and high pressure service. Chromium molybdenum is used in power generation and petrochemical industries for its tensile strength, corrosion resistance and high temperature strength.

We use tested and qualified raw materials to improve the machinability of alloy tubes. These are processed through a metallization process that refines structural and material defects.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.37

Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

ASTM A193 B7 bolts are manufactured to meet numerous specifications and material design properties. More specifically, B7 alloy steel is a high temperature grade of A-193. B7 steel is also a chromium molybdenum steel with a minimum tensile strength of 125ksi.

It is the addition of other elements that make alloy steel stronger. Heat-treated elements such as silicon and manganese give alloy steels improved properties and additional benefits, such as increased corrosion resistance or improved weldability.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.49

Alloy Steel AISI 4140 bar stock or forging stock to produce B7 headed and non-headed bolts. A193 Grade B7 is the most commonly used Bolt specification coupled with A194 Grade 2H Nuts for Bolting Carbon Steel pipeline. A193 B7 bolting is available in metric sizes from M6 to M180 and imperial sizes from 1/4 to 7 inches, in diameter.

La especificacion ASTM A193 Grado B7 cubre los requisitos para materiales de empernado de acero aleado de alta resistencia para servicio de alta temperatura o alta presion y otras aplicaciones de proposito especial. Es una especificacion estandar que define la composicion quimica tipica, las propiedades mecanicas, los requisitos de dureza, el tratamiento termico preferencial, el marcado del producto, la certificacion y otros requisitos para las conexiones atornilladas utilizadas en el servicio de recipientes a presion, valvulas, bridas y accesorios. ASTM A193 define unidades SI (metricas) y pulgadas-libras.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

The key to the P5 composition of chromium-molybdenum alloys is the addition of chromium and molybdenum. Chromium or chromium increases high temperature strength, increases oxidation resistance and increases tensile, yield and hardness at room temperature. Molybdenum improves strength, elastic limit, wear resistance, impact quality and hardenability. It increases resistance to softening, inhibits grain growth, and makes chrome steel less susceptible to embrittlement. Molybdenum is also the most effective additive for increasing high temperature creep strength or creep resistance. It also enhances the corrosion resistance of the steel and inhibits pitting corrosion.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P107

ASME SA182 F5 pipe flange weight depends on wall thickness and nominal bore. The wall thickness of the flange is determined by the pressure rating.

ASTM A182 Low Alloy Steel flanges as well as the other types of alloys. The ASTM A 182 specification specifies flanges for high pressure services.

The production of ASME SA182 F9 flanges will be done using alloys with lower carbon content. Reducing the carbon content in these alloys reduces the formation of carbide precipitates. This basically means that alloy steel F9 flanges will no longer be susceptible to intergranular corrosion in the heat affected weld zone.

The carbon form can be iron carbide or Alloy Steel F9 Weld Neck Flanges can be carbide of an alloying component, for example, titanium. The A182 F9 Steel Slip On Flanges are good for use with seamless pipes because the flanges allow for the pipes to slip onto them for precise location for the connection.

ASTM A320 bolts are suitable for low temperature service down to -150¡ãF and have a minimum Charpy impact value of 20-ft-lbf at this temperature. ASTM A320 Hex Bolts must obtain the durability and service of high temperature or high pressure and corrosion resistant steel. ASTM A320 Stud Bolts are available in different sizes and patterns, our premium ASTM A320 Grade L7 AS Bolts are in high demand in the market due to their speculative properties and specifications.

ASTM A182 F5 Lap Joint Flanges go by a range of names, including back up flange, loose hubbed flange, loose ring flange and van stone flange. ASTM A182 F5 Flanges is a method of connecting pipes, valves, pumps and other equipment to form a piping system. It also provides easy access for cleaning, inspection or modification. Flanges are usually welded or screwed. Flanged joints are made by bolting together two flanges with a gasket between them to provide a seal.

ASTM A335 P91 Seamless Pipe is one of the seamless pipes that standardize A335 in various industries. ASME SA 335 Grade P91 Alloy Steel Pipe is made of chrome molybdenum alloy. These pipes contain 1% molybdenum, 9% chromium and nickel, manganese, silicon and carbon. ASTM A335 P91 pipe has very high tensile strength, yield strength, impact cracking resistance, corrosion cracking resistance and oxidation resistance.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.23

Shaped flanges made by die forging or precision (lost wax) casting, depending on the mechanical properties of the flange, die forged flanges have higher strength than cast flanges. Precision profiled flanges manufactured by forging or casting require a model (tool).