Duplex 2205 hex bolt and nut S32205 M10-M24 bolt manufacturer

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

Duplex steel UNS S31803, UNS S32205 round rods and wires are widely used in chemical, oil and gas, fertilizer and other application industries.

Duplex steels have the best resistance to pitting corrosion. This steel has effective fatigue strength to resist corrosion of the steel. The steel can be used in a wide range of heating temperatures in the industry.

Phase stainless steel UNS S31803 fasteners exhibit the properties of austenitic and ferritic stainless steels. UNS S31803 dual phase steel fasteners have high strength, good resistance to sulfide stress corrosion and excellent impact toughness.

The notch ductility of SA 240 S32760 Sheet performs well at sub-zero temperatures, down to the -50¡ãC range, while performing well at ambient temperature.

ASTM A1082 specification alloy S31803 fasteners have higher pitting and crevice corrosion than stainless steel alloy 316. Due to its higher corrosion resistance, alloy grade UNS S31803 is able to exhibit better fatigue strength than other commonly used austenitic stainless steel grades in environments containing corrosive media.

The inclusion of chromium imparts good corrosion resistance to austenitic grade 304. However, increasing the chromium content to about 25%, as in the case of 2205 duplex stainless steel pipe makes the alloy resilient across several media.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

This increase in alloyants is what gives the super duplex stainless steels greater corrosion resistance properties.

Duplex 2205 bolts (EN 1.4462 ) are made of austenitic-ferritic stainless steel and are designed to provide higher strength and corrosion resistance than 300 series stainless steels. It helps users avoid stress corrosion cracking common to 316 and 317. Duplex 2205 bolts combine the stress corrosion cracking resistance and high strength of ferritic alloys with austenitic fabrication capabilities.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

ASTM A789 A789M Covers Grades of nominal wall thickness, stainless steel tubing for services requiring general corrosion resistance, with particular emphasis on resistance to stress corrosion cracking. These steels are susceptible to embrittlement if used for prolonged periods at elevated temperatures.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The granular structure of duplex is a ferrite-austenite hybrid with a superior strength to weight ratio in comparison to 304 or 316. It balances the weldability of an austenitic with a pure ferritic and retains decent mechanical toughness in applications with exposure to colder ambient temperatures.

The advantage of the dual-phase structure is that it combines the advantages of ferritic alloys (resistance to stress corrosion cracking and high strength) with the advantages of austenitic alloys (ease of manufacture and corrosion resistance). The service temperature of 2205 duplex stainless steel should be limited to below 600¡ãF. Prolonged exposure to high temperatures can make 2205 stainless steel brittle.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.67

Duplex stainless steel, alloy 2205 was designed as comprising 22% chromium, 3% molybdenum, and 5-6% nickel nitrogen. Alloy 2205 combines the desirable aspect of properties of both austenitic and ferritic grades.

In S31803, about half of the ferrite grains transform into austenite grains (“islands”) as the material cools to room temperature. The result is a microstructure of approximately 50% austenite and 50% ferrite.

Duplex 2205 stainless steel (ferritic and austenitic) is widely used in applications requiring good corrosion resistance and strength.

Duplex alloys prove themselves useful in applications where ordinary steel grades are susceptible to failure. The microstructure of the Duplex Pipe Material partially consists of both austenite and ferrite regions.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Some steels also contain Mo, Cu, Nb, Ti, N and other alloy elements. Compared with ferrite, it has higher plasticity and toughness, no room temperature brittleness, significantly improved intergranular corrosion resistance and welding performance, and maintained 475 ¡æ brittleness, high thermal conductivity and Superplasticity of ferritic stainless steel. Compared with austenitic stainless steel, its yield strength is significantly improved, and its resistance to intergranular corrosion, stress corrosion, corrosion fatigue and abrasion is significantly improved.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Duplex stainless steels are approximately 50% ferrite and 50% austenite for optimum strength and corrosion resistance.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

The astm a182 f53 vs f55 can come in different diameters ranging from ? inches to 48 inches with different pressure classes ranging from class 150 through class 2500.

The material has high strength and corrosion resistance. The A182 F53 material is used to make flanges ranging from 1/2 inches to 48 inches under different standards such as ANSI, ASME, DIN and other international standards.

Compared with austenitic stainless steel, F51 duplex stainless steel has twice the compressive strength, and compared with 316L and 317L, the designer can reduce its weight.

From corrosion resistance to strength, businesses around the world appreciate these properties of 2507 Super Duplex Seamless. Due to the dual microstructure phase, the weldability of this alloy is classified as good, which is why a relatively robust and durable super duplex welded pipe can be achieved.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.41

Grade 904L is less resistant to nitric acid than grades 304L and 310L, which are free of molybdenum. This steel grade needs to be solution treated following cold working, to achieve maximum stress corrosion cracking resistance under critical environments

ASTM A479 Duplex Stainless Steel 1.4462 Punched Gaskets are SCC resistant which is prominent in many applications such as hot water tanks, brewing tanks, desalination plants and processing plants. Therefore, ASTM A479 Duplex Stainless Steel UNS S31803 Lock Washers exhibit the properties of ferritic and austenitic alloys.

The flanges could also be manufactured as screwed, threaded or forged types. The forged flanges are made from a single piece of raw material. These are also called the cast flanges.

The duplex microstructure allows this grade of high strength super duplex UNS S32750 bar to have a lower coefficient of thermal expansion and higher thermal conductivity than austenitic steels and is suitable for operating temperatures up to 300¡ãC.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

The steel has excellent resistance to chloride stress corrosion cracking, high thermal conductivity and a low coefficient of thermal expansion. The high chromium, molybdenum, and nitrogen levels provide excellent resistance to pitting, crevice, and general corrosion.