Duplex S31803 S32205 plate about twice that of austenitic stainless steels

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

2507 is used for oil and gas industry equipment, offshore platforms, heat exchangers, process and service water systems, fire-fighting systems, and injection and ballast water systems.

Additionally, Duplex 2205 is the most widely used duplex grade on the market. Duplex 2205 alloy is a nitrogen-enhanced duplex stainless steel alloy. The effect of nitrogen is to significantly increase the corrosion resistance of the alloy; especially in the as-welded condition.

The notch ductility of SA 240 S32760 Sheet performs well at sub-zero temperatures, down to the -50¡ãC range, while performing well at ambient temperature.

Duplex 2205 was tested under reverse bending stress at room temperature compared to SS316. The results show that Duplex 2205 has approximately twice the fatigue limit/yield strength.

Some of the typical applications of duplex steel grade 2205 are oil and gas exploration, processing equipment, transport, storage and chemical process, high chloride and marine environments, paper machines, liquor tanks, pulp, and paper digesters.

Due to the alloy’s strong resistance to chemical compositions including acids, bases and neutral solutions, duplex steel uns s31803 nuts would be an ideal addition to these industries.

Astm A790 Uns S31803 grade pipes and tubes can be cold-rolled to give them enhanced properties and good resistances in different systems.

The material has high strength and corrosion resistance. The A182 F53 material is used to make flanges ranging from 1/2 inches to 48 inches under different standards such as ANSI, ASME, DIN and other international standards.

Duplex plates have a two-phase or two-phase microstructure. The microstructure of the duplex steel S32205 foil consists of equal proportions of ferrite and austenite.

The high oxidation resistance property of Grade 2205 is marred by its embrittlement above 300¡ãC. This embrittlement can be modified by a full solution annealing treatment. This grade performs well at temperatures below 300¡ãC.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The corrosion resistance properties of Duplex 2205 Pipe is much better as compared to alloy grade 316.

UNS S31803 Bolt is a threaded fastener with external threads. Generally, like screws, alloy S31803 bolts tend to use a variety of head designs.

ASTM A815 specification covers two general classes, WP and CR, of wrought ferritic, ferritic/austenitic, and martensitic stainless steel fittings of seamless and welded construction. Class WP fittings are subdivided into four subclasses: Classes WP-S, WP-W, WP-WX, and WP-WU. The material for fittings shall consist of forgings, bars, plates, or seamless or welded tubular products.
Teel Industry has grown in the past few decades and there are a variety of products available in the market. ASTM A815 UNS S32750 Pipe Fittings are one of those products and are available in various sizes, shapes, and dimensions. ASTM A815 UNS S32760 Pipe Fittings are designed to be resistant to corrosion and are said to have perfect weldability. These Super Duplex S32750 Buttweld Fittings are resistant to erosion corrosion and fatigue. They have a mixed microstructure of 50% austenitic and 50% ferrite.

Astm A479 Super Duplex Steel UNS S32760 Hex Bolts have a high PREN value, the rate of pitting is lower, despite the use of these fasteners in highly corrosive environments such as oil wells and pipelines transporting soured oils, sulfide ores processing, kraft paper production plants, methionine and lysine factories, as well as the photographic industry.

Alloy 2205 UNS S32305/S31803 is a 22% chromium, 3% molybdenum, 5-6% nickel, nitrogen alloyed Duplex Stainless Steel Pipe with high general, localized, and stress corrosion resistance properties in addition to high strength and excellent impact toughness.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Duplex Stainless Steel offers excellent resistance to corrosion along with very high mechanical strength, which allows for lighter fabrication and greater design flexibility. With this high corrosion resistance, Duplex Stainless Steel provides more uptime than Carbon Steel or conventional Stainless Steel.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The steel has excellent resistance to chloride stress corrosion cracking, high thermal conductivity, and a low coefficient of thermal expansion.

Compared to conventional stainless steels, duplex steel pipes guarantee higher resistance to pitting and stress corrosion cracking. Meanwhile, our ASTM A 789/A 790 Duplex Steel Pipes and Tubes are available in different sizes, gauges and thicknesses according to customers’ customized requirements.

HT PIPE is the government certified and doing business in steel industry for long years and are manufacturing S32750 Duplex buttweld fittings at affordable rates.

The chemistry of this steel ensures better performance with higher mechanical properties in comparison to austenitic stainless steel pipes.

This category of material includes grades 2205, F51, F53, and F60. Duplex stainless has increased in popularity over the years due to its excellent chemical and mechanical properties versus their basic stainless counterparts, given especially that the cost differences are minimal now as the availability has increased.

Compared with ferritic stainless steel and austenitic stainless steel, duplex stainless steel pipe has good welding performance. It is neither like the welding heat affected zone of ferritic stainless steel, because of the grain coarsening, the plastic toughness is greatly reduced, nor like austenitic stainless steel, it is more sensitive to welding hot cracks.

In general, duplex steel S31803 plate can be used as a replacement for the rather expensive stainless steel alloy grade 904L, as 2205 SS plate has similar properties but is less expensive in composition.

It is also exceptionally resistance to chloride SCC. Flanges are supplied with pitting resistance equivalent that is assuring very good pitting corrosion resistance.

Preheating of UNS S32750 Super Duplex Fasteners is not necessary except to prevent condensation on cold metal.

We offer a complete range of 2205 Duplex Steel Fasteners such as Bolts, Nuts, Washers, Screws, Connecting Rods and Duplex Steel Screws. We also offer super duplex fasteners in different sizes, shapes, features and thicknesses according to customer requirements.

 ANSI B16.5 Super Duplex Stainless Steel S32750 Orifice Flange provides excellent resistance to a wide range of corrosive environments, including seawater, acidic solutions, and chloride-containing environments. Super Duplex F53 WN Flange exhibits higher corrosion resistance than standard duplex stainless steels.

The structure of 2205 duplex stainless steel consists of a pool of austenite surrounded by a continuous ferrite phase. In the annealed condition, 2205 contains approximately 40-50% ferrite. 2205 is often referred to as the workhorse grade and is the most widely used grade in the duplex stainless steel family.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.49

2205 duplex stainless tubing material, which is why it is referred to as a self-repairing layer.

It reaches the phase balance of austenite and ferrite in roughly same volume fraction.