duplex stainless steel pipes diameter 200 mm

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

ASTM A312 TP316 is a standard specification for seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipes used in high-temperature and general corrosive service applications. The 316 Seamless Industrial Steel Pipe is made from a combination of chromium, nickel, and molybdenum, which gives SS 316 Seamless Tube excellent resistance to corrosion and rust.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

304 Piping Spools are made of 304 Stainless Steel, a common and popular material in many industrial applications that require resistance to corrosion and oxidation. These S30400 Piping Spools are prefabricated using specialized machinery and processes, which ensure that they are highly accurate and reliable.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

Inconel 718 is a nickel-chromium-based alloy that is commonly used in high-temperature applications such as aerospace and gas turbines. One of the most important factors in the production of ASTM B670 Inconel 718 Sheet is the plate rolling process. There are two main types of Inconel 718 plates available on the market: hot rolled and cold rolled plates.

ASME B36.19M is the standard specification for stainless steel pipes, which specifies the dimensions, tolerance, and manufacturing requirements for both welded and seamless pipes.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

The material has carbon, manganese, phosphorus, sulfur, silicon, copper, nickel, chromium, molybdenum and vanadium in its composition.There are also different types based on the shapes. The carbon steel a105 blind flange is a very special type.

G30 alloy can prevent the formation of grain boundary precipitation in the heat affected zone of welding, so its welded products are suitable for various chemical treatment engineering applications.

There are also different standards that govern the nominal bore sizes of the flanges. The ANSI B16.5 SS 309S Blind Flange is a blind flange that is used to close a connection.

904L (N08904, 14539) super austenitic stainless steel contains 14.0-18.0% chromium, 24.0-26.0% nickel, 4.5% molybdenum. 904L super austenitic stainless steel is a low-carbon, high-nickel, molybdenum austenitic stainless acid-resistant steel, which is a proprietary material imported from French H¡¤S Company. It has good activation-passivation transformation ability, excellent corrosion resistance, good corrosion resistance in non-oxidizing acids such as sulfuric acid, acetic acid, formic acid, phosphoric acid, and good corrosion resistance in neutral chloride-containing media Excellent pitting corrosion resistance, as well as good crevice corrosion resistance and stress corrosion resistance. It is suitable for various concentrations of sulfuric acid below 70 ¡ãC, and has good corrosion resistance in acetic acid of any concentration and temperature under normal pressure, as well as in the mixed acid of formic acid and acetic acid.

ASTM B564 UNS N04400 Slip on Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Type 316 stainless steel has a higher nickel content than 304 stainless, plus molybdenum, for greater corrosion resistance from caustic chemicals, corrosive fluids, oils, and gases, and withstands pressure and high temperatures. 304 pipe connects with fittings to transport air, water, natural gas, steam, and chemicals to storage tanks and in residential plumbing, and kitchen and food applications.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Alloy steel pipe is made of iron base. It has a complete austenite structure and has good corrosion resistance to various corrosive media. These pipes and tubes are the most cost-effective option for long-lasting applications.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.32

ASTM A240 is a normative standard covering several chromium-based stainless steel grades manufactured in sheet, sheet, or ASTM A240 Gr 2205 strip.

Mild steel, it is a type of carbon steel. Carbon is present in all steels and when carbon is the main alloying element in steel it is called carbon steel. On the other hand, the amount of carbon present in the steel determines the type or grade of carbon steel. Mild steel has the lowest carbon content of any steel, but that doesn’t make it less useful. In fact, mild steel is the most commonly used steel grade, accounting for 85% of total U.S. steel production.

Usually, these applications are pressure systems, and it is seen in many instances, the ASTM A105 Threaded Fittings add value to said application.

HT PIPE stocks seamless and welded 304/304L stainless steel pipe. This grade of steel is the most widely used grade due to its resistance to corrosion and oxidation. Some of the benefits of choosing this material for piping include its low maintenance costs, ability to withstand harsh environments, and weldability. Type 304 and 304L stainless steel pipes perform well in high temperatures and harsh environments. This type of steel is very durable and can be used in a wide range of applications and industries.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.27

In our Mumbai Facotry, we produce long radius (LR, LRE) A234 Pipe Elbow the radius of curvature is 1.5 times the diameter (R=1.5D).

Astm B564 Uns N06601 Flanges Inconel 601 is a nickel-chromium alloy used for applications that require resistance to corrosion and heat. This nickel alloy stands out due to its resistance to high temperature oxidation, remaining highly resistant to oxidation through 2200¡ã F. Alloy 601 develops a tightly adherent oxide scale which resists spalling even under conditions of severe thermal cycling.

Class 150 Monel 400 RTJ Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Inconel 718 flanges are also available to our customers in different sizes and shapes. These Inconel 718 Socket Weld Flanges are also used in jet engines, pump bodies and parts, rocket engines and thrust reversers, nuclear fuel element gaskets, hot extrusion tools and more.

The astm a182 f53 vs f55 can come in different diameters ranging from ? inches to 48 inches with different pressure classes ranging from class 150 through class 2500.

ASTM A479 Duplex Steel UNS S31803 Nuts have excellent general corrosion resistance in a variety of aggressive chemicals including seawater and industrial acids. The microstructure of ASME SA 479 Duplex Steel UNS S32205 Hex Nuts consists of a mixture of austenitic and ferritic phases. Therefore, it exhibits the properties of austenitic and ferritic stainless steels.

Stainless steel sanitary fittings are the main components of sanitary process systems. As one of the sanitary solution providers, HT PIPE manufactures and supplies a wide range of sanitary fittings including DIN/SMS/3A/IDF/RTJ/ISO/BS welded fittings, unions, tri-clamps, ferrules, pinch fittings and short tube etc. We have the ability to provide qualified sanitary fittings that meet your high purity conditions and FDA, GMP requirements.

Stainless steel UNS S30400 round bars are used to grow a variety of utensils, chemical equipment, cookware and loads of various digital and electrical machinery and parts. They are also used in the cement industry, shipbuilding industry, petrochemical industry, chemical industry, sugar mills, etc.
We use the best metal alloys available to manufacture the round bars and their finish is clean and precise.

SA 240 UNS S32760 Sheet For ships, tanks and containers, for deployment on most surfaces around metal lattices.

They are ideal for applications carrying corrosive or high-temperature fluids or gases. Industries that could benefit from chrome moly flanges include: Oil and Gas, Refinery, Power Generation, and Chemical Processing.

304 stainless steel has good oxidation resistance in intermittent use up to 870¡ãC and continuous use up to 925¡ãC. However, if corrosion resistance in water is required, continuous use at 425-860¡ãC is not recommended. In this case, 304L is recommended because of its resistance to carbide precipitation.

Stainless Steel Duplex SAF 2205 Hex Bolts are used in machinery and construction and can be used with nuts or threaded holes. Since they can be tightened with a wrench, fully threaded hex bolts are specially designed to work more efficiently. Additionally, 2205 hex bolts are stronger than standard stainless steel, meaning they can be used for jobs that require high workloads and good corrosion resistance.

Inconel 625 bar can withstand high stress and a wide range of temperatures, in and out of water, as well as resist corrosion when exposed to highly acidic environments, making it ideal for marine and nuclear applications.

This alloy is not suitable for highly oxidizing acids such as nitric acid and nitrous acid. It is resistant to sulfuric acid up to 80% and hydrochloric acid solutions up to 20%.

Due to the material composition, the strength and the corrosion resistance, these flanges are used in a variety of applications.

Grade 310S Stainless Steel Butt Weld Pipe Fitting contains low Carbon, with higher Nickel and Chromium content curbing Hydrogen sulphide attack, which used in various industries like heat exchangers, furnace parts, shipbuilding, heat treatment baskets, condensers, offshore etc.
The fittings are shaped up and then heated to a high temperature following a rapid cooling closer to the cooling in still air. This rapid cooling adds to the strength of the Stainless Steel 310 Pipe Fittings and makes them much stronger. The SS 310S Fitting is used in industries like the sea water processing, thermal energy generation plants and much domestic piping as well. 310S SS Weld Fittings is used in different pressure classes to cope up with the pressure containment requirement of the application as well.

Type 304 stainless steel is a T 300 Series Stainless Steel austenitic. It has a minimum of 18% chromium and 8% nickel, combined with a maximum of 0.08% carbon. It is defined as a Chromium-Nickel austenitic alloy.304 stainless steel is used for a variety of household and industrial applications such as food handling and processing equipment, screws,[3] machinery parts, utensils, and exhaust manifolds. 304 stainless steel is also used in the architectural field for exterior accents such as water and fire features. It is also a common coil material for vaporizers.

Our 4310 seamless pipes implement strict quality specifications and strictly follow every level of production. So this allows us to take our quality goals to a higher level. Every product is tested to national and global quality standards. In addition, we also provide customers with specific tests according to their application requirements.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.39

Monel nickel-copper alloy K-500 pipe bend and elbow combine the excellent corrosion resistance characteristic of Monel alloy 400 with the added advantages of greater strength and hardness.