Duplex Stainless Steel S31083 S32205 Flanges work in high-pressure conditions

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

S31803 stainless steel is a nitrogen alloy duplex stainless steel containing 22% chromium, 3% molybdenum, and 5-6% nickel. In addition to high strength and excellent impact toughness, it also has high resistance to general corrosion, localized corrosion and stress. Corrosive properties.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.61

It reaches the phase balance of austenite and ferrite in roughly same volume fraction.

The steel has excellent resistance to chloride stress corrosion cracking, high thermal conductivity and a low coefficient of thermal expansion. The high chromium, molybdenum, and nitrogen levels provide excellent resistance to pitting, crevice, and general corrosion.

The temperature in heat exchange is usually increased because they work according to the principle of heat transfer. While A789 tubing can hold its own at high temperatures, it is not recommended for use in temperatures above 600F. Duplex 2205 Tube may become brittle and rot at temperatures above 600F.

ASTM A240 UNS S32750 Plate is a stainless steel alloy with excellent resistance to chloride stress-related corrosion cracking.

Duplex stainless steels have a microstructure which is 50% ferritic and 50% austenitic. This composition gives them a better strength than either ferritic or austenitic steels. Further details about this topic are given below (see ASTM A790 pipes).

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

ASTM A182 Grade F51 is the standard duplex stainless steel and is also called ¡°duplex 2205¡± or ¡°alloy 2205¡±.

2507 Duplex Plate also exhibit better ductility and toughness compared to ferritic stainless steels, but they do not provide these properties as successfully as austenitic stainless steels.

2205 has excellent corrosion properties, and it is well-suited to environments containing chlorides and hydrogen sulphide, for use in oil and gas extraction from sour wells, in refineries and in process solutions contaminated with chlorides.

The duplex material contains bot the austenitic and ferrite structures in the metallurgy of the material. These properties bring the material the best of both ferritic and austenitic steel types. The pipes could be hot rolled or cold drawn. The hot rolled ones are stronger and the cold drawn ones are seamless and accurate in dimensions. The Duplex Seamless Pipe is used in applications with high precision requirements.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Material: Duplex Steel ASTM A789 S31803,S32205,S32750, S32760
ASTM A790 S31803,S32205,S32750, S32760

The yield strength is also higher, allowing component designers to reduce section size for load-bearing applications.

S31803 Duplex Steel is a 22% chromium duplex (austenitic/ferritic) steel with moderate to good strength and good general corrosion/stress corrosion/cracking resistance.

Duplex 2205 is a nitrogen enhanced duplex stainless steelthat was developed to combat common corrosion problems encountered with the 300 series stainless steels. ¡°Duplex¡± describes a family of stainless steels that are neither fully austenitic, like 304 stainless, nor purely ferritic, like 430 stainless. The structure of 2205 duplex stainless steel consists of austenite pools surrounded by a continuous ferrite phase. In the annealed condition, 2205 contains approximately 40-50% ferrite. Often referred to as the work horse grade, 2205 is the most widely used grade in the duplex family of stainless steels.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

While Duplex 2205 is the most common duplex product we supply, we can also deliver Duplex 2304 and Duplex 2207 with reduced lead times as these alloys are stocked. Alloy 2205 (UNS S32305/S31803) is a 22% chromium, 3% molybdenum, 5-6% nickel, nitrogen alloyed duplex stainless steel pipe with high general, localized, and stress corrosion resistance properties in addition to high strength and excellent impact toughness.

Alloy 2205 duplex stainless steel plate has better pitting and crevice corrosion resistance than 316L or 317L austenitic stainless steel in almost all corrosive media.

2507 is also used in Flue Gas Scrubbing Equipment, Pulp and Paper Mill Equipment, Offshore Oil production/technology and Oil and gas industry equipment.

The yield strength of this alloy is about 570 MPa. In addition to strength, A240 S32750 Super Duplex Plate is an alloy that provides the best resistance to crevice and pitting corrosion.

The high chromium, molybdenum, and nickel levels provide excellent resistance to pitting, crevice, and general corrosion.

UNS S32750 or DIN W.Nr. 1.4410, Duplex 2507 is a super duplex stainless steel conutaining 25% chromium, 4% molybdenum and 7% nickel, designed for demanding applications requiring exceptional strength and corrosion resistance, such as chemical Process, petrochemical and seawater equipmenut.

Supplied in the annealed condition, it has a yield strength of 80ksi (550Mpa), which is higher than most austenitic and duplex grades.

With an increased chromium content compared with F51 it offers improved pitting corrosion resistance.

Duplex Steel UNS S31803 Seamless Pipes are widely used in various applications in the industry. These ASTM A790 Duplex Steel S31803 Pipes are made up of a combination of microstructure of austenitic and ferritic grains, which gives them unique properties. These properties include a high resistance to corrosion, excellent strength and toughness, and good weldability.

The yield strength of 2205 is about twice that of austenitic stainless steel. This allows designers to reduce weight and make the alloy more cost-competitive compared to 316L or 317L.

Technically, the microstructure of a duplex 2205 tube is approximately 50% ferrite and 50% austenite. As a result, the properties inherited from both categories make this nitrogen-enhanced duplex 2205 seamless pipe ideal for use in industries such as food processing, oilfield piping and heat exchangers, and flue gas desulfurization.

Duplex 2205 bolts (EN 1.4462) are made from an austenitic-ferritic stainless steel, which was designed to deliver higher strength and corrosion resistance than 300 series stainless steels. It helps users to avoid stress corrosion cracking that is typically seen with 316 and 317. Duplex 2205 bolts combine the qualities of stress corrosion cracking resistance and high strength derived from being a ferritic alloy along with its austenitic fabrication capabilities.

The granular structure of duplex is a ferrite-austenite hybrid with a superior strength to weight ratio in comparison to 304 or 316. It balances the weldability of an austenitic with a pure ferritic and retains decent mechanical toughness in applications with exposure to colder ambient temperatures.

The advantage of the dual-phase structure is that it combines the advantages of ferritic alloys (resistance to stress corrosion cracking and high strength) with the advantages of austenitic alloys (ease of manufacture and corrosion resistance).

Alloy 2205 UNS S32305/S31803 is a 22% chromium, 3% molybdenum, 5-6% nickel, nitrogen alloyed Duplex Stainless Steel Pipe with high general, localized, and stress corrosion resistance properties in addition to high strength and excellent impact toughness.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”