Duplex2205 1.4462 S31803 washer DIN125

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

ASTM A312 TP316 is a standard specification for seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipes used in high-temperature and general corrosive service applications. The 316 Seamless Industrial Steel Pipe is made from a combination of chromium, nickel, and molybdenum, which gives SS 316 Seamless Tube excellent resistance to corrosion and rust.

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

ASME B36.19M is the standard specification for stainless steel pipes, which specifies the dimensions, tolerance, and manufacturing requirements for both welded and seamless pipes.

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

316L 1.4401 S31603 Stainless Steel Pipe is a highly versatile and durable pipe option commonly used in a wide range of industrial and commercial applications. This SS UNS S31603 pipe is made from high quality 316L stainless steel with excellent resistance to corrosion, oxidation and staining, making it ideal for harsh environments or high stress applications.

Nickel 200 flanges The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

304 Piping Spools are made of 304 Stainless Steel, a common and popular material in many industrial applications that require resistance to corrosion and oxidation. These S30400 Piping Spools are prefabricated using specialized machinery and processes, which ensure that they are highly accurate and reliable.

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Phase stainless steel UNS S31803 fasteners exhibit the properties of austenitic and ferritic stainless steels. UNS S31803 dual phase steel fasteners have high strength, good resistance to sulfide stress corrosion and excellent impact toughness.

Steel flanges provide an easy access for cleaning, inspection or modification. They usually come in round shapes but they can also come in square and rectangular forms. The flanges are joined to each other by bolting and joined to the piping system by welding or threading and are designed to the specific pressure ratings; 150lb, 300lb, 400lb, 600lb, 900lb, 1500lb and 2500lb.

A flange can be a plate for covering or closing the end of a pipe. This is called a blind flange. Thus, flanges are considered to be internal components which are used to support mechanical parts.

Alloy 400’s alkali resistance makes it ideal for deployment in highly acidic environments such as salt water, sulfuric acid or hydrofluoric acid.

309 stainless steel is a type of austenitic stainless steel that is often used in high-temperature applications due to its excellent heat resistance. SA240 309 plate contains a high percentage of chromium and nickel, which gives it good corrosion resistance, as well as a high degree of strength and durability. SS 309 Strip (UNS S30900) is an austenitic stainless steel developed for use in high temperature corrosion resistance applications. The SA240 309 plate resists oxidation up to 1900°F (1038°C) under non-cyclic conditions. Frequent thermal cycling reduces oxidation resistance to approximately 1850°F (1010°C).

ASTM A193 Grade B7 bolts are made of chrome-molybdenum material with high tensile strength and good elongation properties.

Incoloy 800H is a high carbon grade of these 800 alloys. These alloys exhibit excellent resistance to post-weld carburization and graining. They remain ductile for extended periods of time at temperatures below 700 degrees Celsius.

UNS N08031 Nut is a nitrogen-added iron-nickel-chromium-molybdenum alloy. Also known as WNR 1.4562 Nuts, its pitting resistance in high chloride environments is between super-austenitic stainless steels and nickel alloys. The alloy has very good corrosion resistance in mixed acid and high chloride environments. Typical applications for these nuts are control lines, heat exchangers, control and instrumentation pipes, etc. Industries that primarily use this grade are chemical processing, oil and gas, etc.

Alloy 800HT / Incoloy 800HT is a controlled composition derivative of INCOLOY alloy 800H (UNS N08810) and is used for the same creep resistant applications, however the combined effects of mechanical and thermal processing of the alloy permit higher design stresses to be incorporated than are permitted for the conventional alloy.

Werkstoff No.1.4436 316 stainless steel fittings are resistant to atmospheric corrosion, as well as moderately oxidizing and reducing environments. Corrosion resistant in polluted marine atmospheres. It has excellent resistance to intergranular corrosion.

For stainless steel plate, 304/304L dual certified stainless steel conforms to ASTM A240, as a stainless steel pipe manufacturer, we check in this regard, in fact, the chemical composition and properties are almost the same, dual certification is always required two very similar alloys, while Not very different grades like 304 and 321 stainless steel.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.36

If the 22cr Duplex Pipe is to be welded, no filler metal is required to be added to the alloy during its welding process.

These flanges have excellent corrosion resistance compared to 304 grade stainless steel flanges. We manufacture stainless steel 316L blind flanges of high quality for use in piping in critical conditions. This is an austenitic stainless steel.

Inconel 718 flanges have good resistance to oxidation and corrosion at temperatures within the effective strength range of the alloy in atmospheres encountered in jet engine and gas turbine operation.

This alloy is widely used in chemical and food processing, power generation, furnace components and many other market segments.

SS UNS S31600 Pipe Flanges Supplier
Featuring 304 stainless steel for very good corrosion resistance, this GRAINGER APPROVED weld neck flange can be attached to a system via a circumferential weld at the neck. The welded area can be easily examined by radiography. Matched pipe and flange bore reduces turbulence and erosion inside the pipeline. Flange is excellent for use in your critical applications and is ideal for use with air, water, oil, natural gas, and steam.

Stainless Steel 304 Spectacle Blind Flange, also known as a SS 304 Figure-8 Blind Flange or a paddle blind, is a special type of flange used in piping systems. SS 304 Spectacle Blind Flange is primarily used for isolating sections of a pipeline or for temporary closure during maintenance or inspection activities.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

ALLOYS STEEL SA 182 F9 BAR is a ferritic alloy steel bar, other contents are also considered. These bars are steel forged bars held at high temperature and pressure.

This grade has an excellent chemical combination of nickel, chromium alloys with high levels of iron, niobium and molybdenum and small amounts of aluminum and titanium.

Type 316/ 316L/316H are austenitic stainless steel intended for use in applications that require high strength, toughness and workability, as well as enhanced corrosion resistance.

A182 F53 material displays excellent corrosion resistance.

Type 304 stainless steel is a T 300 Series Stainless Steel austenitic. It has a minimum of 18% chromium and 8% nickel, combined with a maximum of 0.08% carbon. It is defined as a Chromium-Nickel austenitic alloy.304 stainless steel is used for a variety of household and industrial applications such as food handling and processing equipment, screws,[3] machinery parts, utensils, and exhaust manifolds. 304 stainless steel is also used in the architectural field for exterior accents such as water and fire features. It is also a common coil material for vaporizers.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

304 and 304L can be specified in annealed conditions with very good formability. Higher nickel versions can be specified for enhanced multi-stage deep drawing characteristics. For spring type applications, Types 304/304L can also be specified in higher strength cold work conditions. Type 304/304L is non-magnetic in the annealed condition, but may become slightly magnetic by cold working.
Type “Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size “OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”

The standards vary from B16.5, B16.47 and in different series A and B. There are different types based on the production such as the ASME SA182 grade 316TI Weld neck flange. The weld neck flanges are useful because of the neck welded onto the flanges, they allow for better grip. The different standards such as DIN 1.4571 Flange determine the size, diameter and wall thickness of the flanges.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

Incoloy 925 flanges are ideal for use in applications that require a combination of high strength and corrosion resistance.

Our UNS S31008 SS Weld Neck Flanges are customarily applicable to the process plants. Our SS 310 Flanges are 18-8 austenitic stainless steel flanges, with their Chromium-Nickel combination being heat resistant and oxidation resistant.

The strength, factorially speaking of an ASTM A790 UNS S31803 Seamless Pipe, is two times higher than that of either of the two stainless steel classes. And the toughness and ductility of the Sa 790 UNS S32205 Welded Pipe are better in comparison to ferritic steels.

Used in chemical and petroleum processing, in power plants for superheater and reheater tubing, in industrial furnaces, and for heat treating equipment.