GR.70N bleed ring sandblasting and embossed

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

Inconel 625 Coil is characterized by its excellent resistance to oxidation, high-temperature corrosion and fatigue. ASTM B443 UNS N06625 Inconel Plate is widely used in the aerospace, chemical processing and oil and gas industries due to its superior strength, toughness and durability even in extreme environments.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

304 Piping Spools are made of 304 Stainless Steel, a common and popular material in many industrial applications that require resistance to corrosion and oxidation. These S30400 Piping Spools are prefabricated using specialized machinery and processes, which ensure that they are highly accurate and reliable.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

ASTM A312 TP316 is a standard specification for seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipes used in high-temperature and general corrosive service applications. The 316 Seamless Industrial Steel Pipe is made from a combination of chromium, nickel, and molybdenum, which gives SS 316 Seamless Tube excellent resistance to corrosion and rust.

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

316L 1.4401 S31603 Stainless Steel Pipe is a highly versatile and durable pipe option commonly used in a wide range of industrial and commercial applications. This SS UNS S31603 pipe is made from high quality 316L stainless steel with excellent resistance to corrosion, oxidation and staining, making it ideal for harsh environments or high stress applications.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

Inconel 718 is a nickel-chromium-based alloy that is commonly used in high-temperature applications such as aerospace and gas turbines. One of the most important factors in the production of ASTM B670 Inconel 718 Sheet is the plate rolling process. There are two main types of Inconel 718 plates available on the market: hot rolled and cold rolled plates.

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

UNS N08367 also commonly referred to as alloy AL6XN is a low carbon, high purity, nitrogen-bearing “super-austenitic” nickel-molybdenum alloy with excellent resistance to chloride pitting and crevice corrosion.

This modification was to control carbon (.05-.10%) and grain size to optimize stress rupture properties. Incoloy 800HT has further modifications to the combined titanium and aluminum levels (.85-1.20%) to ensure optimum high temperature properties.

The pressure ratings of the material are designated by classes 150Lbs through 2500LBs. There are different types of the duplex f51 flanges such as the raised face, ring type joint and flat face flanges.

When connecting these parts, put gasket in the middle of two flanges, then tightening the flange screws, so the two will be connected together tightly.

Duplex steel UNS S31803 round bar is widely used for ferritic and austenitic duplex stainless steel bars.

ASTM A106 Seamless Pressure Pipe (also known as ASME SA106 Pipe) is commonly used in the construction of oil and gas refineries, power plants, petrochemical plants, boilers, and ships, where the pipes must transport fluids and gases with higher temperature and pressure levels .

Titanium’s thermodynamic properties do not allow it to melt in normal conditions, because it becomes more reactive at elevated temperatures and can catch fire if the oxygen molecules are present in its environment.

Although ASTM B165 UNS N04400 material has lower strength in the annealed condition, it exhibits excellent mechanical properties even at sub-zero temperatures. Monel tubes can be used up to 1000 degrees Fahrenheit. In order to improve the mechanical properties of Monel 400 welded pipe, it is possible to make finished products on it.

Alloy 718, commonly referred to as Inconel 718, is precipitation hardened to provide maximum strength and high creep stress rupture strength. Alloys can be supplied in the annealed condition to improve machinability, followed by appropriate heat treatment.

Alloy 725 (UNS N07725) is a nickel-chromium-molybdenum-niobium alloy that is highly corrosion resistant and age hardened to twice the strength of annealed alloy 625. The strength of Alloy 725 is increased by heat treatment rather than cold treatment. This also gives strength to large uneven parts that cannot be strengthened by cold work. Alloy 725 is used for hangers, landing joints and high strength fasteners in marine applications.

HASTELLOY C276 is a Nickel-chromium-molybdenum wrought alloy that is considered the most versatile corrosion resistant alloy available. This alloy is resistant to the formation of grain boundary precipitates in the weld heat-affected zone, thus making it suitable for most chemical process applications in an as welded condition. Alloy C-276 also has excellent resistance to pitting, stress-corrosion cracking and oxidizing atmospheres up to 1900¡ãF. Alloy C-276 has exceptional resistance to a wide variety of chemical environments.

ASTM A194 bolts include metals such as manganese and silicon, with additions of phosphorus, sulfur, and carbon. ASTM A194 gr 2h bolts are suitable for high pressure or high temperature service, or both. Further machining is possible by centerless grinding or cold drawing.

Low weight combined with very high strength allows the use of even thinner materials, making an exhaust system made of high-quality titanium components extremely light and resistant at the same time.

Grade UNS S31803 is termed as a duplex class due to its mixed Austenitic-ferritic microstructure. Duplex stainless steel alloys have an equal proportion of both austenite and ferrite, which is why Duplex Steel Fittings exhibit properties prominent to both classes.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

The mechanical properties of Inconel 718 fittings are very interesting, which makes it popular in various industries. For example, ASTM B366 UNS N07718 Inconel 718 fittings have high creep rupture strength at elevated temperatures up to 700 degrees Celsius.

ASTM A453 Grade 660 is a material specification for studs, bolts, nuts and other fasteners, intended for use in high temperature bolting applications. ASTM A453 Grade 660 is classified into 4 property class namely A, B, C & D, each designated with different tensile and stress rupture properties. Grade 660 fasteners are used in bolting boilers, pressure vessels, pipeline flanges and valves, intended for high temperature service. ASTM A453 grade 660 material is chemically equivalent to ASTM B638 grade 660 stainless steel alloy, also known by alloy A286 and UNS S66286, heat treated to achieve properties defined in ASTM A453 specification.

Chromium-molybdenum alloy steel has strong crack resistance under high temperature and high pressure. Chromium molybdenum is also resistant to hydrogen attack and hot sulfide corrosion cracking.

According to the flange size, wall thickness and diameters, the pressure classes vary from class 150 through class 2500. There are also different faced flanges such as the ring type joint Alloy B2 RTJ Flange, raised face flange and flat face flange.

The UNS S32760 Pipe Fittings have high tensile strength, durability, and excellent corrosion resistive property. The specifications of SA 815 WPS S32760 Elbow has criteria like size, standard, type and many more.

La aleacion K500 tiene aproximadamente tres (3) veces el limite elastico y el doble de la resistencia a la traccion de 400 en comparacion con 400. MONEL K500 se puede fortalecer aun mas mediante el trabajo en frio antes del endurecimiento por precipitacion.

304 stainless steel plate is comprised of at most 0.08% carbon. 304 stainless steel plate also includes at most 2.0% manganese and 0.75% silicon.

ASTM Specification A106 covers seamless carbon steel nominal wall pipe for high-temperature service, suitable for bending, flanging and similar forming operations. NPS 1-1/2 and under may be either hot finished or cold drawn. NPS 2 and larger shall be hot finished unless otherwise specified. Surface finish standards are outlined in the specification.

El material Monel K500 tiene excelentes propiedades mecanicas. Tienen una resistencia a la traccion minima de 140Ksi y un limite elastico minimo de 100Ksi. La aleacion tiene una dureza de 280 Rockwell y se puede estirar facilmente en un 29 %.

Type 304L is a variant of Type 304 with a low carbon content to improve weldability and reduce the risk of reduced corrosion resistance around the weld. The yield strength and tensile energy of Type 304L are also slightly reduced compared to Type 304.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.24

The added titanium, with proper heat treatment, stabilizes the susceptibility of Inconel plate flanges to intergranular corrosion. With an unwavering commitment to quality, we offer our customers a wide variety of Inconel Butt Weld Neck Raised Face Flanges.

ASTM B564 UNS N04400 Pipe Flange Monel 400 has a wonderful corrosion resistance by many reducing media such as sulfuric and hydrochloric acids.

The levels of molybdenum and copper enable Monel K500 Ring Joint Type Flanges to resist reducing agents and acids. Chromium in Monel K500 Spectacle Blind Flanges gives resistance to oxidizing conditions, such as nitric acid solutions, nitrates and oxidizing salts.

Additionally, the alloy’s properties make it an excellent choice for sea-water applications, including freedom from local attack (pitting and crevice corrosion), high corrosion-fatigue strength, high tensile strength, and resistance to chloride-ion stress-corrosion cracking.

Stainless Steel 304 Buttweld Fittings are made up of a basic austenitic stainless steel material that has 18% chromium and 8% nickel in its composition.

SAE 310 stainless steel is a highly alloyed austenitic stainless steel used for high temperature application. The high chromium and nickel content give the steel excellent oxidation resistance as well as high strength at high temperature. This grade is also very ductile, and has good weldability enabling its widespread usage in many applications
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20