GR.70N bleed ring sturdy construction

Inconel 718 is a nickel-chromium-based alloy that is commonly used in high-temperature applications such as aerospace and gas turbines. One of the most important factors in the production of ASTM B670 Inconel 718 Sheet is the plate rolling process. There are two main types of Inconel 718 plates available on the market: hot rolled and cold rolled plates.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

AL6XN is a superaustenitic stainless steel with outstanding resistance to chloride pitting, crevice corrosion and stress corrosion cracking. AL6XN is a 6 moly alloy that was developed for and is used in highly aggressive environments. It has high nickel (24%), molybdenum (6.3%), nitrogen and chromium contents that give it excellent resistance to chloride stress corrosion cracking, chloride pitting, and exceptional general corrosion resistance. AL6XN is primarily used for its improved pitting and crevice corrosion resistance in chlorides. It is a formable and weldable stainless steel.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Higher chromium, molybdenum and nitrogen content results in a Pitting Resistance Equivalent Number (PREN) > 40, providing superior pitting and crevice corrosion capabilities to austenitic and duplex stainless steels in virtually all corrosive media, and critical pitting temperature Above 50¡ãC .

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel based 800 Incoloy Hexagonal Pipe is known to have a good resistance to corrosion. Specifically speaking, the Incoloy 800 Pipe offers sufficient resistance against both carburization as well as oxidation corrosion.

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Incoloy 800H Flange We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

ASTM A240 Type 2205 Plate is a duplex stainless steel plate that is used extensively in various industries such as chemical processing, oil and gas exploration, and marine engineering. SA 240 GR 2205 Sheet is made from grade 2205 stainless steel, which is a combination of ferritic and austenitic steel.

It is widely used in offshore oil and gas exploration/production and in heat exchangers in petrochemical/chemical processing.

304 Piping Spools are made of 304 Stainless Steel, a common and popular material in many industrial applications that require resistance to corrosion and oxidation. These S30400 Piping Spools are prefabricated using specialized machinery and processes, which ensure that they are highly accurate and reliable.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

ASTM A312 TP316 is a standard specification for seamless, straight-seam welded, and heavily cold worked welded austenitic stainless steel pipes used in high-temperature and general corrosive service applications. The 316 Seamless Industrial Steel Pipe is made from a combination of chromium, nickel, and molybdenum, which gives SS 316 Seamless Tube excellent resistance to corrosion and rust.

The pipes of seamless configurations have higher load-bearing capacity and strength over other grades.

ASME B36.19M is the standard specification for stainless steel pipes, which specifies the dimensions, tolerance, and manufacturing requirements for both welded and seamless pipes.

Nickel 200 flanges The Nickel 200 Flanges are durable, dimensionally stable, and have a fine finish. Moreover, the ASTM B564 UNS N02200 Blind Flanges are resistant to corrosion in neutral and oxidizing environments, making them perfect for use in food handling equipment.

SMO 254 Pipes can withstand high mechanical stress and Alloy 254 SMO Pipe high pressure work in high temperatures and corrosive environments.

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

A789 UNS S31803 and UNS S32205 are two grades of duplex stainless steel that are widely used in various industrial applications. These Duplex S31803 Seamless Pipes are known for their excellent corrosion resistance, high strength, and good weldability. A789 is a specification that covers seamless and welded tubes made from duplex stainless steel.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

Inconel 600 round bar is a nickel-based alloy with benign carburization and excellent corrosion resistance at high temperatures. Inconel 600 round bars are effective against drying Cl2 and many other different gases at mild and high temperatures. Alloy 600 bar is a nickel-chromium alloy with good oxidation resistance and resistance to chloride pressure decomposition cracking, high cleanliness water corrosion and acid oxidation at elevated temperatures.

Alloy 800 Weld Neck Flanges We have a strong reputation in the industry for producing high-quality flanges of different types that would suit the requirements of our clients. We manufacture Incoloy 800 Flanges which are reliable and high in quality. We use premium resources and advanced machinery for producing ASTM B564 UNS N08800 Incoloy 800 Flanges.

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

Inconel 600 seamless tubes of standard UNS N06600 and ASTM B167 are the ones manufactured to sustain excessively high pressure and come with great warranty.

Titanium’s density is about 60% that of stainless steel and nickel alloys, this weight saving makes it a popular choice in applications where this is critical such as aerospace.

The 316 stainless steel pipe has become an indispensable material for the industrial sector. This alloy of iron and chrome is recognized for its high resistance to corrosion, as well as its durability. 316 stainless steel tubing can be produced in both seamless and welded tubes to meet specific customer needs.

Alloy 800 is a nickel-iron-chromium alloy with high strength and excellent resistance to oxidation and corrosion at high temperatures. ASTM B407 UNS N08800 Incoloy 800 W. Nr. 1.4876 Welded Pipe is widely used for construction of equipment requiring corrosion resistance, heat resistance, strength, and stability for service up to 1500°F (816°C).

Bending a pipe or tube using a stationary die while a counter die bends the material around the stationary die.

ASTM A479 Duplex Steel UNS S32205 Round Gaskets are nitrogen reinforced duplex alloys formed to address common corrosion problems found incidentally with 300 series alloys. ASME SA 479 Duplex Steel UNS S31803 Machined Washers are hardened at 1868 to 1958 degrees Fahrenheit and then water quenched.

A105 carbon steel is a steel with moderate carbon content. This makes it ideal for applications requiring good strength and toughness, such as pressure vessels and piping.

Incoloy 800, also known as Alloy 800 or UNS N08800, is an iron-nickel-chromium alloy with good creep & stress-rupture strength and excellent resistance to oxidation, sulfurization and carburization in high-temperature services. It also resists corrosion by many aqueous

Alloy 600 has good hot and cold workability in the annealed condition. Hot-working should be done above 1600¡ãF (871¡ãC) to ensure adequate ductility, while cold work should be performed below 1200¡ãF (649¡ãC).

Alloy 800H rods are designed to have a uniform cross-sectional area and can be produced in square, round or rectangular sizes. Versatile ASTM B408 UNS N08800 rods are rigorously tested to detect and eliminate any defects in these robust assemblies.

The Inconel 625 material used in producing the products in this grade possesses superior strength and hardness.

Monel 400 has very good mechanical properties at sub-zero temperatures, can be used up to 1000¡ãF, and has a melting point of 2370-2460¡ãF. However, Alloy 400 has low strength in the annealed condition, so various tempers can be used to increase the strength.

SA182 F1 forged flanges are used as connecting parts to create piping networks for cylinders, valves, pumps and other equipment. Combine two different parts of the machine. To make the structure stronger, it should be an attachment to the frame.

Super Duplex UNS S32760 /F55 Flanges are made up of the super duplex grade of stainless steel. The material has 24% chromium, 6% nickel, 3% molybdenum, copper, tungsten, carbon, nitrogen, manganese, silicon, phosphorus, iron and sulfur. The ASTM A182 F55 Flange has high strength and high corrosion resistance. The flanges are made under ANSI Ba6.5, ANSI B16.47 and other international standards.

ASTM B564 UNS N04400 Slip on Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Valued for its high strength and corrosion-resistant properties, Monel 400 is available from Continental Steel in multiple forms for use in a variety of end uses.

ASTM A182 F304 Flanges
?The?ASTM A182 F304 Flanges?could be cleaned easily with a mild detergent. Despite undergoing repeated cleaning processes, these flanges won¡¯t wear away, an ability it exhibits due it its good wear resistance properties. Moreover, since grade 304 is an alloy that can be easily formed into various shapes, it is easily manufactured into any type of?ASME SA182 F304 Pipe Flange?such as a weld neck flange or an?Inox 304 Slip On Flange.

ASTM A193 Grade B7 is the standard material specification for chromium-molybdenum alloy steel fasteners for high-strength, high-temperature, and special-purpose applications. Grade B7 is a heat treated chromium molybdenum alloy steel with a minimum tensile requirement of 100 ksi, a yield strength of 75 ksi and a maximum hardness of 35 HRC. The ASTM A193 specification covers requirements for chemical composition, mechanical properties, hardness, heat treatment, and recommended nut washers for Class B7 fasteners. ASTM A193 Grade B7 is the broadest specification for fasteners, commonly found in bolts or pipes, pressure vessels, valves, flanges and fittings.

316L stainless steel possesses less carbon and molybdenum than typical 316 steel, which gives the two alloys different characteristics.

The size of these forgings range from ? NB to 250 NB and length of these forgings is 2mm to 40mm.

In addition to high ductility, the material shares several other characteristics with nickel. For example, ASTM B164 Monel 400 round bar is well suited to work in moderately reducing applications because nickel works very well in reducing environments.

The ASME SA 234 Gr WPB Pipe Elbow and other fittings can come in different dimensions according to the ASME/ ANSI B16.9 and B16.28 standards.Common use material are ASTM A234 Grade WPB, WPC, WP5, WP9, WP11, WP22 and WP91. It covers the butt-welded pipe fittings of Elbow, Tee, Reducer, Cap and Cross, and some socket welding, threaded pipe fittings.

HT PIPE provides high quality ASTM A350 LF3 Grade 1 and 2 Plate Flanges, we manufacture SA350 LF3 Pipe Flanges, LF3 Carbon Steel Flanges and ASTM A350 Gr LF3 Cl1 Blind Flanges at low prices in China.

ASTM A182 Grade F5 Flanges are suitable for connecting pipes of small bore size and without the requirement of welding. ASTM A182 GR F5 Flange belongs to the ASTM A182 specification. The dimensions of the flanges vary according to the ANSI, ASME and DIN standards. The flange sizes range from ? inches to 36 inches in nominal bore sizes. Navstar Steel is a leading supplier and manufacturer of these flanges in various sizes and types.

In the manufacturing industry, the production is done by obviously using the best possible quality of crude materials and alloys. It thus tends to offer various good attributes.

Alloy 400 is highly regarded as one of the best performing engineering alloys.

Alloy steel is steel that is alloyed with a variety of elements in total amounts between 1.0% and 50% by weight to improve its mechanical properties. Alloy steels are broken down into two groups: low alloy steels and high alloy steels. The difference between the two is disputed. Smith and Hashemi define the difference at 4.0%, while Degarmo, et al., define it at 8.0%.[1][2] Most commonly, the phrase “alloy steel” refers to low-alloy steels.

Alloy C276 bar welding products are used as a matching composition filler material for welding C276 alloy forged and cast products in dissimilar welding applications including other NiCrMo alloys and stainless steels, as well as for surfacing or cladding of steel. Parts thermoformed in HASTELLOY C-276 alloy bar should, if possible, be solution heat treated prior to final fabrication or installation.

ASTM A182 Alloy Steel Pipe Fittings are very easy to install and have a low hub due to the pipe going into the fitting before welding.

N08825 Slip-On Flange Incoloy 825 Flanges (UNS N08825) is composed of addition of molybdenum, copper, and titanium into its nickel-iron-chromium base. The extra metals give Incoloy 825 Blind Flange exceptional resistance against corrosion, even more so than other nickel alloys.

This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength.

We are manufacturers, suppliers and exporters of Carbon Steel A105 / A105N Flanges, which, the American Society for testing materials, classifies as a standard that covers forged Carbon-Steel piping parts that also include carbon steel pipe flanges, which are serviceable in pressure systems at room temperatures as well as temperatures higher than it. We produce Carbon Steel A105 / A105N Blind Flanges which are successful in pressure bearing and sealing pipe ends in heavy pressure applications like hydraulic systems since they have a maximum bending stress at the centre.

The SS 904L coil is used in heat exchangers and in high temperature applications because of their high melting range of 1300 to 1390 degrees Celsius.

Alloy 925 / Incoloy 925 / UNS N09925 is an age-hardenable nickel-iron-chromium alloy with additions of molybdenum, copper, titanium and aluminum. Each of these additions plays their part in making Alloy 925 a high strength alloy with excellent corrosion resistance. Alloy 925 is used in a variety of applications in the crude oil and natural gas industries because of its resistance to sulfide stress cracking and stress corrosion cracking, making it the perfect alloy for downhole and surface gas well components.