Hastelloy C276 butt welded elbows has high corrosion resistance in many chemical environments

Hastelloy C2000 Tubes are used in a broad range of industries including petrochemical processing, chemical processing equipment manufacturing, oil refineries and power plants.

It is able to withstand a wide range of oxidizing and non-oxidizing chemicals, and exhibits outstanding resistance to pitting and crevice attack in the presence of chlorides and other halides.

This provides greatly enhanced resistance to sulfuric acid. It also has a high chromium content, to maximize its resistance to oxidizing chemicals and process streams contaminated with ferric ions and dissolved oxygen.

It demonstrates good resistance to neutral and reducing environments. This alloy creates a tenacious oxide, protective film that does not spall off, but it retains superior oxidation resistance at soaring temperatures.

Hastelloy C2000 is available in a variety of sizes and thicknesses, this type of nickel-chromium-molybdenum alloy is renowned for its superior strength and corrosion resistance.

Hastelloy Alloys Directory
The Corrosion Resistant HASTELLOY alloys are widely used by the chemical processing industries. The need for reliable performance leads to their acceptance and growth in the areas of energy, health and environmental, oil and gas, pharmaceutical and flue gas desulfurization industries.

Alloy B Its popularity has been hindered by its availability. All of these materials are good against reducing acids, but very hard against oxidizing acids. Due to the high molybdenum content, this alloy is relatively expensive than other alloys. At the same time, it has excellent corrosion resistance to medium-concentrated sulfuric acid and various non-oxidizing acids, good resistance to chloride stress corrosion cracking (SCC), and good resistance to various organic acids.

Superalloys have good oxidation and creep resistance and can be strengthened by methods such as precipitation hardening, solution hardening and work hardening. They can also function under high mechanical stress and high temperature and where high surface stability is required.

HASTELLOY C276 is a Nickel-chromium-molybdenum wrought alloy that is considered the most versatile corrosion resistant alloy available. This alloy is resistant to the formation of grain boundary precipitates in the weld heat-affected zone, thus making it suitable for most chemical process applications in an as welded condition. Alloy C-276 also has excellent resistance to pitting, stress-corrosion cracking and oxidizing atmospheres up to 1900¡ãF. Alloy C-276 has exceptional resistance to a wide variety of chemical environments.

Hastelloy is a corrosion-resistant nickel alloy that contains other chemical elements such as chromium and molybdenum. This material has high temperature resistance and exceptional corrosion resistance. Hastelloy C276 is one of the grades of Hastelloy used in the oil and gas industry.Hastelloy nickel alloys are fully resistant to a vast array of chemicals, including highly acidic hydrochloric and sulfuric acids. It is also one of the few materials available that can withstand wet chlorine gas, chlorine dioxide and hypochlorite.

This action draws the pipe or tube forward making the desired bend.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

These flanges are usually welded or screwed. In those instances where welding or bolting the flange is not possible, many industries prefer using WNR 2.4602 Threaded Flanges.

C276 is forged between 2250/1750oF (1230/955oC) and then soaked at the forging temperature for 30 minutes per inch of billet or ingot section thickness. Forging should begin immediately, the billet is removed from the reheat furnace, a 25/40% reduction helps retain as much internal heat as possible. For optimum corrosion resistance, forged parts should be subsequently annealed. See Heat Treatment.

Hastelloy C-276 alloy can be forged, hot-upset, and impact extruded. Although the alloy tends to work-harden, it can be successfully deep-drawn, spun, press formed or punched.

Hastelloy Nickel Alloy B2 is a very chemically resistant alloy with high resistance to pitting and stress corrosion cracking in the heat affected zone. In particular, this alloy performs well in harsh environments such as sulfuric acid, hydrogen chloride and phosphoric acid. This nickel-molybdenum alloy is typically used under extreme reducing conditions and has a much lower composition of carbon, silicon and iron than Hastelloy B (Alloy B). Screws made from this alloy are also known as UNS N10665 fasteners.

The outstanding oxidation resistance of HASTELLOY X pipe bend is illustrated below. Tests were conducted by exposing samples to dry air at 2000 Deg. F. and to dry air pressurized to 300 psi at 1750 Deg. F.

Nickel Alloy C-276 and Hastelloy C-276 can be welded by all common welding methods (oxyacetylene is not recommended).

These flanges exhibit superior resistance to carburization and chloride stress corrosion cracking in reducing atmospheres.

Hastelloy C276 thin wall tubing is commonly used in marine, aerospace, chemical processing, nuclear reactors, pollution control equipment, and more.

Industry users like the resistance to a wide range of organic acids and the resistance to chloride-induced stress-corrosion cracking.

Hastelloy C-276 has a higher molybdenum content.

Hastelloy B2 is a nickel base wrought alloy with excellent resistance to hydrochloric acid at all concentrations and temperatures.

Hastelloy C276 bushings have high nickel and molybdenum contents to provide good corrosion resistance in reducing environments.

Inconel Alloy X750 Flanges, which has excellent resistance to chloride ion stress-corrosion cracking. Inconel X750 Slip On Raised Flanges is used for wire formulation with heat temper used in springs at elevated temperatures

Hastelloy X Nippo Flange is additionally being offered in customized sizes and shapes to our customers. Hastelloy X Socket Weld Flange is extremely ductile, exhibits excellent weldability, and is definitely fabricated into industrial components. Hastelloy X Ring Joint Type Flange is a fully austenitic advanced corrosion-resistant alloy that gives resistance to both aqueous corrosion and attack at elevated temperatures. Hastelloy X Flanges has greater thermal stability than Hastelloy B-2 Flanges.

Hastelloy B3 has excellent resistance to hydrochloric acid at all concentrations and temperatures. In addition, it greatly improves structural stability compared to previous B-type alloys, reducing concerns during welding, fabrication and service.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.

Our Hastelloy B2 Ring Joint Type Flanges is not recommended for use in the presence of ferric or cupric salts as these salts may cause rapid corrosion failure. Ferric or cupric salts of these Hastelloy B2 Nippo Flanges may perhaps develop when hydrochloric acid comes in contact with iron or copper.

The high molybdenum content of Hastelloy?* C276 provides the alloy with its excellent resistance to pitting and crevice corrosion.

Hastelloy C-276 is a nickel-chromium-molybdenum alloy that is resistant to corrosion.C276 alloy is suitable for many chemical process applications.

The flange is second most used joining method after welding. Flanges are used when joints need dismantling. It provides flexbility for maintenance. Flange connects the pipe with various equiment and valves. Breakup flanges are adde din the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrelated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls ae required in the selection and application of all these elements to attain a joint, which has acceotable leak tightness.

C-276 alloy has excellent resistance to pitting and to stress-corrosion cracking. It is also one of the few materials that withstands the corrosive effects of wet chlorine gas, hypochlorite, and chlorine dioxide.

The flange is second most used joining method after selding. Flanges are used when joints need dismantling. It provides flexibility for maintenance. Flange connects the pipe with various equipment and valves. Breakup flanges are added in the pipeline system if regular maintenance in required during plant operation.
A flanged joint is composed of three separate and independent although interrdlated components; the flanges, the gaskets, and the bolting; which are assembled by yet another influence, the fitter. Special controls are required in the selection and application of all there elements to attain a joint, which has acceptable leak tightness.
A flange is a protruded ridge, lip or rim, either external or internal, that serves to increase strength (as the flange of an iron beam such as an I-beam or a T-beam); for easy attachment/transfer of contact force with another object (as the flange on the end of a pipe, steam cylinder, etc., or on the lens mount of a camera); or for stabilizing and guiding the movements of a machine or its parts (as the inside flange of a rail car or tram wheel, which keep the wheels from running off the rails). The term “flange” is also used for a kind of tool used to form flanges.