high quality competitive price austenitic stainless steel tee ASTM A403 tee

ASTM A403 WP304H has a high carbon content in chemical compositions.ASTM A403 WP304H normally is used for the pressure piping systems of moderate and high temperature services. WP304H is a kind of heat and corrosion resistant steel.It has a good pipe bending,welding performance,heat and corrosion resistance,high rupture strength and stability,also the cold deformation ability is very good.It could be used up to 650¡ãC,oxidation temperature up to 850¡ãC.

Monel k500 has good corrosion resistance and long-term organizational stability.

904L (N08904, 14539) super austenitic stainless steel contains 14.0-18.0% chromium, 24.0-26.0% nickel, 4.5% molybdenum. 904L super austenitic stainless steel is a low-carbon, high-nickel, molybdenum austenitic stainless acid-resistant steel, which is a proprietary material imported from French H¡¤S Company. It has good activation-passivation transformation ability, excellent corrosion resistance, good corrosion resistance in non-oxidizing acids such as sulfuric acid, acetic acid, formic acid, phosphoric acid, and good corrosion resistance in neutral chloride-containing media Excellent pitting corrosion resistance, as well as good crevice corrosion resistance and stress corrosion resistance. It is suitable for various concentrations of sulfuric acid below 70 ¡ãC, and has good corrosion resistance in acetic acid of any concentration and temperature under normal pressure, as well as in the mixed acid of formic acid and acetic acid.

It is extensively used in heavy gauge welded components (over about 6mm). There is commonly no appreciable price difference between 316 and 316L stainless steel.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

We also produce Carbon Steel ASTM A234 WPB Threaded elbows with all male connections, all female or a combination of each.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Duplex stainless steel pipes and fittings are generally less expensive because of the lower proportions of alloying elements used in the manufacture of duplex stainless steels. The yield strength of duplex stainless steel products is higher than that of austenitic stainless steel products, so users can buy duplex pipes and duplex pipe fittings with relatively lower thickness.

Monelk500, also known as UNS N05500, has the same corrosion resistance as monel400, but has higher mechanical strength and hardness. It has good corrosion resistance and long-term organizational stability.

A pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction
or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

S31803 is the Unified Numbering System (UNS) designation for the original duplex stainless steel. The UNS system was created by multiple trade groups in the 1970s to reduce confusion when the same alloy was called different things, and vice versa. Each metal is represented by a letter followed by five numbers, where the letter represents the metal series, i.e. S for stainless steel.

For paper mill applications requiring lower alloy grades that do not have sufficient corrosion resistance. Based on a 22% chromium content, they have a combined austenitic:ferritic microstructure that provides greater strength, corrosion resistance and cost-effectiveness.

The UNS S31803 (ASTM F51) specification has been largely superseded by UNS S32205 (1.4462, ASTM F60). This reflects their desire to maximize the alloy’s corrosion properties, thanks to the development of the AOD steelmaking process, which allows for tighter control of composition. In addition, it allows to influence the nitrogen addition level rather than just being present as a background element. Therefore, the highest performing duplex grades seek to maximize the content of chromium (Cr), molybdenum (Mo) and nitrogen (N).

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

INCOLOY Alloy 800 (UNS N08800/W. Nr. 1.4876) is a widely used material for the manufacture of equipment requiring corrosion resistance, heat resistance, strength and stability, operating temperatures up to 1500¡ãF (816¡ãC) ).

AISI 04 stainless steel and 304L stainless steel are general purpose stainless steels with good resistance to atmospheric corrosion, many organic and inorganic chemicals, and food and beverages. The difference between 304 and 304L stainless steel is that 304L has a maximum carbon content of 0.03, which is suitable for welding, while 304 has a moderate carbon content.

The Incoloy 825 consists of small amounts of copper, titanium, and molybdenum, contributing to its excellent mechanical properties. The Incoloy 825 Pipe Fittings have high resistance to pitting and crevice corrosion.

The manufacturing process of A860 WPHY 52 includes heat treatment.

Generally, the corrosion resistance of Monel K500 in solid solution is basically the same as that of Monel 400 alloy, so the corrosion resistance data of Monel 400 can be applied to Monel K500 alloy. Due to its low corrosion rate and high strength in flowing seawater, the alloy is particularly suitable for manufacturing seawater corrosion-resistant centrifugal pump shafts.

Stainless Steel 316 is the standard molybdenum-bearing grade, second in importance to SS 304 amongst the austenitic stainless steels.

WPHY 52 chemical composition are known for accurate dimension, corrosion resistance and their durability.

All SA234 WPB Elbow are manufactured in India and produced from strictly European sourced raw material. All ASTM A234 Elbow & Elbow A234 Wpc are manufactured from plate, pressed in two halves with two weld seams.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

MONEL K500 is non-magnetic. MONEL K500 should be annealed when welded and the weldment then stress relieved before aging.

Stainless Steel 316H Stub End Pipe Fittings are equivalent to those of the parent metal, matching or slightly over-alloyed fillers should preferably be used.

They are generally used to attach (or join) two or more pipes (or tubes) together using pipe fittings. They help to make the joint stronger by adding additional strength to the joint, thereby helping to maintain the position of joint with increased stability. Pipe Fittings helps to change the direction of pipe/tube and ensures smooth flow of the content within. Pipe Fittings are also known as Buttweld Fittings.

A butt weld pipe fitting is designed to be welded on site at its end(s) to connect pipe(s) together and allow change in direction or pipe diameter, or branching or ending.

This fitting then becomes part of a system for transporting fluids (oil, gas, steam, chemicals, …) in a safe and efficient manner, over short or long distances.

ASTM A234 WPB Fittings are made up of different material grades.Hot formed WPB, WPC, WPR fittings forming at above 620¡æ[1150¨H] to 980¡æ[1800¨H] no need to be heat treated which they are cooled in still air.

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with good mechanical properties from sub-zero temperatures up to about 550 ¡ãC (1020 ¡ãF) and is approved for pressure vessels with wall temperatures from -10 to 425 ¡ãC (14 to 800 ¡ãF) according to VdTUV-Wbl. 263 and up to 900 ¡ãF (480 ¡ãC) according to ASME Boiler and Pressure Vessel Code.

The austenitic structure of 316 stainless steel provides excellent toughness even at low temperatures.