HT ASTM B366 WPNIC N08800-S 1.5 SCH10S 90 DEGREE 3D ASME B16.9 Heat No.48431

Nilo / Alloy K W.Nr.: 1.3981
UNS: K94610 ASTM F15
Fixed-expansion glass-encapsulated iron-nickel-cobalt alloys, Kovar alloys, have a linear thermal expansion coefficient similar to that of hard glass within a certain temperature range
For mating sealing with hard glass

Nilo Alloy 36, W.Nr 1.3912, Invar 36® is a nickel-iron, low controlled expansion alloy that contains 36% nickel and possesses a rate of thermal expansion approximately one-tenth that of carbon steel.
Invar 36 Specifications: UNS K93600, W.Nr 1.3912

Common Trade Names: Nickel Alloy 36, Invar 36®, Nilo 6®, Pernifer 6®
Invar 36® is a nickel-iron, low expansion alloy that contains 36% nickel, Invar 36 has a low coefficient of expansion from cryogenic temperatures to about +500°F (260°C).
Invar 36 Tube OD:0.2-6mm, WT: 0.02-2mm

ASTM A182 GR F5 flanges fall under the ASTM A182 specification.

SA 182 Gr F1 Slip on Flanges also known as SO flanges. This is a flange that slides over the pipe and has an internal design that is slightly larger than the pipe.

The Alloy Steel Blind Flanges are used to close a pipe connection. There are different types and grades of the blind flanges as well.

Alloy Steel F12 slip on Flanges are made up of chromium molybdenum steel alloy and therefore have a high rupture resistance. They are also preferred due to their light weight because of the low carbon and high alloy nature.Alloy Steel ASTM A182 flanges are very simple to install and have a low center because the pipe occasionally trips into the flanges after welding.

ASTM A182 F9 Flanges also have higher corrosion resistance levels. Alloy Steel F9 Threaded Flanges can be susceptible to sensitisation, the formation of grain boundary chromium carbides at temperatures between approximately 900 and 1500 Degree F (425 to 815 Degree C) which can result in intergranular corrosion.

Hot rolled 4140 steel bar is a medium carbon alloy steel with high hardenability. This grade is also widely used in forging.

We offer a wide range of ASTM A335 P9 alloy steel seamless pipes using high quality raw materials. These alloy steel P9 ERW tubes are forged between 2250¡ãF/1750¡ãF (1230¡ãC/955¡ãC) for 30 minutes per inch of billet or ingot section thickness. These are A335 P9 pipes manufactured to international quality standards. These alloy steel P9 seamless pipes are also available in different sizes, grades, thicknesses and specifications according to customer requirements.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P141

Impact strength as well as high surface smoothness are the result of round bar forging of alloy steel DIN 1.7335. Once the materials are forged, they are allowed to cool to the temperature specified by the specification ASTM A 182.

Alloy 20 (Alloy 20) is an iron-based austenitic alloy developed to resist sulfuric acid corrosion. It has excellent resistance to sulfuric acid corrosion; it has strong resistance to phosphoric acid, nitric acid and chloride environments, chloride stress corrosion, pitting corrosion and crack corrosion. Therefore, alloy 20 has the name of anti-corrosion alloy; it has a wide range of applications: such as: chemical, food, medicine, power production and plastics industries will use it. For resistance to pitting corrosion and chloride corrosion, stress corrosion cracking problems, etc., alloy 20 is often used.

Ferritic alloy steel pipes are considered to have high chromium concentration and low carbon percentage. These magnetic alloy steel pipes have key qualities including high ductility, corrosion resistance and resistance to stress-related corrosion cracking. Therefore, IBR-certified alloy steel pipes are commonly used in automotive, kitchen and industrial equipment applications.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.63

The A335 P91 chrome tube composition makes these high mechanical properties possible for the material. P91 steel pipe materials can be normalized and tempered during the production process, and can also be quenched and tempered. These methods increase the strength of the material. Additionally, these pipes are drawn and seamless.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.24

Chromium Molybdenum Alloy Steel or Chromium Molybdenum, CrMo is an alloy steel used for high temperature and high pressure service. Chromium molybdenum is used in power generation and petrochemical industries for its tensile strength, corrosion resistance and high temperature strength. Chromium molybdenum has a better strength-to-weight ratio than steel, which enables designers to use thinner walled tubing or smaller diameter tubing to reduce overall weight.

ASTM A182 F12 flat bar is a flat rectangular section with square edges of varying sizes. It is suitable for a variety of applications, distributed in engineering, construction, manufacturing, manufacturing, mining, light grids and many other industries.

The ease and economy with which INCONEL alloy 718
can be fabricated, combined with good tensile, fatigue,
creep, and rupture strength, have resulted in its use in a
wide range of applications.

Alloy steel is a steel alloyed by adding a variety of elements with a total amount between 1.0% and 50% in order to improve its mechanical properties. Alloy steels are divided into two categories: low alloy steels and high alloy steels. The distinction between the two is debatable. Smith and Hashemi defined the difference as 4.0%, while Degarmo et al. defined the difference as 8.0%. Most commonly, the phrase “alloy steel” refers to low alloy steel.

Our Alloy Steel ASTM A182 F5 Weld-neck Flanges are supplied to aid industrial, high pressure services like condensers, boilers, evaporators, heat exchangers, etc. Alloy steel F5 A182 flanges is also available in the form of lap joint flanges, plate flanges, threaded flanges, reducing flanges and many more. These flanges are widely used in power generation industry, gas processing industry, pharmaceutical industry, heat exchangers industry, sea water equipment industry, oil drilling companies and many more.

The a182 f9 flange is considered a cost saving option. In addition to these properties, astm a182 f9 is reusable and corrosion free.

El grado B7 es un acero de baja aleacion de cromo molibdeno tratado termicamente con un requisito minimo de resistencia a la traccion de 125 ksi (860 Mpa), un limite elastico de 105 ksi (720 Mpa) y una dureza maxima de 35HRC. Boltport produce pernos con cabeza y sin cabeza B7 a partir de barras de acero aleado AISI 4140 o piezas forjadas.

Which means that one has to know if the alloy steel flange material is critical to achieving good weld integrity and the need for proper filler metal selection.High heat resistance steel grades are generally known as Chromium Molybdenum Steel.

At elevated temperatures, conventional steels, unlike ASTM A 335 P91 pipes, begin to lose their microstructural form, leading to failure. A burst or crack in the pipe is a visible fault. But since SA 335 P91 chrome-plated welded pipe is well suited to sustain itself at high temperatures, failure rates are extremely low.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

ASTM A182 F9 alloy steel round bars can be customized according to customer requirements. They are widely used in automotive and other fields due to their excellent quality and unparalleled functionality.

A335 P22 Chromium Pipe contains chromium in its composition to provide high corrosion resistance. There are other elements in the material composition of P22 steel pipe. Molybdenum is a common addition in all A335 grades. Manganese, phosphorus, silicon and carbon are added according to different grades.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.43

A335 p9 pipes are made of ferritic alloy steel for high temperature applications. The sa335 p9 material chemically contains metals such as molybdenum and chromium added to the alloy. By adding metals such as molybdenum and chromium, the tensile strength of the alloy is increased. The yield strength of the a335 p9 welded pipe is 205 Mpa, while its tensile strength is 415 Mpa. The elongation of the pipe is about 30%.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.19
Material Alloy Steel ASTM A333 Grade 3, Grade 6,Grade 8,Grade 9
ASTM A335 P5,P9,P11,P12,P22,P91,P151

ASTM A194 Class 2h bolts are carbon base steel heavy duty hex nuts. Sa194-2h material is a common high strength nut. This specification ASTM A194 Class 2h washers are typically used in conjunction with the following fastener standards – A193 Class B7, A325, A490.

The product portfolio is designed to be durable plumbing components, a sustainable alternative with premium quality that aids business growth.

The ASTM A194 specification covers carbon, alloy and stainless steel bolts for high pressure and/or high temperature service.

It must be slid into the pipe before welding. In this case, it’s a double weld on both sides (i.e. inside and outside), so it provides durability that helps avoid leaks.

After hot working, forgings should be cooled to a temperature below 1000¡ãF (538¡ãC) prior to heat treatment in accordance with ASTM A182. Low alloy steels and ferritic and martensitic stainless steels shall be heat treated in accordance with ASTM A182.

Our alloy steel blind flanges are mainly caused by environmental factors such as wind exposure, man-made pollution and high temperature, and are more serious near the ocean, which is the main cause of seawater pollution.

Chrome moly alloy flanges connect pipes, valves, pumps and other equipment, forming a piping system.