Manufacturing Standard of Monel 400 Flanges ASME B16.48 Flanges

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

It has good mechanical properties from subzero temperatures up to about 480C.

Monel 400 (UNS N04400) is a nickel-copper alloy with optimum high strength and corrosion resistance. It is widely used in a variety of severe acidic and alkaline environments. Monel is also used in pipes.

Studs are threaded at both ends and the middle screw, either thick or thin.It is generally used in mining machinery, Bridges, automobiles, motorcycles, boiler steel structure, pylon, long-span steel structure and large buildings. A bolt is a screw with a larger diameter or without a head, such as a stud.

This nickel alloy is attacked in sulfur-bearing gases above approximately 700¡ã F and molten sulfur attacks the alloy at temperatures over approximately 500¡ã F.

Essentially, Monel 500 is an age-hardened version of Monel 400. This means that Monel 500 is harder and more resistant to corrosion than Monel 400. This material can be used in sour gas applications. Monel K500 Studs maintain corrosion resistance even in high velocity seawater. Hence, these applications are in seawater and marine engineering applications as well as in shipbuilding applications.

It is suitable for temperatures up to 1000¡ãF (538¡ãC). Alloy 400 has excellent resistance to cavitation and erosion in fast-flowing brackish or seawater.

We manufacture Monel K500 flanges from nickel and copper alloys. The material has excellent resistance to aggressive materials and solutions such as oxidizing salts, acids, nitrates and other oxidizing agents.

Monel 400 is widely used in Feed water and steam generator tubing.

The composition of Monel K500 fasteners includes carbon, 2.3% aluminum, manganese, silicon, iron, sulfur and titanium in addition to nickel and copper. It is this unique composition that gives the material its superior strength, extreme corrosion resistance and ductility. Applications for these fasteners include the offshore petroleum industry, power plant applications, petrochemicals, gas handling units, specialty chemicals, and more.

Alloy K500 is refined by Electroslag Refining (ESR), ensuring the cleanest and highest quality material. This increased alloy purity limits the potential for hard non-metallic inclusions that can increase machining difficulty, machining time and ultimately lead to part failure. It also has low permeability and is non-magnetic at temperatures as low as -150¡ãF (-101¡ãC).

If hardened Monel 400 is the goal, cold working with a soft tooling material is the only option. By cold working, mechanical stress is used instead of heat to change the shape of the metal.

Unique among Monel alloys, ASTM B165 Monel Seamless and Welded Pipe is considered a Puritan alloy because it contains the same nickel and copper content as the natural nickel ore found in the Sudbury mine in Ontario, Canada.

Monel K500 is a Nickel-Copper alloy that is precipitation hardenable, due to the additions of Aluminium and Titanium.

Typical applications are valves and pumps; pump and propeller shafts; marine fixtures and fasteners.

MONEL K-500 alloy has corrosion resistance comparable to 400, but has higher mechanical strength and hardness. Has good thermal corrosion resistance and long-term tissue stability. It is mainly used in the manufacture of turbine blades and gas turbine blades with a working temperature below 750¡ãC on aero-engines, and in the manufacture of fasteners and springs on ships; pumps and valve parts on chemical equipment, and scraping on paper-making equipment. Blades etc.

Monel K500 Fasteners are precipitation hardenable nickel and copper base alloy fasteners. These fasteners are developed for the excellent corrosion resistance adding with benefits of great hardness and strength.

A finished hex nut, also known as a standard hex nut, has a smaller width across the flats and corners compared to a heavy hex nut. Heavy hex nuts are thicker and heavier in weight. The proof load strength is higher than a standard hex nut. Heavy hex nuts provide increased bearing surface area over finished nuts.

Monel 400 Seamless Tubing, Monel 400 Tubing, Alloy 400 Gas Tube, Monel 400 boiler tubes & Monel 400 Polish Tube are most often found in chemical plant equipment due to their strong resistance to chemical corrosion.

Typical application for MONEL K500 which takes advantage of high strength and corrosion resistance are pump shafts, impellers, propeller shafts, valve components for ships and offshore drilling towers, bolting, oil well drill collars and instrumentation components for oil and gas production. It is particularly well suited for centrifugal pumps in the marine industry because of its high strength and low corrosion rates in high-velocity seawater.

Monel K500 bolts and nuts are used in a variety of industries due to their high temperature resistance, high corrosion resistance and durability. It is a nickel-copper alloy with a composition of 63% nickel and 27% copper, among other elements.

Monel K500 fasteners have trusted properties such as strength, hardness and fracture toughness, which are achieved through the addition of aluminum and titanium as well as nickel and copper alloys. Its basic composition is similar to ALLOY400, but alloys are added to allow age hardening under controlled temperature and time conditions.

Monel 400 is an alloy of nickel and copper, typically formulated at about 67% nickel and 33% copper.

Monel nuts are often used for standard and advanced applications where high levels of strength and superior corrosion resistance is nearly always required. Monel 500¡¯s premium corrosion resistance, strength and usability in extreme conditions makes it the ideal choice for a wide range of industrial applications.

The Curie temperature of this alloy lies within the ambient temperature range and is affected by changes in the alloy’s chemical composition. Caution is recommended in applications requiring strong non-magnetic properties.

The levels of molybdenum and copper enable Monel K500 Ring Joint Type Flanges to resist reducing agents and acids. Our wide array of UNS N05500 | Monel K500 Threaded Flanges is utilize in rough oil stills, gas and new water tanks, marine installations and clasp, and concoction preparing gear.

MONEL K500 conserva las excelentes propiedades de resistencia a la corrosion de 400, con mayor resistencia y dureza despues del endurecimiento por precipitacion en comparacion con 400.

Monel K500 steel bars are particularly suitable for centrifugal pumps in the marine industry. This is due to the properties of Monel N05500 hot rolled bar, namely high tensile strength and low corrosion rate in high velocity seawater.

In fact, in comparison to nickel, the corrosion resistance properties of UNS N04400 Orifice Flange tend to be much higher than nickel itself.

Monel K-500 (N05500) Bolts are manufactured by the cold heading and hot forming technologies in nominal diameters ranging from 1/8¡±- 3¡± (M3 ¨C M80). It can be in both USCS/Imperial and metric sizes.

ASTM B564 UNS N04400 Pipe Flange Monel 400 has a wonderful corrosion resistance by many reducing media such as sulfuric and hydrochloric acids.