Monel 400 2.4360 nickel alloy pipe prefabrication resistant to sea water

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Alloy 400 is resistance to neutral, alkaline and acid salts is shown, but poor resistance is found with oxidizing acid salts such as ferric chloride.

We manufacture Monel K500 flanges from nickel and copper alloys. The material has excellent resistance to aggressive materials and solutions such as oxidizing salts, acids, nitrates and other oxidizing agents.

Alloy 400 is a solid solution alloy that can only be hardened by cold working.

Monel 400 has very good mechanical properties at sub-zero temperatures, can be used up to 1000¡ãF, and has a melting point of 2370-2460¡ãF. However, Alloy 400 has low strength in the annealed condition, so various tempers can be used to increase the strength.

Monel nickel copper k500 hex bolts are often used for standard and advanced applications where a combination of strength and corrosion resistance is a necessity. Monel UNS N05500¡¯s advanced quality corrosion resistance and usability in extreme conditions makes it the perfect choice for a wide range of industrial applications. Some of which, include:

Chemical processing equipment
Marine applications
Petroleum tills & gasoline tanks
Heat exchangers
Valves & pumps
Propeller shafts
Process vessels
And more

This alloy is most commonly used in a range of environments from mildly oxidizing to neutral and moderately reducing conditions. Other areas of application for this material are marine environments and other non-oxidizing chloride solutions.

Monel400 is a single-phase solid solution Ni-Cu corrosion-resistant alloy.

Adding a small amount of Mg to Monel K-500 alloy can increase the grain boundary bonding force and improve high temperature plasticity.

Alloy 400 (UNS N04400) is a nickel-copper alloy with high strength (comparable to structural steel) and toughness.

We are a maker, broker, stockist, provider and exporter of ASME SB564 Monel K500 Flanges which are precipitation solidified, high in quality ribs, yielding a rigidity of 115 ksi for a power pressed execution. Monel K500 fasteners and flanges offer a unique combination of high strength with similar corrosion resistance to Monel 400 and improved resistance to a sour-gas environments.

Monel 400 has excellent corrosion resistance in hydrofluoric acid and fluorine gas medium.

ASME SB564 Monel UNS N04400 Weld Neck Flanges are utilised in pharmaceutical equipment, heat exchangers, condensers, power generation, etc. ANSI B 16.47 Monel DIN 2.4375 Threaded Flanges are welded to a pipe or fitting with a single full penetration. HT PIPE takes ultimate pride in offering the above mentioned range of products that fall under the Monel Flanges product type that come in two grades, 400 and K500. Also We offer wide range of Monel ASTM B564 400 Flanges such as Monel 400 Slip On Flanges, Monel K500 Weld Neck Flanges.

ASTM B564 UNS N04400 Pipe Flang Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

This alloy is more resistant to nickel under reducing conditions and more resistant than copper under oxidizing conditions, it does show however better resistance to reducing media than oxidizing.

Monel K500 pipe bend and elbow are usually used in propeller, pump shafts, pumps, valves used in the manufacture of perchlorethylene, and chlorinated plastics.

Monel K500 Bolts, also known as Alloy K500, are composed of a nickel alloy that combines the excellent corrosion resistance of Monel 400 with increased strength and hardness. These additional properties of Monel K500 bolts are the result of an age hardening process in which aluminum and titanium are added to a nickel-copper matrix, which is then precipitated throughout. Compared to 400, this process increases the yield strength of K500 by a factor of approximately 3 (110ksi vs. 45ksi) and doubles the tensile strength (160ksi vs. 83ksi). Monel K500 bolts will maintain their strength down to 1200¡ãF and even maintain their ductility down to -400¡ãF.

Monel 400 flanges are a nickel-copper alloy (approximately 67% Ni ¨C 23% Cu) resistant to seawater and steam at high temperatures, as well as salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold work. This nickel alloy has good corrosion resistance, good weldability and high strength.

It has a higher melting point around 2400 degrees Fahrenheit to 2460 degrees Fahrenheit. Primarily Monel K500 grade is a spark resistant alloy. This becomes non-magnetic below -200 degrees Fahrenheit. In terms of cold working operations, magnetic structures can be achieved. The Monel nickel-copper composition of Monel 500 is highly resistant to corrosion, making it ideal for many types of industrial applications that require extreme environmental protection, such as salt water and strongly acidic conditions.

The benefits of using 2.4360 (Alloy 400) bolts include their high strength and excellent corrosion resistance. The properties of ASTM F467 400 Monel are maintained in a wide range of acidic and alkaline environments. Alloy 400 bolts are ideal for reduced duty applications.

A standout feature of Monel flanges is their excellent resistance to hydrofluoric acid, a particularly difficult acid to handle, at all concentrations up to the boiling point.

Alloy 400’s alkali resistance makes it ideal for deployment in highly acidic environments such as salt water, sulfuric acid or hydrofluoric acid.

Monel 400 or also known as Nickel Alloy 400 is a solid solution alloy used in applications such as valves, pumps, fresh water tanks and propeller shafts, it is a high strength material that can be used over a wide temperature range. It also has excellent corrosion resistance and has applications in many areas in marine and chemical processing.

From a human health perspective, the Nickel 400 Spectacle Blind Flange, which is used to clean, inspect or modify piping systems is effective in completely blocking or sealing off pressure vessels that could contain hydrofluoric acid, which again, is a contact poison.

In addition to high ductility, the material shares several other characteristics with nickel. For example, ASTM B164 Monel 400 round bar is well suited to work in moderately reducing applications because nickel works very well in reducing environments.

Si bien es un metal muy util, tiene un costo prohibitivo en la mayoria de las aplicaciones. Monel 400 cuesta de 5 a 10 veces mas que el niquel o el cobre normales.

Monel 400 is well known for its high strength and corrosion resistant properties. It works in a wide range of temperatures, and is available in multiple forms for a variety of products. Monel 400 is used extensively in (for pipe) piping. Resistant to both steam and seawater, its toughness and anti-corrosive properties make it perfect for heavy duty applications such as transfer (pipe) piping used in oil refineries.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

Alloy 400 is highly regarded as one of the best performing engineering alloys.

MONEL K500 conserva las excelentes propiedades de resistencia a la corrosion de 400, con mayor resistencia y dureza despues del endurecimiento por precipitacion en comparacion con 400.

The corrosion resistance of Monel K-500 is basically the same as Alloy 400, except that in the age hardened condition, Alloy K-500 has a greater tendency to stress corrosion cracking in certain environments. Monel K-500 has been found to be resistant to sour gas environments.

Alloy 400 Seamless Tubing has good ductility which helps to shape and form easily & are available in flat oval, elliptical, round, rectangular & square shapes with 0.030 in. to 1.250 in. OD, 0.008 in. ID & 0.003 in. to 0.280 in. wall thickness.