Monel 400 forgings rings disc disk shaft sleeve contains amounts of manganese

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Monel K500 pipe bend and elbow are resistant to a sour-gas environment

We offers the complete range of Monel Flanges including Slip on, socket weld, blind, lapped, screwed, weld neck, reducing etc.

ALLOY K500,Monel K500 is a Ni-Cu alloy with age-hardening properties imparted by alloying additions of aluminium and titanium. Its basic composition is similar to that of ALLOY400 but the alloying additions make it age hardenable under
controlled conditions of temperature and time

Monel 400 Butt Weld Reducers are resistant to aggressive solvents, acids and bases, and seawater, are highly robust at high temperatures, and are also operable for use in many marine engineering applications.

At room temperature settings, Monel 400 exhibits slight magnetic behavior, thus, the use of WNR 2.4360 Reducing Flange could also be extended to applications that require magnetic characteristics to a certain degree.

It has high strength and excellent corrosion resistance in various acidic and alkaline environments, especially suitable for reducing conditions. It also has good ductility and thermal conductivity.

A nut is a fastener that runs through its inner radius. Nuts are used in combination with bolts to hold a virtually unlimited number of parts, objects and accessories for many types of applications. When Monel 400 alloy is used as a material for making nuts, benefits can be seen in the short and long term. Monel Nickel Copper 400 Nuts provide strength and corrosion resistance in both acidic and alkaline environments. Monel NiCu 400 nuts are also known for their favorable dimensional accuracy and non-corrosion in salt water and hydrofluoric acid.

Monel K500, UNS N05500 (QQ-N-286), is a precipitation hardenable nickel-copper alloy that combines the corrosion resistance of Monel Alloy 400 with higher strength (more than 2x stronger) and hardness.

Alloy 400 is a solid solution alloy that can only be hardened by cold working.

Monel 400 is resistant to steam and sea water as well as highly corrosive solutions such as sulfuric, hydrochloric and hydrofluoric acids after degassing. It has excellent solderability and can withstand very high pressure and weight. The alloy has excellent mechanical properties at sub-zero temperatures, with a melting point of 2370¡ã – 2460¡ã F, and the product can be used at temperatures up to 1000¡ã C.

Monel alloy K-500 pipe bend and elbow have been found to be resistant to a sour-gas environment. After 6 days of continuous immersion in saturated (3500ppm) hydrogen sulfide solutions at acidic and basic pH’s (ranging from 1.0 to 11.0), U-bend specimens of age-hardened sheet show no cracking.

Monel 400 bolts can also be used at higher temperatures. While Monel 400 bolts are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 bolts. Even when cooled to the temperature of liquid hydrogen, Monel 400 will not undergo the ductile to brittle transition that can lead to fracture. This is especially unique compared to most ferrous materials, which are generally stronger but very brittle at extreme low temperatures.

The best machinability for these Monel K500 Lap Joint Flanges is in the annealed condition. Meanwhile, these Monel K500 Socket Weld Flanges are also being offered in different sizes and shapes to our customers.

Over and above the nickel copper base, elements like aluminium and titanium in the chemistry of the Monel K500 Lap Joint Flange proves to be very fruitful. In fact, this modified chemistry along with the heat treatment that is given to the alloy under controlled conditions ensures that the particles of both Ti and Al have been precipitated in the matrix of Monel K500.

The Monel400 bar is a nickel-copper alloy (about 67% ni-23% Cu) that is resistant to seawater and steam as well as salt and corrosive solutions at high temperatures.

MONEL K500 is a age-hardenable Nickel-Copper alloy which combines the corrosion resistance of Alloy 400 with high strength corrosion fatigue and erosion resistance.

These products are manufactured with the latest technologies using high grade raw materials. We are manufacturer in national & international standards.

The strength of Monel400 Cu-Ni alloy is low in the annealed state, so it exhibits a higher degree of strength in the rolled state.

The high-temperature plasticity of the experimental alloy added with trace amounts of Mg, Cr and Co is obviously improved, and it exhibits certain superplasticity. At 1010¡æ, the strain rate sensitivity index m is 0.32, and the maximum elongation is 240%.

Alloy 400 is a nickel copper solid solution strengthened alloy. The alloy is characterized by moderate strength, good weldability, good general corrosion resistance and good toughness.

These Flanges are widely used in various application industries such as petroleum, chemical, construction, engineering, gas and shipbuilding industries and many more.

A finished hex nut, also known as a standard hex nut, has a smaller width across the flats and corners compared to a heavy hex nut. Heavy hex nuts are thicker and heavier in weight. The proof load strength is higher than a standard hex nut. Heavy hex nuts provide increased bearing surface area over finished nuts.

Alloy 400 fasteners have a melting point of 1350 degrees Celsius. The density of the material is higher than most chrome-nickel stainless steels. The density of Monel 400 material is 8.8 grams per cubic centimeter. The strength also exceeds that of the 304, 316 and 310 grades of austenitic stainless steels. The minimum yield strength is 240MPa and the minimum tensile strength is 550MPa. UNS N04400 Studs are made from a single strand of Monel 400 material.

Monel 400 flanges are also available for higher temperatures in reduction environments. While Monel 400 flanges are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 flanges.

We manufacture Monel K500 flanges from nickel and copper alloys. The material has excellent resistance to aggressive materials and solutions such as oxidizing salts, acids, nitrates and other oxidizing agents.

Monel K500 alloy has excellent corrosion resistance, and has higher strength and hardness than Monel 400. This is due to the addition of elements such as Al and Ti to the alloy, and after a certain heat treatment, there are dispersed intermetallic compounds on the substrate.

ASME SB564 Monel UNS N04400 Weld Neck Flanges are utilised in pharmaceutical equipment, heat exchangers, condensers, power generation, etc. ANSI B 16.47 Monel DIN 2.4375 Threaded Flanges are welded to a pipe or fitting with a single full penetration. HT PIPE takes ultimate pride in offering the above mentioned range of products that fall under the Monel Flanges product type that come in two grades, 400 and K500. Also We offer wide range of Monel ASTM B564 400 Flanges such as Monel 400 Slip On Flanges, Monel K500 Weld Neck Flanges.

Overcoming the impact of downtime caused by corrosion, stress and extreme temperatures, and the cost impact of failure rates and safety has driven the industry to look for materials like Monel 400, which provide increased reliability in harsh conditions.

Monel K500 nuts are a result of an age hardening process where aluminum and titanium are added to the nickel-copper base and then precipitated throughout the matrix.

A nyloc nut, also referred to as a nylon-insert lock nut, polymer-insert lock nut, or elastic stop nut, is a kind of locknut with a nylon collar that increases friction on the screw thread.