Monel 400 pipe fittings nickel-copper alloy pipe bend for the acidic and alkaline environment

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

ASME Sb564 Alloy 400 Plate Flanges Monel 400 N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Monel alloys are a group of alloys consisting mainly of nickel and copper with trace amounts of iron, manganese, carbon and silicon. ASTM B865-04 K500 Monel Fastener is a precipitation-hardening nickel-copper alloy. One of the advantages of using alloy UNS N05500 bolts is that the alloy combines the excellent corrosion resistance of Monel 400 alloy with the additional properties of increased tensile strength and hardness.

ASTM B564 UNS N04400 Pipe Flang Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

These flanges are designed to comply with International standards and specifications. Monel R405 offers about the same corrosion resistance as nickel but with higher maximum working pressures and temperatures and at a lower cost due to its superior ability to be machined.

Monel nickel copper k500 hex bolts are often used for standard and advanced applications where a combination of strength and corrosion resistance is a necessity. Monel UNS N05500¡¯s advanced quality corrosion resistance and usability in extreme conditions makes it the perfect choice for a wide range of industrial applications. Some of which, include:

Chemical processing equipment
Marine applications
Petroleum tills & gasoline tanks
Heat exchangers
Valves & pumps
Propeller shafts
Process vessels
And more

Monel is particularly resistant to hydrofluoric and hydrochloric acid. It may be slightly magnetic at room temperature. Monel is more resistant to corrosion than nickel under reducing conditions and more resistant than copper when oxidized.

We manufacture Monel K500 flanges from nickel and copper alloys. The material has excellent resistance to aggressive materials and solutions such as oxidizing salts, acids, nitrates and other oxidizing agents.

These Flanges are widely used in various application industries such as petroleum, chemical, construction, engineering, gas and shipbuilding industries and many more.

Monel 400 or also known as Nickel Alloy 400 is a solid solution alloy used in applications such as valves, pumps, fresh water tanks and propeller shafts, it is a high strength material that can be used over a wide temperature range. It also has excellent corrosion resistance and has applications in many areas in marine and chemical processing.

ASTM B564 UNS N04400 Pipe Flange Monel 400 has a wonderful corrosion resistance by many reducing media such as sulfuric and hydrochloric acids.

It has high strength and excellent corrosion resistance in various acidic and alkaline environments, especially suitable for reducing conditions. It also has good ductility and thermal conductivity.

Typical applications for alloy K-500 pipe bend and elbow are pump shafts and impellers; doctor blades and scrapers; oil-well drill collars and instruments; electronic components; springs; and valve trim.

Both sulfuric acid as well as hydrofluoric acid are highly corrosive solutions and can easily corrode metals, without good resistance to reductive agents.

The levels of molybdenum and copper enable Monel K500 Ring Joint Type Flanges to resist reducing agents and acids. Our wide array of UNS N05500 | Monel K500 Threaded Flanges is utilize in rough oil stills, gas and new water tanks, marine installations and clasp, and concoction preparing gear.

These are widely used in various application industry. We also offer a wide range of monel 400 / K500 Flanges are available in various size, specification & thickness as per the clients requirements.

It exhibits excellent weldability and can withstand very large amounts of pressure and weight.

Over and above the nickel copper base, elements like aluminium and titanium in the chemistry of the Monel K500 Lap Joint Flange proves to be very fruitful. In fact, this modified chemistry along with the heat treatment that is given to the alloy under controlled conditions ensures that the particles of both Ti and Al have been precipitated in the matrix of Monel K500.

The high-temperature plasticity of the experimental alloy added with trace amounts of Mg, Cr and Co is obviously improved, and it exhibits certain superplasticity. At 1010¡æ, the strain rate sensitivity index m is 0.32, and the maximum elongation is 240%.

ASTM B564 UNS N04400 Pipe Flang Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with excellent corrosion resistance in a wide range of marine and chemical environments and has freedom from chloride induced stress-corrosion cracking.

Monel K500 Flat Washers feature aluminum and titanium elements for the excellent corrosion resistance of Alloy 400; improved strength, hardness, erosion resistance and oxidation fatigue resistance. We manufacture all types of Monel K500 machined washers in virtually all shapes and sizes.

Monel 400 UNS N04400 1/2″ Class 150 RF the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Si bien es un metal muy util, tiene un costo prohibitivo en la mayoria de las aplicaciones. Monel 400 cuesta de 5 a 10 veces mas que el niquel o el cobre normales.

Monel K-500 (N05500) Bolts are manufactured by the cold heading and hot forming technologies in nominal diameters ranging from 1/8¡±- 3¡± (M3 ¨C M80). It can be in both USCS/Imperial and metric sizes.

Monel nuts are often used for standard and advanced applications where high levels of strength and superior corrosion resistance is nearly always required. Monel 500¡¯s premium corrosion resistance, strength and usability in extreme conditions makes it the ideal choice for a wide range of industrial applications.

While it is a very useful metal, it is cost prohibitive in most applications. Monel 400 costs 5 to 10 times as much as regular nickel or copper.

Alloy K500 is refined by Electroslag Refining (ESR), ensuring the cleanest and highest quality material. This increased alloy purity limits the potential for hard non-metallic inclusions that can increase machining difficulty, machining time and ultimately lead to part failure. It also has low permeability and is non-magnetic at temperatures as low as -150¡ãF (-101¡ãC).

Hastelloy X is a nickel base alloy that possesses exceptional strength and oxidation resistance up to 2200¡ãF. It has also been found to be exceptionally resistant to stress-corrosion cracking in petrochemical applications. The alloy has excellent forming and welding characteristics.
HASTELLOY? X alloy (UNS N06002 (W86002) is a nickel-chromium-iron-molybdenum
alloy that possesses an exceptional combination of oxidation resistance, fabricability and
high-temperature strength. It has also been found to be exceptionally resistant to stresscorrosion cracking in petrochemical applications. X alloy exhibits good ductility after prolonged exposure at temperatures of 1200, 1400, 1600¡ãF (650, 760 and 870¡ãC) for 16,000
hours.

The Monel400 bar is a nickel-copper alloy (about 67% ni-23% Cu) that is resistant to seawater and steam as well as salt and corrosive solutions at high temperatures.

K-500 is characterized by high corrosion resistance and is an ideal alloy for use in marine environments where constant contact with salt water is required.