Monel 400 pipe fittings pipe bend for Offshore Engineering Chemical Processing and Hydrocarbon Processing

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Alloy 400 (UNS N04400) is a nickel copper alloy with high strength (comparable to structural steel) and toughness. Alloy 400 also has excellent corrosion resistance in a range of media including seawater, hydrofluoric acid, sulphuric acid and alkalis.

Monel K500 fasteners and flanges are virtually non-magnetic and spark resistant, even at temperatures down to -200¡ãF. At temperatures that could rise up to 550C in these mediums, the N06600 Raised Face Weld Neck Flange Ansi B16.5 has been shown to be one of the most resistant out of the other conventional alloys.

Monel 400 is a popular, high performance nickel-copper alloy commonly used in critical and high performance applications.

Astm B564 Monel 400 Blind Flanges A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

This alloy is most commonly used in a range of environments from mildly oxidizing to neutral and moderately reducing conditions. Other areas of application for this material are marine environments and other non-oxidizing chloride solutions.

Our UNS N05500 Flanges provides resistance to stress-corrosion cracking, crevice corrosion, and pitting. These are accessible to our valuable customers in a different range of diameters, wall thicknesses, and sizes at quite affordable rates.

Its properties make it perfect for heavy-duty applications and those that require a high melting point and toughness under the harshest conditions.

The blind flanges are used to close a connection while the slip on flanges are used to adjust a connection position. The ASTM B564 Monel 400 Slip On Flanges allow the seamless pipes to slip onto them so the positioning becomes easy. There are welded flanges as well as threaded flanges.

MONEL K500 is a nickel-copper alloy, precipitation hardenable through additions of aluminum and titanium.

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with excellent corrosion resistance in a wide range of marine and chemical environments and has freedom from chloride induced stress-corrosion cracking.

This is a nickel-copper, solid-solution alloy that is hardenable only by cold working. It has high strength and toughness over a wide temperature range and is resistant to many corrosive environments.

In addition to high ductility, the material shares several other characteristics with nickel. For example, ASTM B164 Monel 400 round bar is well suited to work in moderately reducing applications because nickel works very well in reducing environments.

It has a higher melting point around 2400 degrees Fahrenheit to 2460 degrees Fahrenheit. Primarily Monel K500 grade is a spark resistant alloy. This becomes non-magnetic below -200 degrees Fahrenheit. In terms of cold working operations, magnetic structures can be achieved. The Monel nickel-copper composition of Monel 500 is highly resistant to corrosion, making it ideal for many types of industrial applications that require extreme environmental protection, such as salt water and strongly acidic conditions.

Adding a small amount of Mg to Monel K-500 alloy can increase the grain boundary bonding force and improve high temperature plasticity.

Monel 400 works in a range of acidic and alkaline environments and features excellent ductility and thermal conductivity.

Using the fracture work theory calculation of impurity elements segregation at grain boundaries, it is shown that Mg, Cr and Co can improve the grain boundary bonding force of Ni-Cu alloy, so they can improve the high temperature plasticity of Monel K-500 alloy.

Monel 400 has excellent corrosion resistance in hot concentrated alkaline solution. Monel 400 also resistant to corrosion of neutral solution, water, sea water, atmosphere and organic compounds.

The alloy is used in many fields, especially marine and chemical processing.

Class 150 Monel 400 RTJ Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Monel 400 is a flexible nickel (63% minimum) – copper (34% maximum) alloy retaining strength and toughness at low temperatures while still being effective at temperatures around 1000 degrees F.

Inconel alloy is a family of nickel-chromium superalloys and a trademark of Special Metals Corporation. Inconel 601 is resistant to high-temperature oxidation. The alloy also has good resistance to aqueous corrosion, has high mechanical strength, and is readily formed, machined, and welded.

Alloy 400 fasteners have a melting point of 1350 degrees Celsius. The density of the material is higher than most chrome-nickel stainless steels. The density of Monel 400 material is 8.8 grams per cubic centimeter. The strength also exceeds that of the 304, 316 and 310 grades of austenitic stainless steels. The minimum yield strength is 240MPa and the minimum tensile strength is 550MPa. UNS N04400 Studs are made from a single strand of Monel 400 material.

The alloy has great mechanical properties at subzero temperatures, and with a melting point of 2370¡ã ¨C 2460¡ã F, products can be used at temperatures up to 1000¡ã C.

Class 150 Uns N05500 Socket Weld Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Essentially, Monel 500 is an age-hardened version of Monel 400. This means that Monel 500 is harder and more resistant to corrosion than Monel 400. This material can be used in sour gas applications. Monel K500 Studs maintain corrosion resistance even in high velocity seawater. Hence, these applications are in seawater and marine engineering applications as well as in shipbuilding applications.

It combines the corrosion resistance of Monel K-500 but gives the added advantage of extra strength and hardness (as a result of its age hardening ability).

Monel 400 has very good mechanical properties at sub-zero temperatures, can be used up to 1000¡ãF, and has a melting point of 2370-2460¡ãF. However, Alloy 400 has low strength in the annealed condition, so various tempers can be used to increase the strength.

Socket weld flanges were originally developed for small high pressure pipelines. They have the same static strength as slip-on flanges, but their fatigue strength is 50% higher than double-welded slip-on flanges.

The Monel400 bar is a nickel-copper alloy (about 67% ni-23% Cu) that is resistant to seawater and steam as well as salt and corrosive solutions at high temperatures.

Monel 400 is an alloy of nickel and copper, which means that these components exhibit properties reminiscent of nickel and copper-based alloys. Monel 400 is versatile and can be used for both acid and alkali resistance. Seawater applications are common. One variant is Alloy 405 (UNS N04405). It contains slightly more sulfur, which improves machinability.