monel 400 rod price per kg

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Monel K500 bolts are comprised of a nickel alloy that combines the outstanding corrosion resistance of Monel 400 with increased strength and hardness.

The alloy has been used in a variety of applications. It has excellent resistance to rapidly flowing brackish water or seawater. It is particularly resistant to hydrochloric and hydrofluoric acids when they are de-aerated.

Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.

The Alloy 400 Orifice Flange is a special type that is used to fit pipes together with an orifice. The minimum yield strength of the material is at 195MPa and the minimum tensile strength is 480MPa.

In fact, in comparison to nickel, the corrosion resistance properties of UNS N04400 Orifice Flange tend to be much higher than nickel itself.

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with excellent corrosion resistance in a wide range of marine and chemical environments and has freedom from chloride induced stress-corrosion cracking.

Monel K500 fasteners have trusted properties such as strength, hardness and fracture toughness, which are achieved through the addition of aluminum and titanium as well as nickel and copper alloys. Its basic composition is similar to ALLOY400, but alloys are added to allow age hardening under controlled temperature and time conditions.

Monel 400 is widely used in Brine heaters, sea water scrubbers in tanker inert gas systems.

The alloy has great mechanical properties at subzero temperatures, and with a melting point of 2370¡ã ¨C 2460¡ã F, products can be used at temperatures up to 1000¡ã C.

The chemical composition of Monel K500 Nippo Flanges provides great resistance to a lot of corrosive environments, such as pitting, crevice corrosion, inter ¨C granular corrosion, and stress ¨C corrosion cracking. Monel K500 Spacer Flanges has useful resistance to boiling sulfuric acid up to 40 % concentration, to 60 % concentration at 176 Degree F and in all concentrations to 150 Degree F.

Monel K500 Washers have the same basic iron and carbon composition, but steel also contains a healthy dose of chromium that gives its famous corrosion resistance.

Monel 400 es una de las pocas aleaciones que conserva la resistencia a temperaturas bajo cero, asi que utilicela en estas situaciones.

Alloy 400 is highly regarded as one of the best performing engineering alloys.

Monel K500 bolts offer a unique combination of high strength with similar corrosion resistance to Monel 400 and improved resistance to a sour-gas environments.

Monel alloy K-500 pipe bend and elbow have been found to be resistant to a sour-gas environment. After 6 days of continuous immersion in saturated (3500ppm) hydrogen sulfide solutions at acidic and basic pH’s (ranging from 1.0 to 11.0), U-bend specimens of age-hardened sheet show no cracking.

MONEL K500 no es magnetico. MONEL K500 debe recocerse cuando se suelda, luego la soldadura debe liberarse de la tension antes del envejecimiento.

NAS625 (NCF625, UNS N06625) is a nickel-chromium-molybdenum alloy with an additional of niobium. Matrix stiffening provided by molybdenum and niobium results in high strength. The alloy resists a wide range of severe corrosion environments. It also offers resistance to high temperatures. It also demonstrates remarkable protection against corrosion and oxidation. Its ability to withstand high stress and a wide range of temperatures, both in and out of water, as well as being able to resist corrosion while being exposed to highly acidic environments makes it a fitting choice for nuclear and marine applications.

Monel K500 pipe bend and elbow have corrosion resistance in an extensive range of marine and chemical environments. From pure water to non-oxidising mineral acids, salts and alkalis.

In applications that involve being used at subzero temperature, the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance

Monel 400 bolts can also be used at higher temperatures. While Monel 400 bolts are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 bolts. Even when cooled to the temperature of liquid hydrogen, Monel 400 will not undergo the ductile to brittle transition that can lead to fracture. This is especially unique compared to most ferrous materials, which are generally stronger but very brittle at extreme low temperatures.

Alloy 400 fasteners have a melting point of 1350 degrees Celsius. The density of the material is higher than most chrome-nickel stainless steels. The density of Monel 400 material is 8.8 grams per cubic centimeter. The strength also exceeds that of the 304, 316 and 310 grades of austenitic stainless steels. The minimum yield strength is 240MPa and the minimum tensile strength is 550MPa. UNS N04400 Studs are made from a single strand of Monel 400 material.

Monel 400 Bolt is a nickel-copper alloy, a solid solution nickel alloy that can only be hardened by cold work. Known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher than copper alloys in oxidizing environments. Monel 400 bolts, also known as Alloy 400, are also used in high temperature, caustic and salt solution applications.

Monel 400 is a Nickel-Copper alloy, resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.

The blind flanges are used to close a connection while the slip on flanges are used to adjust a connection position. The ASTM B564 Monel 400 Slip On Flanges allow the seamless pipes to slip onto them so the positioning becomes easy. There are welded flanges as well as threaded flanges.

ASTM B564 UNS N04400 Pipe Flange Monel 400 has a wonderful corrosion resistance by many reducing media such as sulfuric and hydrochloric acids.

These Flanges are widely used in various application industries such as petroleum, chemical, construction, engineering, gas and shipbuilding industries and many more.

Monel K500 Fasteners are thermally applied or manipulated to affect precipitation. This process is called age hardening. These fasteners have a greater tendency to stress corrosion cracking in a variety of harsh environments when exposed to the age hardening process. It has three times the yield strength compared to the standard version. Monel 500 material is an age-hardenable nickel-copper alloy that combines the corrosion resistance of Alloy 400 with the high strength corrosion fatigue and erosion resistance.

The strength of Monel400 Cu-Ni alloy is low in the annealed state, so it exhibits a higher degree of strength in the rolled state.

Monel k500 round bar is an age hardening nickel base alloy. This nickel-based Monel UNS No5500 triangular bar also contains some elemental copper added to its alloy. Copper is known to have good corrosion resistance when added to Monel UNS 5500 spring steel bar, similar to alloy grade 400.

These pipes are difficult to machine because they harden from machining. Alloy 400 welded pipe can be processed using conventional techniques.