Monel 400 Washers resistant to hydrochloric and hydrofluoric acids

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Class 150 Monel 400 RTJ Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Alloy 400 has corrosion resistance, high strength and good weldability. Monel 400 has amazing mechanical properties at sub-zero temperatures. It has a melting point of 2370-2460¡ãF and is easily used at temperatures up to 1000¡ãF.

MONEL K500 is a age-hardenable Nickel-Copper alloy which combines the corrosion resistance of Alloy 400 with high strength corrosion fatigue and erosion resistance.

Monel 400 flanges are a nickel-copper alloy (approximately 67% Ni ¨C 23% Cu) resistant to seawater and steam at high temperatures, as well as salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold work. This nickel alloy has good corrosion resistance, good weldability and high strength.

Alloy 400 is virtually immune to chloride ion stress corrosion cracking in typical environments.

It has good mechanical properties from subzero temperatures up to about 480C.

But since the chief alloyant in the ASTM B564 UNS N04400 SORF Flange is nickel, the resistance to these particular reductive solutions is strong.

Monel 400 products on a project basis is one of our strongest capabilities and is unmatched in our industry.

ASME Sb564 Alloy 400 Plate Flanges Monel 400 N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Alloy 400 is a solid solution of gold that can only be hardened by cold work.

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with good mechanical properties from sub-zero temperatures up to about 550 ¡ãC (1020 ¡ãF) and is approved for pressure vessels with wall temperatures from -10 to 425 ¡ãC (14 to 800 ¡ãF) according to VdTUV-Wbl. 263 and up to 900 ¡ãF (480 ¡ãC) according to ASME Boiler and Pressure Vessel Code.

Monel is particularly resistant to hydrofluoric and hydrochloric acid. It may be slightly magnetic at room temperature. Monel is more resistant to corrosion than nickel under reducing conditions and more resistant than copper when oxidized.

Monel alloy K-500 pipe bend and elbow have been found to be resistant to a sour-gas environment. After 6 days of continuous immersion in saturated (3500ppm) hydrogen sulfide solutions at acidic and basic pH’s (ranging from 1.0 to 11.0), U-bend specimens of age-hardened sheet show no cracking.

MONEL K500 is a age-hardenable Nickel-Copper alloy which combines the corrosion resistance of Alloy 400 with high strength corrosion fatigue and erosion resistance.

Typical applications are valves and pumps; pump and propeller shafts; marine fixtures and fasteners.

It has high strength and excellent corrosion resistance in various acidic and alkaline environments, especially suitable for reducing conditions. It also has good ductility and thermal conductivity.

Monel 400 or also known as Nickel Alloy 400 is a solid solution alloy used in applications such as valves, pumps, fresh water tanks and propeller shafts, it is a high strength material that can be used over a wide temperature range. It also has excellent corrosion resistance and has applications in many areas in marine and chemical processing.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

We manufacture Monel K500 flanges from nickel and copper alloys. The material has excellent resistance to aggressive materials and solutions such as oxidizing salts, acids, nitrates and other oxidizing agents.

These pipes are difficult to machine because they harden from machining. Alloy 400 welded pipe can be processed using conventional techniques.

The chemical composition of Monel K500 ASTM is approximately 65% nickel, 30% copper and 3% aluminum. Monel 500 exhibits excellent corrosion resistance with added high strength corrosion fatigue and erosion resistance. Monel K500 fasteners are non-magnetic at high and low temperatures. The material has the same corrosion resistance as Monel Class 400.

Also known as alloy k500, Monel K500 fasteners and flanges are comprised of a nickel alloy that combines the outstanding corrosion resistance of Monel 400 with increased strength and hardness. Stronger than 400, alloy K500 even retains this strength in corrosive conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas.

Monel K500 Threaded Flanges (UNS N05500) has resistant to a sour ¨C gas environment. Monel K500 Slip On Flanges is often used in Chemical Process Industry: such as in processes involving organic acids, caustic soda and dry chlorine, production of chlorinated plastics, and more.

ASTM B564 UNS N04400 Pipe Flange Monel 400 has a wonderful corrosion resistance by many reducing media such as sulfuric and hydrochloric acids.

Monel K500(alloy K500), UNS N05500 (QQ-N-286), is a precipitation-hardenable nickel-copper alloy that combines the corrosion resistance of Monel alloy 400 with greater strength (over 2x as strong) and hardness. It also has low permeability and is nonmagnetic to temperatures as low as -150¡ãF (-101¡ãC). This alloy shows the corrosion resistant characteristics of grades such as Alloy 400 but with enhanced strength and hardness after precipitation hardening. However, it can be further strengthened by cold working before the precipitation hardening.

The Alloy K500 Pipe Flanges have 63% nickel with 28% copper and carbon, manganese, silicon, sulfur and iron. The iron component in the monel K500 is much lower than that of monel 400. The Monel UNS N04400 Flanges also come under different standards such as ASTM, ASME, ANSI, DIN and all other international standards with varying dimensions. The dimensions of the flanges determine the pressure classes.

Monel 400 is corrosion resistant to most salts, water, alkalis, organic substances, food products, and atmospheric conditions at both normal and elevated temperatures.

Monel K500 pipe bend and elbow are usually used in propeller, pump shafts, pumps, valves used in the manufacture of perchlorethylene, and chlorinated plastics.

Monel 400 is a flexible nickel (63% minimum) – copper (34% maximum) alloy retaining strength and toughness at low temperatures while still being effective at temperatures around 1000 degrees F.

Nickel 400 Annealed Pipe, which is also referred to as a superalloy can be annealed at a temperature of 926¡ãC.