Monel 400 weld neck flange and UNS N04400 Orifice Flange as per ASME B16.5

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Monel 400 is a kind of corrosion resistant alloy with large dosage, wide use and excellent comprehensive performance. Monel 400 has excellent corrosion resistance in hydrofluoric acid and fluorine gas medium.

Monel 400 is resistant to both steam and seawater as well as highly caustic solutions such as sulfuric, hydrochloric, and hydrofluoric acids when they are deaerated.

Alloy 400’s alkali resistance makes it ideal for deployment in highly acidic environments such as salt water, sulfuric acid or hydrofluoric acid.

Monel 400 is an alloy of nickel and copper, typically formulated at about 67% nickel and 33% copper.

Monel 400 es una aleacion de niquel-cobre con excelente resistencia a la corrosion en una variedad de medios.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

Monel K500 fasteners are precipitation hardenable nickel and copper based alloy fasteners. These fasteners were developed for excellent corrosion resistance and have high hardness and strength. ALLOYK500 is a nickel-copper alloy that is age-hardened by the addition of aluminum and titanium alloys.

Monel K500 pipe bend and elbow has excellent mechanical properties from sub-zero temperatures up to about 480C.

Monel 400 is a Nickel-Copper alloy, resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.

Monel 400 flanges are constructed of corrosion-resistant and strong nickel-copper superalloy. The material is easy to weld and form well. These flanges are available in different pressure classes, from Class 150 Monel UNS N04400 flanges to Class 2500, and PN6 to PN64.

Monel K500 alloy has excellent corrosion resistance, and has higher strength and hardness than Monel 400. This is due to the addition of elements such as Al and Ti to the alloy, and after a certain heat treatment, there are dispersed intermetallic compounds on the substrate.

Monel 400 es una aleacion de niquel-cobre resistente a la corrosion en muchos entornos. Consiste en dos solidos cristalinos que forman un nuevo solido.

Monel K500 pipe bend and elbow are exceptionally good dimensional stability.

But since the chief alloyant in the ASTM B564 UNS N04400 SORF Flange is nickel, the resistance to these particular reductive solutions is strong.

Alloy 400 is low in strength in the annealed condition so, a variety of tempers may be used to increase the strength.

This nickel alloy is attacked in sulfur-bearing gases above approximately 700¡ã F and molten sulfur attacks the alloy at temperatures over approximately 500¡ã F.

Overcoming the impact of downtime caused by corrosion, stress and extreme temperatures, and the cost impact of failure rates and safety has driven the industry to look for materials like Monel 400, which provide increased reliability in harsh conditions.

The Asme B16.5 Inconel 600 Flange exhibits good resistance across a broad range of corrosive mediums. The chromium content in the Alloy 600 Flanges gives them better resistance as compared to both Alloy 200 as well as alloy 201 under oxidizing conditions. Also, These Monel K500 Flanges are technologically advanced under the direction of skilled specialists by making use of the premium quality of materials.

ASTM B564 UNS N04400 Pipe Flang Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

Monel K500 pipe bend and elbow are resistant to a sour-gas environment

ASTM B165 (same as ASME SB-165) is a standard specification covering the nickel-copper alloy Monel 400 (UNS N04400) in cold-worked seamless tube form.

Monel 400 is a popular high performance nickel copper alloy commonly used in critical and high performance applications. Monel 400? has high strength, excellent resistance to acid and alkaline environments, and good ductility and thermal conductivity. This alloy maintains its properties and performance in temperatures ranging from subzero to 1,000¡ãF (538¡ãC). Monel 400 can only be hardened by cold work.

Monel 400 is a flexible nickel (63% minimum) – copper (34% maximum) alloy retaining strength and toughness at low temperatures while still being effective at temperatures around 1000 degrees F.

Monel alloys are a group of alloys consisting mainly of nickel and copper with trace amounts of iron, manganese, carbon and silicon. ASTM B865-04 K500 Monel Fastener is a precipitation-hardening nickel-copper alloy. One of the advantages of using alloy UNS N05500 bolts is that the alloy combines the excellent corrosion resistance of Monel 400 alloy with the additional properties of increased tensile strength and hardness.

The Alloy 400 Slip-on Flange is often seen in the marine industry as the alloy exhibits have good resistance to not only seawater but also to high velocity brackish water.

The Alloy 400 Orifice Flange is a special type that is used to fit pipes together with an orifice. The minimum yield strength of the material is at 195MPa and the minimum tensile strength is 480MPa.

In applications that involve being used at subzero temperature, the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance

We are Manufacturers, Supplier and Exporters of Monel K500 Flanges. These Monel R405 flanges are used with stub end or daft which is butt welded to the pipe with the flange loose behind it.

Nickel alloys are combinations of nickel and a variety of other metals that make strong, oxidation-resistant products with an average lifespan of 25 to 35 years. Monel 400 is a nickel-copper alloy containing approximately 67% nickel and 23% copper.

Monel 400 provide superior quality for different types of mechanical, and general engineering applications.