Monel K500 Fastener Grade K500 Monel Alloy Hex Bolts Dealer

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Adding a small amount of Mg to Monel K-500 alloy can increase the grain boundary bonding force and improve high temperature plasticity.

Alloy 400/Monel 400 comes directly from refined ore bodies in Canada, and with a copper content of approximately 30 wt%, it provides a lower cost alternative to commercially pure nickel, but still retains a very similar characteristics.

Alloy 400 Pipe Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Monel 400 UNS N04400 1/2″ Class 150 RF the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with excellent corrosion resistance in a wide range of marine and chemical environments and has freedom from chloride induced stress-corrosion cracking.

Monel K500 is a precipitation-hardenable nickel-copper alloy that combines the excellent corrosion resistance characteristic of Monel 400 with the added advantage of greater strength and hardness.

Monel 400 is widely used in Brine heaters, sea water scrubbers in tanker inert gas systems.

Monel K500 pipe bend and elbow are virtually nonmagnetic, even at quite low temperatures

In fact, in comparison to nickel, the corrosion resistance properties of UNS N04400 Orifice Flange tend to be much higher than nickel itself.

INCOLOY alloys belong to the category of super austenitic stainless steels. These alloys have nickel-chromium-iron as the base metals, with additives such as molybdenum, copper, nitrogen and silicon. These alloys are known for their excellent strength at elevated temperatures and good corrosion resistance in a variety of corrosive environments.
The Alloy 800 Elbow is widely used in various industries and is primarily famous for its excellent mechanical properties. The Werkstoff Nr. 1.4876 End Cap has low gas content, low vapor pressure, and high thermo-electric conductivity.

This nickel alloy is particularly resistant to hydrochloric and hydrofluoric acids when they are de-aerated. As would be expected from its high copper content, alloy 400 is rapidly attacked by nitric acid and ammonia systems.

These are widely used in various application industry. We also offer a wide range of monel 400 / K500 Flanges are available in various size, specification & thickness as per the clients requirements.

ASTM B165 (same as ASME SB-165) is a standard specification covering the nickel-copper alloy Monel 400 (UNS N04400) in cold-worked seamless tube form.

Alloy 400 is a solid solution of gold that can only be hardened by cold work. The nickel alloy has good corrosion resistance, good weldability and high strength

The Monel400 bar is a nickel-copper alloy (about 67% ni-23% Cu) that is resistant to seawater and steam as well as salt and corrosive solutions at high temperatures.

Alloy K500 has approximately three (3) times the yield strength and double the tensile strength when compared with 400. MONEL K500 can be further strengthened by cold working before the precipitation hardening.

The Alloy 400 Slip-on Flange is often seen in the marine industry as the alloy exhibits have good resistance to not only seawater but also to high velocity brackish water.

The Alloy K500 Pipe Flanges have 63% nickel with 28% copper and carbon, manganese, silicon, sulfur and iron. The iron component in the monel K500 is much lower than that of monel 400. The Monel UNS N04400 Flanges also come under different standards such as ASTM, ASME, ANSI, DIN and all other international standards with varying dimensions. The dimensions of the flanges determine the pressure classes.

MonelK-500 alloy has a strong aging cracking tendency after large cold deformation. Cracks initiate on the surface and propagate towards the center. There are both transcrystalline and intercrystalline forms.

Din 931 indicates partially threaded hex head cap screw ¨C The DIN 931 standard will specify the thread tolerance. ? M16; diameter in mm (16 mm) ? In the metric system, all fasteners are assumed coarse thread unless another thread pitch is stated.

While most of the characteristics of Monel K500 Flanges are analogous to monel 400, the former alloy has added bonus of enhanced tensile strength and hardness properties

ALLOY400 is a single-phase solid-solution Ni-Cu alloy with excellent corrosion resistance to a wide range of media.

Monel K500 is a nickel-copper alloy that combines the excellent corrosion resistance of Monel 400 (link) with the added benefits of higher strength and hardness. Performance can be improved by adding aluminum and titanium to the nickel-copper matrix and by heating under controlled conditions to precipitate submicroscopic particles of Ni3 (Ti, Al) throughout the matrix. This is commonly referred to as age hardening or aging.

A286 (1.4980) bolts, also known as alloy 660 bolts, are a stainless steel alloy containing iron, nickel and chromium. A286 bolts are known for their high strength, creep resistance and oxidation resistance at elevated temperatures, once age hardened. As a result, A286 bolts provide high strength from room temperature to approximately 1300¡ãF (700¡ãC).

It is suitable for temperatures up to 1000¡ãF (538¡ãC). Alloy 400 has excellent resistance to cavitation and erosion in fast-flowing brackish or seawater.

While it is a very useful metal, it is cost prohibitive in most applications. Monel 400 costs 5 to 10 times as much as regular nickel or copper.

Monel 400 is a kind of corrosion resistant alloy with large dosage, wide use and excellent comprehensive performance. Monel 400 has excellent corrosion resistance in hydrofluoric acid and fluorine gas medium.

MONEL K500 retains the excellent corrosion resistant characteristics of 400 and has enhanced strength and hardness after precipitation hardening when compared with 400.

When in the age-hardened condition, Monel K-500 has a greater tendency toward stress-corrosion cracking in some environments than Monel 400. Alloy K-500 has approximately three times the yield strength and double the tensile strength when compared with alloy 400.

These products are manufactured with the latest technologies using high grade raw materials. We are manufacturer in national & international standards.