Monel K500 Flanges resisting both pure and salt water

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Monel 400 bolts can also be used at higher temperatures. While Monel 400 bolts are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 bolts. Even when cooled to the temperature of liquid hydrogen, Monel 400 will not undergo the ductile to brittle transition that can lead to fracture. This is especially unique compared to most ferrous materials, which are generally stronger but very brittle at extreme low temperatures.

The best machinability for these Monel K500 Lap Joint Flanges is in the annealed condition. Meanwhile, these Monel K500 Socket Weld Flanges are also being offered in different sizes and shapes to our customers.

Monel 400 has high strength and toughness over a wide temperature range and excellent resistance to many corrosive environments. The composition is shown in the Table below.

These Flanges are widely used in various application industries such as petroleum, chemical, construction, engineering, gas and shipbuilding industries and many more.

Monel nuts are often used for standard and advanced applications where high levels of strength and superior corrosion resistance is nearly always required. Monel 500¡¯s premium corrosion resistance, strength and usability in extreme conditions makes it the ideal choice for a wide range of industrial applications.

Monel K500, UNS N05500 (QQ-N-286), is a precipitation hardenable nickel-copper alloy that combines the corrosion resistance of Monel Alloy 400 with higher strength (more than 2x stronger) and hardness.

Using the fracture work theory calculation of impurity elements segregation at grain boundaries, it is shown that Mg, Cr and Co can improve the grain boundary bonding force of Ni-Cu alloy, so they can improve the high temperature plasticity of Monel K-500 alloy.

Monel K500 bolts are comprised of a nickel alloy that combines the outstanding corrosion resistance of Monel 400 with increased strength and hardness.

The alloy is used in many fields, especially marine and chemical processing.

Monel K500 is a nickel-copper alloy that combines the excellent corrosion resistance of Monel 400 (link) with the added benefits of higher strength and hardness. Performance can be improved by adding aluminum and titanium to the nickel-copper matrix and by heating under controlled conditions to precipitate submicroscopic particles of Ni3 (Ti, Al) throughout the matrix. This is commonly referred to as age hardening or aging.

Monel K500 is a precipitation-hardenable nickel-copper alloy that combines the excellent corrosion resistance characteristic of Monel 400 with the added advantage of greater strength and hardness.

ASTM B165 (same as ASME SB-165) is a standard specification covering the nickel-copper alloy Monel 400 (UNS N04400) in cold-worked seamless tube form.

One of the most important characteristics of Monel 400 is that stress corrosion cracks do not occur in general, and the cutting performance is good. The structure of Monel 400 is single phase solid solution with high strength.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

Monel 400 (UNS N04400) is a nickel-copper alloy with optimum high strength and corrosion resistance. It is widely used in a variety of severe acidic and alkaline environments. Monel is also used in pipes.

A finished hex nut, also known as a standard hex nut, has a smaller width across the flats and corners compared to a heavy hex nut. Heavy hex nuts are thicker and heavier in weight. The proof load strength is higher than a standard hex nut. Heavy hex nuts provide increased bearing surface area over finished nuts.

Monel 400 es una de las pocas aleaciones que conserva la resistencia a temperaturas bajo cero, asi que utilicela en estas situaciones.

MONEL Alloy K-500 (UNS N05500 / W.Nr. 2.4375) is a nickel-copper alloy that combines the excellent corrosion resistance of MONEL Alloy 400 with the added benefits of higher strength and hardness.

Monel 400 is a Nickel-Copper alloy, resistant to sea water and steam at high temperatures as well as to salt and caustic solutions.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

MONEL K-500 alloy has corrosion resistance comparable to 400, but has higher mechanical strength and hardness. Has good thermal corrosion resistance and long-term tissue stability. It is mainly used in the manufacture of turbine blades and gas turbine blades with a working temperature below 750¡ãC on aero-engines, and in the manufacture of fasteners and springs on ships; pumps and valve parts on chemical equipment, and scraping on paper-making equipment. Blades etc.

Class 150 Uns N05500 Socket Weld Flanges A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

N04400 Butt Weld Pipe Fittings has resistance to chloride induced stress corrosion cracking. Also referred as WNR 2.4360 Butt Weld Pipe Fittings, it has excellent mechanical properties from sub-zero temperatures up to 1020¡ã F. Alloy 400 Pipe Fittings are available in different types such as Elbow, Bends, Equal & Unequal (reducing) Tees, Equal & Unequal (reducing) Cross, Concentric & Eccentric Reducer, End Pipe Cap, Long & Short Stubends, Seamless Butt weld pipe fittings, Welded Butt weld pipe fittings, and more.
The Monel 400 alloy has many excellent mechanical properties, making it famous in pipe fittings. The Monel 400 Pipe Fittings can give high performance. It is an alloy of nickel and copper, with a small amount of iron, manganese, carbon, and silicon content. The chemical composition of the Alloy 400 Pipe Fittings results in its high strength. Specialized Monel Fittings Manufacturer In India also concentrates on manufacturing high quality of these pipe fittings due to its high demand in various industries- its resistance towards acids and alkalis are the main reason behind that. The Alloy 400 Buttweld Elbow also possesses good ductility, thermal conductivity, and they can only be hardened by cold-working.

Monel K500 pipe bend and elbow are exceptionally good dimensional stability.

Monel K500 pipe bend and elbow has excellent mechanical properties from sub-zero temperatures up to about 480C.

La aleacion K500 tiene aproximadamente tres (3) veces el limite elastico y el doble de la resistencia a la traccion de 400 en comparacion con 400. MONEL K500 se puede fortalecer aun mas mediante el trabajo en frio antes del endurecimiento por precipitacion.

Monel 400 is also often used for the high tolerance tubing. It exhibits excellent weldability, and it is often found in marine applications such as seawater valves and pump shafts. These tubes are also used in chemical plant equipment, boiler feeders, and heat exchangers. For applications that require a high melting point and toughness under the harshest conditions.
Type Seamless Pipe
Seamless Tube
Welded Pipe
Welded Tube
SAW LSAW ERW EFW
Beveled End, Plain End”
Size OD: 1/2″” ~48″”
Thickness: SCH5~SCHXXS
Length :As per your requirement.”
Manufacturing technique Hot rolling /Hot work ,Cold rolling
Producing Standard ASME B36.10 ASME B36.20

Monel K500 fasteners and flanges are virtually non-magnetic and spark resistant, even at temperatures down to -200¡ãF. At temperatures that could rise up to 550C in these mediums, the N06600 Raised Face Weld Neck Flange Ansi B16.5 has been shown to be one of the most resistant out of the other conventional alloys.

Monel K500 bolts offer a unique combination of high strength with similar corrosion resistance to Monel 400 and improved resistance to a sour-gas environments.

Monel 400 is a flexible nickel (63% minimum) – copper (34% maximum) alloy retaining strength and toughness at low temperatures while still being effective at temperatures around 1000 degrees F.