Monel K500 Hex Nut ASME SF 594 K500 Nuts K500 Monel Alloy Fastener

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

ASTM B564 UNS N04400 Slip on Flange A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

Monel K500 Threaded Flanges (UNS N05500) has resistant to a sour ¨C gas environment. Monel K500 Slip On Flanges is often used in Chemical Process Industry: such as in processes involving organic acids, caustic soda and dry chlorine, production of chlorinated plastics, and more.

In applications that involve being used at subzero temperature, the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance

Alloy 400 is resistance to neutral, alkaline and acid salts is shown, but poor resistance is found with oxidizing acid salts such as ferric chloride.

MONEL K-500 alloy has corrosion resistance comparable to 400, but has higher mechanical strength and hardness. Has good thermal corrosion resistance and long-term tissue stability. It is mainly used in the manufacture of turbine blades and gas turbine blades with a working temperature below 750¡ãC on aero-engines, and in the manufacture of fasteners and springs on ships; pumps and valve parts on chemical equipment, and scraping on paper-making equipment. Blades etc.

A nyloc nut, also referred to as a nylon-insert lock nut, polymer-insert lock nut, or elastic stop nut, is a kind of locknut with a nylon collar that increases friction on the screw thread.

Monel K500(alloy K500), UNS N05500 (QQ-N-286), is a precipitation-hardenable nickel-copper alloy that combines the corrosion resistance of Monel alloy 400 with greater strength (over 2x as strong) and hardness. It also has low permeability and is nonmagnetic to temperatures as low as -150¡ãF (-101¡ãC). This alloy shows the corrosion resistant characteristics of grades such as Alloy 400 but with enhanced strength and hardness after precipitation hardening. However, it can be further strengthened by cold working before the precipitation hardening.

It is resistant to most alkalis, salts, waters, food products, organic substances and atmospheric conditions at normal and elevated temperatures.

La aleacion K500 tiene aproximadamente tres (3) veces el limite elastico y el doble de la resistencia a la traccion de 400 en comparacion con 400. MONEL K500 se puede fortalecer aun mas mediante el trabajo en frio antes del endurecimiento por precipitacion.

Spring washers are locking washers that are used when there is a need to prevent a fastener from loosening as a result of vibration. They are also often called split lock or split ring washers.

Adding a small amount of Mg to Monel K-500 alloy can increase the grain boundary bonding force and improve high temperature plasticity.

Monel 400 has excellent corrosion resistance in hot concentrated alkaline solution.

It combines the corrosion resistance of Monel K-500 but gives the added advantage of extra strength and hardness (as a result of its age hardening ability).

Alloy 400 Pipe Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Monel 400 is resistant to both steam and seawater as well as highly caustic solutions such as sulfuric, hydrochloric, and hydrofluoric acids when they are deaerated.

A finished hex nut, also known as a standard hex nut, has a smaller width across the flats and corners compared to a heavy hex nut. Heavy hex nuts are thicker and heavier in weight. The proof load strength is higher than a standard hex nut. Heavy hex nuts provide increased bearing surface area over finished nuts.

The chemical composition of Monel K500 Nippo Flanges provides great resistance to a lot of corrosive environments, such as pitting, crevice corrosion, inter ¨C granular corrosion, and stress ¨C corrosion cracking. Monel K500 Spacer Flanges has useful resistance to boiling sulfuric acid up to 40 % concentration, to 60 % concentration at 176 Degree F and in all concentrations to 150 Degree F.

Monel 400 provide superior quality for different types of mechanical, and general engineering applications.

ASTM B165 (same as ASME SB-165) is a standard specification covering the nickel-copper alloy Monel 400 (UNS N04400) in cold-worked seamless tube form.

Monel 400 products on a project basis is one of our strongest capabilities and is unmatched in our industry.

Alloy K500 is refined by Electro Slag Refining (ESR), ensuring the cleanest and highest quality of material is supplied.

The alloy can be machined at satisfactory speeds with machine tools commonly used in the industry. Generally, cold drawn or cold drawn stress relief materials are recommended for the best machinability and smoothest finish.

Alloy 400/Monel 400 comes directly from refined ore bodies in Canada, and with a copper content of approximately 30 wt%, it provides a lower cost alternative to commercially pure nickel, but still retains a very similar characteristics.

There are different pressure classes of these flanges ranging from Class 150 Monel UNS N04400 Flanges to class 2500, and PN6 to PN64.

Monel 400 Welded Pipe (NA13, N04400) offer hardness, strength and corrosion resistance with good fabrication capabilities. Monel 400 ERW Pipe can easily be welded by gas metal arc, gas-tungsten arc or shielded metal arc processes using appropriate filler metals.

Monel K500 alloy has excellent corrosion resistance, and has higher strength and hardness than Monel 400. This is due to the addition of elements such as Al and Ti to the alloy, and after a certain heat treatment, there are dispersed intermetallic compounds on the substrate.

The Curie temperature of this alloy lies within the ambient temperature range and is affected by changes in the alloy’s chemical composition. Caution is recommended in applications requiring strong non-magnetic properties.

Din 931 indicates partially threaded hex head cap screw ¨C The DIN 931 standard will specify the thread tolerance. ? M16; diameter in mm (16 mm) ? In the metric system, all fasteners are assumed coarse thread unless another thread pitch is stated.

From a human health perspective, the Nickel 400 Spectacle Blind Flange, which is used to clean, inspect or modify piping systems is effective in completely blocking or sealing off pressure vessels that could contain hydrofluoric acid, which again, is a contact poison.

Monel K500 has about three times the yield strength and twice the tensile strength of Monel 400, and higher mechanical properties can be obtained by cold working or age hardening. Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.