Monel K500 pipe bend and elbow for Oil-well tools and instruments like drill collars

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

This nickel alloy is attacked in sulfur-bearing gases above approximately 700¡ã F and molten sulfur attacks the alloy at temperatures over approximately 500¡ã F.

Monel K500 pipe bend and elbow are usually used in propeller, pump shafts, pumps, valves used in the manufacture of perchlorethylene, and chlorinated plastics.

This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength.

Monel K500 Flanges is further virtually nonmagnetic, even at quite low temperatures. This UNS N05500 Monel are available in various evaluations and sizes, shapes. We offer Monel K500 Blind Flanges that is a unique combination of high strength with similar corrosion resistance to Monel 400 and improved resistance to a sour-gas environments.

Monel K500 is a nickel-copper alloy that combines the excellent corrosion resistance of Monel 400 (link) with the added benefits of higher strength and hardness. Performance can be improved by adding aluminum and titanium to the nickel-copper matrix and by heating under controlled conditions to precipitate submicroscopic particles of Ni3 (Ti, Al) throughout the matrix. This is commonly referred to as age hardening or aging.

These Monel 400 pipes have high strength and toughness over a wide temperature range and have excellent resistance to many corrosive environments.

Common trade names include alloy 400, UNS N04400, Monel alloy. Monel? is a registered tradename of Special Metals Corporation.

MONEL? alloy K-500 (UNS N05500 / W.Nr. 2.4375) is a nickel-copper alloy which combines the excellent corrosion resistance of MONEL alloy 400 with the added advantages of greater strength and hardness. The increased properties are obtained by adding aluminum and titanium to the nickel-copper base.

In fact, in comparison to nickel, the corrosion resistance properties of UNS N04400 Orifice Flange tend to be much higher than nickel itself.

ASTM B564 UNS N04400 Pipe Flang Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

The alloy can be machined at satisfactory speeds with machine tools commonly used in the industry. Generally, cold drawn or cold drawn stress relief materials are recommended for the best machinability and smoothest finish.

Monel K500 is a Nickel-Copper alloy that is precipitation hardenable, due to the additions of Aluminium and Titanium.

The composition of Monel K500 fasteners includes carbon, 2.3% aluminum, manganese, silicon, iron, sulfur and titanium in addition to nickel and copper. It is this unique composition that gives the material its superior strength, extreme corrosion resistance and ductility. Applications for these fasteners include the offshore petroleum industry, power plant applications, petrochemicals, gas handling units, specialty chemicals, and more.

While it is a very useful metal, it is cost prohibitive in most applications. Monel 400 costs 5 to 10 times as much as regular nickel or copper.

Astm B564 Monel 400 Blind Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

It has excellent solderability and can withstand very high pressure and weight. The alloy has excellent mechanical properties at sub-zero temperatures, with a melting point of 2370¡ã – 2460¡ã F, and the product can be used at temperatures up to 1000¡ã C.

Monel 400 is a popular, high performance nickel-copper alloy commonly used in critical and high performance applications.

Alloy 400 is resistance to neutral, alkaline and acid salts is shown, but poor resistance is found with oxidizing acid salts such as ferric chloride.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Monel 400 is essential in heat exchangers, chemical plant equipment, and boiler feeders. It is ideal in wire or rod form and is excellent for trolling wire due to its resistance to seawater.

Monel K500 alloy has excellent corrosion resistance, and has higher strength and hardness than Monel 400. This is due to the addition of elements such as Al and Ti to the alloy, and after a certain heat treatment, there are dispersed intermetallic compounds on the substrate.

Monel K500 Fasteners are thermally applied or manipulated to affect precipitation. This process is called age hardening. These fasteners have a greater tendency to stress corrosion cracking in a variety of harsh environments when exposed to the age hardening process. It has three times the yield strength compared to the standard version. Monel 500 material is an age-hardenable nickel-copper alloy that combines the corrosion resistance of Alloy 400 with the high strength corrosion fatigue and erosion resistance.

Monel K500 fasteners also have some excellent seawater resistance for marine applications. Monel fasteners also have some high-strength metals that have good toughness at high temperatures.

Monel K500 has about three times the yield strength and twice the tensile strength of Monel 400, and higher mechanical properties can be obtained by cold working or age hardening. Monel K500 alloy has the same corrosion resistance as Monel 400 alloy.

The strength of this nickel steel alloy is maintained to 1200¡ã F but stays ductile and tough down to temperatures of 400¡ã F. Its melting range is 2400-2460¡ã F.

Monel 400 is an alloy of nickel and copper, which means that these components exhibit properties reminiscent of nickel and copper-based alloys. Monel 400 is versatile and can be used for both acid and alkali resistance. Seawater applications are common. One variant is Alloy 405 (UNS N04405). It contains slightly more sulfur, which improves machinability.

We offer a comprehensive range of all types Alloy K500 Flanges grades including Slip on flanges, socket weld flanges, blind flanges, lap joint flanges, screwed flanges, weld neck flanges, reducing flanges, spectacle flanges, slip on flanges, plate flanges, screwed flanges etc.

The Monel 400 alloy is also known as super alloy monel. This alloy is available in some standard shapes such as hexagon, round, tube, pipe, plate, strip, sheet and wire.

MonelK-500 alloy has a strong aging cracking tendency after large cold deformation. Cracks initiate on the surface and propagate towards the center. There are both transcrystalline and intercrystalline forms.

K-500 is characterized by high corrosion resistance and is an ideal alloy for use in marine environments where constant contact with salt water is required.