Monel K500 pipe bend and elbow provides corrosion resistance of alloy K-500 is similar to alloy 400

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

The chemical composition of Monel K500 Nippo Flanges provides great resistance to a lot of corrosive environments, such as pitting, crevice corrosion, inter ¨C granular corrosion, and stress ¨C corrosion cracking. Monel K500 Spacer Flanges has useful resistance to boiling sulfuric acid up to 40 % concentration, to 60 % concentration at 176 Degree F and in all concentrations to 150 Degree F.

At room temperature settings, Monel 400 exhibits slight magnetic behavior, thus, the use of WNR 2.4360 Reducing Flange could also be extended to applications that require magnetic characteristics to a certain degree.

A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

Monel bolts, like Monel 400 and K500, are made from a nickel-copper alloy and exhibit high strength, toughness and good corrosion resistance over a wide temperature range.

ASTM B165 (same as ASME SB-165) is a standard specification covering the nickel-copper alloy Monel 400 (UNS N04400) in cold-worked seamless tube form.

Alloy 400 is resistance to neutral, alkaline and acid salts is shown, but poor resistance is found with oxidizing acid salts such as ferric chloride.

This is a nickel-copper, solid-solution alloy that is hardenable only by cold working. It has high strength and toughness over a wide temperature range and is resistant to many corrosive environments.

Monel 400 has excellent corrosion resistance in hydrofluoric acid and fluorine gas medium.

Monel K500 Flanges is further virtually nonmagnetic, even at quite low temperatures. This UNS N05500 Monel are available in various evaluations and sizes, shapes. We offer Monel K500 Blind Flanges that is a unique combination of high strength with similar corrosion resistance to Monel 400 and improved resistance to a sour-gas environments.

Monel 400 Welded Pipe (NA13, N04400) offer hardness, strength and corrosion resistance with good fabrication capabilities. Monel 400 ERW Pipe can easily be welded by gas metal arc, gas-tungsten arc or shielded metal arc processes using appropriate filler metals.

Astm B564 Monel 400 Blind Flanges A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

900# Steel Flanges Nickel Alloy Monel 400 Flange Bleed Ring the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

Monel 400 is a flexible nickel (63% minimum) – copper (34% maximum) alloy retaining strength and toughness at low temperatures while still being effective at temperatures around 1000 degrees F.

ASTM B564 UNS N04400 Slip on Flange A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

Another important characteristic of Monel 400 Blind Flange is its resistance to halides or halogen containing solutions.

ASTM B564 UNS N04400 Slip on Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Monel gaskets, such as Monel 400 and K500, are made of nickel-copper alloys that exhibit high strength, toughness and good corrosion resistance over a wide temperature range. A standout feature of Monel gaskets is their excellent resistance to hydrofluoric acid, a particularly difficult acid to handle, at all concentrations up to the boiling point. For hydrofluoric acid applications, Monel gaskets are probably the most corrosion resistant of all commonly used specialty alloys.

We offers the complete range of Monel Flanges including Slip on, socket weld, blind, lapped, screwed, weld neck, reducing etc.

The superposition of residual stress caused by cold working and aging thermal stress, as well as the preferential embrittlement of the surface layer at the initial stage of aging, are the main reasons for aging cracking of Monel K500 alloy.

Monel K500 bolts and nuts are used in a variety of industries due to their high temperature resistance, high corrosion resistance and durability. It is a nickel-copper alloy with a composition of 63% nickel and 27% copper, among other elements. HT PIPE is a leading manufacturer of Monel K500 Bolts and Nuts of all types and sizes. Fastener applications include the offshore petroleum industry, power plant applications, petrochemicals, gas handling units, specialty chemicals, pharmaceuticals, equipment, seawater applications, heat exchangers, condensers, and the pulp and paper industry.

Monel 400 es una aleacion de niquel-cobre con excelente resistencia a la corrosion en una variedad de medios.

The levels of molybdenum and copper enable Monel K500 Ring Joint Type Flanges to resist reducing agents and acids. Chromium in Monel K500 Spectacle Blind Flanges gives resistance to oxidizing conditions, such as nitric acid solutions, nitrates and oxidizing salts.

ANSI B 16.47 Monel DIN 2.4375 Threaded Flanges are welded to a pipe or fitting with a single full penetration. ASTM B 564 Monel K500 Lap Joint Flanges may be used at all pressures and are available in a full- size range. They can be salvaged for use in systems that erode or corrode quickly. We keep a tab on market trends and demands, to invent new, sustainable and economical products capable of undergoing customization. Our products are fully certified and 100% durable.

Essentially, Monel 500 is an age-hardened version of Monel 400. This means that Monel 500 is harder and more resistant to corrosion than Monel 400. This material can be used in sour gas applications. Monel K500 Studs maintain corrosion resistance even in high velocity seawater. Hence, these applications are in seawater and marine engineering applications as well as in shipbuilding applications.

Alloy 400 Seamless Pipe exhibits excellent resistance to not only caustic solutions but also brine and seawater, which makes it perfect for marine applications.

Typical applications for Monel K500 grade rods include those tasks that take advantage of the alloy’s high tensile strength and corrosion resistance. For example, Monel B865 K500 forged bar can be used to make impellers, propeller shafts, pump shafts.

Class 150 Uns N05500 Socket Weld Flanges A nickel-copper alloy, Monel 400 flanges are a solid solution nickel alloy that can only be hardened by cold working. Best known for its corrosion resistance to reducing media and seawater, Monel 400 is also tougher in oxidizing environments than copper alloys. Also known as alloy 400, Monel 400 flanges are also utilized in high temperature, caustic and salt solution applications.

Monel K500 Bolts, also known as Alloy K500, are composed of a nickel alloy that combines the excellent corrosion resistance of Monel 400 with increased strength and hardness. These additional properties of Monel K500 bolts are the result of an age hardening process in which aluminum and titanium are added to a nickel-copper matrix, which is then precipitated throughout. Compared to 400, this process increases the yield strength of K500 by a factor of approximately 3 (110ksi vs. 45ksi) and doubles the tensile strength (160ksi vs. 83ksi). Monel K500 bolts will maintain their strength down to 1200¡ãF and even maintain their ductility down to -400¡ãF.

Monel 400 or also known as Nickel-Copper 400 is a solid solution alloy that is a high strength material that can be used over a wide temperature range. It also has excellent corrosion resistance and has applications in many areas in marine and chemical processing. It is used in applications such as valves, pumps, fresh water tanks and propeller shafts.

Forged ASME B16.36 Flanged Pipe Fittings Monel 400 N04400 Orifice Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.