Monel K500 pipe bend and elbow with good fatigue and corrosion fatigue resistance

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Alloy 400/Monel 400 comes directly from refined ore bodies in Canada, and with a copper content of approximately 30 wt%, it provides a lower cost alternative to commercially pure nickel, but still retains a very similar characteristics.

Alloy 400 is a solid solution of gold that can only be hardened by cold work. The nickel alloy has good corrosion resistance, good weldability and high strength

The Asme B16.5 Inconel 600 Flange exhibits good resistance across a broad range of corrosive mediums. The chromium content in the Alloy 600 Flanges gives them better resistance as compared to both Alloy 200 as well as alloy 201 under oxidizing conditions. Also, These Monel K500 Flanges are technologically advanced under the direction of skilled specialists by making use of the premium quality of materials.

Alloy 400 is low in strength in the annealed condition so, a variety of tempers may be used to increase the strength.

The Monel K500 flanges available in our company are customized in designs, sizes and shapes. The specification of these flanges is ASTM B564. These flanges range in size from 1/8 inches to 48 inches.

The best machinability for these Monel K500 Lap Joint Flanges is in the annealed condition. Meanwhile, these Monel K500 Socket Weld Flanges are also being offered in different sizes and shapes to our customers.

Monel K500 is a precipitation-hardenable nickel-copper alloy that combines the excellent corrosion resistance characteristic of Monel 400 with the added advantage of greater strength and hardness.

Monel K500 Threaded Flanges (UNS N05500) has resistant to a sour ¨C gas environment. Monel K500 Slip On Flanges is often used in Chemical Process Industry: such as in processes involving organic acids, caustic soda and dry chlorine, production of chlorinated plastics, and more.

This nickel-copper alloy is precipitation hardenable due to the addition of aluminum and titanium. It combines the corrosion resistance of Monel 400 with the added benefits of superior strength and hardness (derived from its age-hardenability). Monel K-500 is also known for its ease of fabrication compared to other superalloys, and the fact that it is essentially nonmagnetic even at low temperatures.

The Monel400 bar is a nickel-copper alloy (about 67% ni-23% Cu) that is resistant to seawater and steam as well as salt and corrosive solutions at high temperatures.

MONEL 400 solid solution alloy can be hardened by cold work, but can be hot worked or cold worked, then annealed into complex structures and welded using an appropriate welding process.

The alloy is slightly magnetic at room temperature. Monel 400 is widely used in the chemical, oil and marine industries.

Monel 400 has high strength and toughness over a wide temperature range and excellent resistance to many corrosive environments. The composition is shown in the Table below.

Using the fracture work theory calculation of impurity elements segregation at grain boundaries, it is shown that Mg, Cr and Co can improve the grain boundary bonding force of Ni-Cu alloy, so they can improve the high temperature plasticity of Monel K-500 alloy.

These flanges are designed to comply with International standards and specifications. Monel R405 offers about the same corrosion resistance as nickel but with higher maximum working pressures and temperatures and at a lower cost due to its superior ability to be machined.

Alloy 400 Blind Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

The combination of very low corrosion rates in high-velocity sea water and high strength make alloy K-500 pipe bend and elbow particularly suitable for shafts of centrifugal pumps in marine service.

Monel 400 flanges are constructed of corrosion-resistant and strong nickel-copper superalloy. The material is easy to weld and form well. These flanges are available in different pressure classes, from Class 150 Monel UNS N04400 flanges to Class 2500, and PN6 to PN64.

Din 931 indicates partially threaded hex head cap screw ¨C The DIN 931 standard will specify the thread tolerance. ? M16; diameter in mm (16 mm) ? In the metric system, all fasteners are assumed coarse thread unless another thread pitch is stated.

While it is a very useful metal, it is cost prohibitive in most applications. Monel 400 costs 5 to 10 times as much as regular nickel or copper.

A finished hex nut, also known as a standard hex nut, has a smaller width across the flats and corners compared to a heavy hex nut. Heavy hex nuts are thicker and heavier in weight. The proof load strength is higher than a standard hex nut. Heavy hex nuts provide increased bearing surface area over finished nuts.

Monel K500 fasteners have trusted properties such as strength, hardness and fracture toughness, which are achieved through the addition of aluminum and titanium as well as nickel and copper alloys. Its basic composition is similar to ALLOY400, but alloys are added to allow age hardening under controlled temperature and time conditions.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Applications that deal with the marine environment are required to be resilient to the effects of saltwater. After all, the concentration of salt in marine water is about 3.5%, enough to corrode ordinary steels with no protective surface treatment.

In fact, in comparison to nickel, the corrosion resistance properties of UNS N04400 Orifice Flange tend to be much higher than nickel itself.

Monel400 alloy is a versatile material that can be used in many industrial applications

Monel 400 has very good mechanical properties at sub-zero temperatures, can be used up to 1000¡ãF, and has a melting point of 2370-2460¡ãF. However, Alloy 400 has low strength in the annealed condition, so various tempers can be used to increase the strength.

It has good mechanical properties from subzero temperatures up to about 480C.

Monel K500 fasteners also have some excellent seawater resistance for marine applications. Monel fasteners also have some high-strength metals that have good toughness at high temperatures.

K-500 is characterized by high corrosion resistance and is an ideal alloy for use in marine environments where constant contact with salt water is required.