Monel400 2.4360 N04400 welded flanges with neck flanges

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

The chemical composition of Monel K500 ASTM is approximately 65% nickel, 30% copper and 3% aluminum. Monel 500 exhibits excellent corrosion resistance with added high strength corrosion fatigue and erosion resistance. Monel K500 fasteners are non-magnetic at high and low temperatures. The material has the same corrosion resistance as Monel Class 400.

Alloy 400 (UNS N04400) is a nickel copper alloy with high strength (comparable to structural steel) and toughness. Alloy 400 also has excellent corrosion resistance in a range of media including seawater, hydrofluoric acid, sulphuric acid and alkalis.

Class 150 Monel 400 RTJ Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

MONEL K500 is a nickel-copper alloy, precipitation hardenable through additions of aluminum and titanium.

La aleacion K500 tiene aproximadamente tres (3) veces el limite elastico y el doble de la resistencia a la traccion de 400 en comparacion con 400. MONEL K500 se puede fortalecer aun mas mediante el trabajo en frio antes del endurecimiento por precipitacion.

Monel 400 is a nickel-copper alloy with excellent corrosion resistance in a wide variety of media. Monel 400 is characterized by good general corrosion resistance, good weldability and moderate to high strength.

Monel 400 products on a project basis is one of our strongest capabilities and is unmatched in our industry.

Stronger than 400, alloy K500 washer even retains this strength in corrosive. conditions, resisting both pure and salt water, as well as non-oxidizing mineral acids, salts, alkalis, and sour gas.

When in the age-hardened condition, Monel K-500 has a greater tendency toward stress-corrosion cracking in some environments than Monel 400. Alloy K-500 has approximately three times the yield strength and double the tensile strength when compared with alloy 400.

Monel K500 Fasteners are thermally applied or manipulated to affect precipitation. This process is called age hardening. These fasteners have a greater tendency to stress corrosion cracking in a variety of harsh environments when exposed to the age hardening process. It has three times the yield strength compared to the standard version. Monel 500 material is an age-hardenable nickel-copper alloy that combines the corrosion resistance of Alloy 400 with the high strength corrosion fatigue and erosion resistance.

Si bien es un metal muy util, tiene un costo prohibitivo en la mayoria de las aplicaciones. Monel 400 cuesta de 5 a 10 veces mas que el niquel o el cobre normales.

Class 150 Uns N05500 Socket Weld Flanges the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance.

The classes define the pressure capacities. The monel 400 flanges have 63% nickel and 28% copper in the composition which makes them stronger.

This alloy is more resistant to nickel under reducing conditions and more resistant than copper under oxidizing conditions, it does show however better resistance to reducing media than oxidizing.

Monel 400 bolts can also be used at higher temperatures. While Monel 400 bolts are typically used at elevated temperatures, they retain their mechanical properties at sub-zero temperatures. The increased hardness at freezing temperatures has been shown to only slightly impair the ductility or impact resistance of Monel 400 bolts. Even when cooled to the temperature of liquid hydrogen, Monel 400 will not undergo the ductile to brittle transition that can lead to fracture. This is especially unique compared to most ferrous materials, which are generally stronger but very brittle at extreme low temperatures.

It has a higher melting point around 2400 degrees Fahrenheit to 2460 degrees Fahrenheit. Primarily Monel K500 grade is a spark resistant alloy. This becomes non-magnetic below -200 degrees Fahrenheit. In terms of cold working operations, magnetic structures can be achieved. The Monel nickel-copper composition of Monel 500 is highly resistant to corrosion, making it ideal for many types of industrial applications that require extreme environmental protection, such as salt water and strongly acidic conditions.

The superposition of residual stress caused by cold working and aging thermal stress, as well as the preferential embrittlement of the surface layer at the initial stage of aging, are the main reasons for aging cracking of Monel K500 alloy.

Reworking of Alloy K-500 is best done while the material is in the annealed or hot worked and quenched condition. However, age hardened materials can be finished to close tolerances and finish. Therefore, the recommended practice is to machine slightly oversize, age harden, and then finish to size.

Monel K500 pipe bend and elbow are exceptionally good dimensional stability.

The Alloy K500 Pipe Flanges have 63% nickel with 28% copper and carbon, manganese, silicon, sulfur and iron. The iron component in the monel K500 is much lower than that of monel 400. The Monel UNS N04400 Flanges also come under different standards such as ASTM, ASME, ANSI, DIN and all other international standards with varying dimensions. The dimensions of the flanges determine the pressure classes.

MONEL K500 no es magnetico. MONEL K500 debe recocerse cuando se suelda, luego la soldadura debe liberarse de la tension antes del envejecimiento.

Monel gaskets, such as Monel 400 and K500, are made of nickel-copper alloys that exhibit high strength, toughness and good corrosion resistance over a wide temperature range. A standout feature of Monel gaskets is their excellent resistance to hydrofluoric acid, a particularly difficult acid to handle, at all concentrations up to the boiling point. For hydrofluoric acid applications, Monel gaskets are probably the most corrosion resistant of all commonly used specialty alloys.

The alloy has been used in a variety of applications. It has excellent resistance to rapidly flowing brackish water or seawater. It is particularly resistant to hydrochloric and hydrofluoric acids when they are de-aerated.

This nickel alloy has good corrosion resistance, good wear resistance and high strength.

Monel 400 is a kind of corrosion resistant alloy with large dosage, wide use and excellent comprehensive performance. Monel 400 has excellent corrosion resistance in hydrofluoric acid and fluorine gas medium.

Monel 400 Bolts and Nuts are made from a nickel-copper alloy for extreme corrosion resistance, especially in sour conditions. The material is also strong and rigid and can be used to produce bolts and nuts for high temperature service. HT PIPE is a leading manufacturer and supplier of Monel 400 Bolts and Nuts of all sizes and types. Among the ingredients are carbon, aluminum, manganese, silicon, iron, sulfur and 63% nickel and 28% copper. This composition gives the material a high melting point.

MONEL K500 is a age-hardenable Nickel-Copper alloy which combines the corrosion resistance of Alloy 400 with high strength corrosion fatigue and erosion resistance.

Typical applications for alloy K-500 pipe bend and elbow are pump shafts and impellers; doctor blades and scrapers; oil-well drill collars and instruments; electronic components; springs; and valve trim.

The Alloy 400 Orifice Flange is a special type that is used to fit pipes together with an orifice. The minimum yield strength of the material is at 195MPa and the minimum tensile strength is 480MPa.

We are a maker, broker, stockist, provider and exporter of ASME SB564 Monel K500 Flanges which are precipitation solidified, high in quality ribs, yielding a rigidity of 115 ksi for a power pressed execution. Monel K500 fasteners and flanges offer a unique combination of high strength with similar corrosion resistance to Monel 400 and improved resistance to a sour-gas environments.