nickel alloy 2.4360 Alloy 400 Monel 400 square head bolt supplier

Nickel Alloy 400 and Monel 400, also known as UNS N04400, is a ductile nickel-copper-based alloy consisting primarily of two-thirds nickel and one-third copper. Nickel Alloy 400 is known for its resistance to a variety of corrosive conditions, including alkalis (or acids), salt water, hydrofluoric acid, and sulfuric acid. Since Monel 400 or Alloy 400 is a cold worked metal, this alloy has high hardness, stiffness and strength. By cold working ASTM B164 UNS N04400 bar stock, the alloy is subjected to higher levels of mechanical stress, which in turn causes changes in the alloy’s microstructure.

SCH40 Monel 400 Pipe is designated as Werkstoff Number 2.4360 and UNS N04400. Alloy 400 Pipe also known as Monel Alloy 400 Pipe, Monel 400 Pipe & Nickel Alloy 400 Pipe.

Nickel-copper-based alloy 400 Monel 2.4360 cold drawn rod is virtually immune to chloride stress-related corrosion cracking when exposed to corrosive media in typical environments. Monel 400 is a copper and nickel based alloy that is popular today due to its high performance. The alloy has excellent acid and alkali resistance. In addition, it has good tensile strength, ductility, excellent thermal conductivity, and can be hardened by cold work. Additionally, it can be used in applications with temperatures ranging from minus to 538 degrees Celsius.

Monel 400 Seamless Tubing, Monel 400 Tubing, Alloy 400 Gas Tube, Monel 400 boiler tubes & Monel 400 Polish Tube are most often found in chemical plant equipment due to their strong resistance to chemical corrosion.

A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

Monel K500, UNS N05500 (QQ-N-286), is a precipitation-hardenable nickel-copper alloy that combines the corrosion resistance of Monel alloy 400 with greater strength (over 2x as strong) and hardness. It also has low permeability and is nonmagnetic to temperatures as low as -150¡ãF (-101¡ãC).

Our UNS N05500 Flanges provides resistance to stress-corrosion cracking, crevice corrosion, and pitting. These are accessible to our valuable customers in a different range of diameters, wall thicknesses, and sizes at quite affordable rates.

In order to convey the pipeline, it is necessary to remove the straight hose in the pipeline. When using various pipelines, various pipelines must be used. When the pipeline is used, the elbow must be used to change the size of the pipeline. When bifurcating, the three-way pipe The flange connection used when the joint is used with various pipe joints, in order to reach the long-distance transmission pipeline, in order to reach the thermal expansion and cold contraction joint or effective connection aging of the pipeline, the long-distance expansion and cold contraction joint is used for the connection of the pipeline. , In the connection of various instruments, there are also the connectors and plugs of the instrument phase.

The Monel 400 alloy is also known as super alloy monel. This alloy is available in some standard shapes such as hexagon, round, tube, pipe, plate, strip, sheet and wire.

Monel 400 works in a range of acidic and alkaline environments and features excellent ductility and thermal conductivity.

Monel 400 flanges are constructed of corrosion-resistant and strong nickel-copper superalloy. The material is easy to weld and form well. These flanges are available in different pressure classes, from Class 150 Monel UNS N04400 flanges to Class 2500, and PN6 to PN64.

Inconel alloy is a family of nickel-chromium superalloys and a trademark of Special Metals Corporation. Inconel 601 is resistant to high-temperature oxidation. The alloy also has good resistance to aqueous corrosion, has high mechanical strength, and is readily formed, machined, and welded.

ASTM B564 UNS N04400 Pipe Flang Monel 400 is a nickel-copper alloy (about 67% Ni ¨C 23% Cu) that is resistant to sea water and steam at high temperatures as well as to salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold working. This nickel alloy exhibits characteristics like good corrosion resistance, good weldability and high strength. A low corrosion rate in rapidly flowing brackish or seawater combined with excellent resistance to stress-corrosion cracking in most freshwaters, and its resistance to a variety of corrosive conditions led to its wide use in marine applications and other non-oxidizing chloride solutions.

Alloy K500 studs are threaded rods with threads on both ends. They can be of different types depending on thread distance from center and thread type. The material is resistant to high temperature and high pressure. It has a melting point of 1350 degrees Celsius, a minimum yield strength of 790MPa and a minimum tensile strength of 1100MPa. These values are twice as strong as level 304.

This nickel-copper alloy is precipitation hardenable due to the addition of aluminum and titanium. It combines the corrosion resistance of Monel 400 with the added benefits of superior strength and hardness (derived from its age-hardenability). Monel K-500 is also known for its ease of fabrication compared to other superalloys, and the fact that it is essentially nonmagnetic even at low temperatures.

Monel K500 pipe bend and elbow has excellent mechanical properties from sub-zero temperatures up to about 480C.

Alloy 400 fasteners have a melting point of 1350 degrees Celsius. The density of the material is higher than most chrome-nickel stainless steels. The density of Monel 400 material is 8.8 grams per cubic centimeter. The strength also exceeds that of the 304, 316 and 310 grades of austenitic stainless steels. The minimum yield strength is 240MPa and the minimum tensile strength is 550MPa. UNS N04400 Studs are made from a single strand of Monel 400 material.

Monel 400 and K500 nuts also exhibit excellent corrosion resistance in marine applications and have reasonable corrosion resistance to sulfuric and hydrochloric acids under reducing conditions. A standout feature of monel nuts is their excellent resistance to hydrofluoric acid, a particularly difficult acid to handle, at all concentrations up to the boiling point. For hydrofluoric acid applications, Monel nuts are probably the most corrosion resistant of all commonly used specialty alloys.

ASTM B564 UNS N04400 Slip on Flange the Monel 400 Flanges shows evidence of excellent temperature. On the other hand, properties such as Strength and hardness of the Monel 400 Lap Joint Flange is only slightly diminished with regards to the other properties like ductility or impact resistance. Besides its the alloy is renowned for its toughness or impact strength properties. And therefore is very appropriately used in applications like chemical and hydro-carbon processing, heat exchangers, valves and pumps.

Nickel alloys are some of the most useful materials for manufacturing technically superior pipes and tubes for industrial applications. Their inherent properties make them viable for a wide range of uses. Nickel alloys are exceptionally corrosion resistant and can be used in high-temperature environments.

Monel 400 provide superior quality for different types of mechanical, and general engineering applications.

The corrosion resistance of Monel alloy K-500 is subtantially equivalent to that of alloy 400 except that, when in the age-hardened condition, alloy K-500 has a greater tendency toward stress-corrosion cracking in some environments.

MONEL K-500 alloy has corrosion resistance comparable to 400, but has higher mechanical strength and hardness. Has good thermal corrosion resistance and long-term tissue stability. It is mainly used in the manufacture of turbine blades and gas turbine blades with a working temperature below 750¡ãC on aero-engines, and in the manufacture of fasteners and springs on ships; pumps and valve parts on chemical equipment, and scraping on paper-making equipment. Blades etc.

Monel 400 flanges are a nickel-copper alloy (approximately 67% Ni ¨C 23% Cu) resistant to seawater and steam at high temperatures, as well as salt and caustic solutions. Alloy 400 is a solid solution alloy that can only be hardened by cold work. This nickel alloy has good corrosion resistance, good weldability and high strength.

INCOLOY alloys belong to the category of super austenitic stainless steels. These alloys have nickel-chromium-iron as the base metals, with additives such as molybdenum, copper, nitrogen and silicon. These alloys are known for their excellent strength at elevated temperatures and good corrosion resistance in a variety of corrosive environments.
The Alloy 800 Elbow is widely used in various industries and is primarily famous for its excellent mechanical properties. The Werkstoff Nr. 1.4876 End Cap has low gas content, low vapor pressure, and high thermo-electric conductivity.

Monelk500, also known as UNS N05500, has the same corrosion resistance as monel400, but has higher mechanical strength and hardness. It has good corrosion resistance and long-term organizational stability.

Generally, its corrosion resistance is very good in reducing environments, but poor in oxidizing conditions.

The strength of Monel400 Cu-Ni alloy is low in the annealed state, so it exhibits a higher degree of strength in the rolled state.

MonelK-500 alloy has a strong aging cracking tendency after large cold deformation. Cracks initiate on the surface and propagate towards the center. There are both transcrystalline and intercrystalline forms.

ASTM B564 UNS N04400 Pipe Flange Monel 400 has a wonderful corrosion resistance by many reducing media such as sulfuric and hydrochloric acids.

Monel K-500 combines the excellent corrosion resistance of Monel 400 with the added benefits of higher strength and hardness. Performance can be improved by adding aluminum and titanium to the nickel-copper matrix and by heating under controlled conditions to precipitate submicroscopic particles of Ni 3 (Ti, Al) throughout the matrix.

It is not useful in oxidizing acids, such as nitric acid and nitrous.